This paper reports on an aluminum nitride (AlN) piezoelectric micromachined ultrasound transducer (PMUT) array for photoacoustic (PA) imaging, where the high-order resonance modes of the PMUT are utilized to improve imaging resolution. A flexural vibration mode (FVM) PMUT is fabricated and applied in a photoacoustic imaging (PAI) system. Specifically, the microelectromechanical system (MEMS)-based PMUT is suitable for PA endoscopic imaging of blood vessels and bronchi due to its miniature size and high sensitivity. More importantly, AlN is a nontoxic material, which makes it harmless for biomedical applications. In the PAI system, the AlN PMUT array is used to detect PA signals, and the acousto–mechanical response is designed and optimized at the PMUT’s fundamental resonance. In this work, we focus on the high-order resonance performance of the PMUT PAI beyond the fundamental resonance. The acoustic and electrical responses of the PMUT’s high-order resonance modes are characterized and analyzed. The fundamental and three high-order resonance bandwidths are 2.2, 8.8, 18.5, and 48.2 kHz. Compared with the resolution at the fundamental resonance mode, the resolutions at third- and fourth-order resonance modes increase by 38.7% and 76.9% in a phantom experiment. The high-order resonance modes of the AlN PMUT sensor array provide higher central frequency and wider bandwidth for PA signal detection, which increase the resolution of PAI compared to the PMUT working at the fundamental resonance mode.

Transit-time ultrasonic flowmeters (TTUFs) are among the most widely used devices for flow measurements. However, traditional TTUFs are usually based on a bulk piezoelectric transducer, which limits their application in small-diameter channels. In this paper, we developed a miniaturized TTUF based on scandium-doped aluminum nitride (ScAlN) piezoelectric micromachined ultrasonic transducers (PMUTs). The proposed TTUF contains two PMUT-based transceivers and a π-type channel. The PMUTs contain 13 × 13 square cells with dimensions of 2.8 × 2.8 mm². To compensate for the acoustic impedance mismatch with liquid, a layer of polyurethane is added to the surface of the PMUTs as a matching layer. The PMUT-based transceivers show good transmitting sensitivity (with 0.94 MPa/V surface pressure) and receiving sensitivity (1.79 mV/kPa) at a frequency of 1 MHz in water. Moreover, the dimensions of the π-type channel are optimized to achieve a measurement sensitivity of 82 ns/(m/s) and a signal-to-noise ratio (SNR) better than 15 dB. Finally, we integrate the fabricated PMUTs into the TDC-GP30 platform. The experimental results show that the developed TTUF provides a wide range of flow measurements from 2 to 300 L/h in a channel of 4 mm diameter, which is smaller than most reported channels. The accuracy and repeatability of the TTUF are within 0.2% and 1%, respectively. The proposed TTUF shows great application potential in industrial applications such as medical and chemical applications.

In this work, a miniaturized, low-cost, low-power and high-sensitivity AlN-based micro-electro-mechanical system (MEMS) hydrophone is proposed for monitoring water pipeline leaks. The proposed MEMS Hydrophone consists of a piezoelectric micromachined ultrasonic transducer (PMUT) array, an acoustic matching layer and a pre-amplifier amplifier circuit. The array has 4 (2 × 2) PMUT elements with a first-order resonant frequency of 41.58 kHz. Due to impedance matching of the acoustic matching layer and the 40 dB gain of the pre-amplifier amplifier circuit, the packaged MEMS Hydrophone has a high sound pressure sensitivity of −170 ± 2 dB (re: 1 V/μPa). The performance with respect to detecting pipeline leaks and locating leak points is demonstrated on a 31 m stainless leaking pipeline platform. The standard deviation (STD) of the hydroacoustic signal and Monitoring Index Efficiency (MIE) are extracted as features of the pipeline leak. A random forest model is trained for accurately classifying the leak and no-leak cases using the above features, and the accuracy of the model is about 97.69%. The cross-correlation method is used to locate the leak point, and the localization relative error is about 10.84% for a small leak of 12 L/min.

In this paper, a high-sensitivity microelectromechanical system (MEMS) piezoelectric accelerometer based on a Scandium-doped Aluminum Nitride (ScAlN) thin film is proposed. The primary structure of this accelerometer is a silicon proof mass fixed by four piezoelectric cantilever beams. In order to enhance the sensitivity of the accelerometer, the Sc_0.2Al_0.8N piezoelectric film is used in the device. The transverse piezoelectric coefficient d₃₁ of the Sc_0.2Al_0.8N piezoelectric film is measured by the cantilever beam method and found to be −4.7661 pC/N, which is approximately two to three times greater than that of a pure AlN film. To further enhance the sensitivity of the accelerometer, the top electrodes are divided into inner and outer electrodes; then, the four piezoelectric cantilever beams can achieve a series connection by these inner and outer electrodes. Subsequently, theoretical and finite element models are established to analyze the effectiveness of the above structure. After fabricating the device, the measurement results demonstrate that the resonant frequency of the device is 7.24 kHz and the operating frequency is 56 Hz to 2360 Hz. At a frequency of 480 Hz, the sensitivity, minimum detectable acceleration, and resolution of the device are 2.448 mV/g, 1 mg, and 1 mg, respectively. The linearity of the accelerometer is good for accelerations less than 2 g. The proposed piezoelectric MEMS accelerometer has demonstrated high sensitivity and linearity, making it suitable for accurately detecting low-frequency vibrations.

This paper reports broadened bandwidth aluminum nitride (AlN) piezoelectric micromachined ultrasound transducers (BB-PMUT) for photoacoustic imaging (PAI). PMUT based on micro-electromechanical systems (MEMS) technology gains significant attention for PA endoscopic imaging inside colorectal and even blood vessel due to its miniature size, high sensitivity and versatility. Broadened bandwidth, resulting from variable membrane cavity size during the fabrication process, provides benefit to imaging spatial resolution improvement. Moreover, AlN thin film is a non-toxic material, which makes it harmless for biomedical applications with potential of CMOS-MEMS integration. In this work, a BB-PMUT is designed and fabricated. The vibration modes, impedance and bandwidth are analyzed. The BB-PMUT provides a wider fractional bandwidth (65%) for signal detection, which significantly increases the resolution compared with traditional single frequency PMUT design. We have conducted experimental validation on an agar sample to present the sensor's performance in improving axial resolution.

Bowel sounds contain some important human physiological parameters which can reflect information about intestinal function. In this work, in order to realize real-time monitoring of bowel sounds, a portable and wearable bowel sound electronic monitor based on piezoelectric micromachined ultrasonic transducers (PMUTs) is proposed. This prototype consists of a sensing module to collect bowel sounds and a GUI (graphical user interface) based on LabVIEW to display real-time bowel sound signals. The sensing module is composed of four PMUTs connected in parallel and a signal conditioning circuit. The sensitivity, noise resolution, and non-linearity of the bowel sound monitor are measured in this work. The result indicates that the designed prototype has high sensitivity (−142.69 dB), high noise resolution (50 dB at 100 Hz), and small non-linearity. To demonstrate the characteristic of the designed electronic monitor, continuous bowel sound monitoring is performed using the electronic monitor and a stethoscope on a healthy human before and after a meal. Through comparing the experimental results and analyzing the signals in the time domain and frequency domain, this bowel sound monitor is demonstrated to record bowel sounds from the human intestine. This work displays the potential of the sensor for the daily monitoring of bowel sounds.