The manufacturing of thermally stable solar coatings with high photo-thermal performance represents a key factor for the further deployment of the CSP technology. Since 2005, ENEA has been developing solar coatings suitable for medium and high temperature applications based on the technology of double nitride cermet, by employing silver and tungsten as infrared reflectors, respectively. Thanks to the high infrared reflectance of silver, the corresponding coatings have better optical performance than those with tungsten; however, the high diffusivity of silver compromises its use at high temperature. In order to improve the structural and chemical stability at medium and high temperature of coatings based on silver, this infrared reflector was placed between compact and uniform layers of metal and cermet manufactured by using high-energy and fast deposition processes. In particular, an Unbalanced Magnetron cathode was adopted to promote an ion-assisted deposition process that improved uniformity and compactness of the metal and cermet films. The new coating shows no photo-thermal parameters degradation after 25 years of service at the operating temperature of 400 °C, while its photo-thermal conversion efficiency decreases by only 1.5% after 25 years of service at an operating temperature of 514 °C.
The present work introduces a new solar selective absorber coating (SSAC) for the receiver tube of Concentrated Solar Power (CSP) systems, proposing silver as an infrared reflector for application at 550 °C. In the past, the Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA) has developed SSACs suitable for applications at 550 °C, featuring solar absorbers based on graded multilayer cermet of WN-AlN and W-Al2O3 and an infrared reflector of tungsten. Although these coatings ensured properly stable photothermal performance at 550 °C, due to the low tungsten diffusivity, their hemispherical emittance could be reduced by using metals with higher reflectance in the infrared region, like silver. However, the high diffusivity of silver compromises its use at high temperatures. This last drawback has been addressed by foreseeing two stabilizing layers enclosing the Ag infrared reflector. One W stabilizing layer was placed between the substrate and the Ag infrared reflector, whereas a second stabilizing layer, selected among aluminum nitride deposited with a low and high nitrogen flow and aluminum oxide deposited at a low oxygen flow, was placed between the Ag infrared reflector and the solar absorber. Accelerated aging tests revealed a negligible (not detectable) degradation of the solar absorptance for the new SSACs. Furthermore, the hemispherical emittance at 550 °C increased by 0.75% and 0.42% for solar coatings with aluminum nitride stabilizing layers deposited through a high and low nitrogen flow, respectively. Differently, the increase was evaluated as being equal to 0.08% for the solar coating with an aluminum oxide stabilizing layer deposited through a low oxygen flow. The manufactured solar coating with a stabilizing layer of aluminum nitride deposited with a low nitrogen flow exhibited a solar absorptance of 95%, comparable to ENEA coatings incorporating a W infrared reflector for applications at 550 °C, whereas the estimated hemispherical emittance at 550 °C was 2% lower than that of the best ENEA coating with a W infrared reflector for the same temperature.
In parabolic trough technology, the development of thermally and structurally stable solar coatings plays a key role in determining the efficiency, durability, and economic feasibility of tube receivers. A cermet-based solar coating is typically constituted by a thin film stratification, where a multilayer graded cermet is placed between an infrared metallic reflector and an antireflection filter. This work reports the realization of materials based on Al2O3 and W characterized by high structural and chemical stability in vacuum at high temperature, obtained through the optimization of high-deposition-rate processes. Al2O3 material, employed as the antireflection layer, was deposited through a reactive magnetron sputtering process at a high deposition rate. Cermet materials based on W-Al2O3 were deposited and employed as absorber layers by implementing reactive magnetron co-sputtering processes. An investigation into the stability of the realized samples was carried out by means of several material characterization methods before and after the annealing process in vacuum (1 × 10−3 Pa) at high temperature (620 °C). The structural properties of the samples were evaluated using Raman spectroscopy and XRD measurements, revealing a negligible presence of oxides that can compromise the structural stability. Spectrophotometric analysis showed little variations between the deposited and annealed samples, clearly indicating the high structural stability.
This work presents a modular W/Ag/AlN infrared reflector for solar selective absorber coatings (SSACs) intended for CSP/CST receiver tubes operating under vacuum at 550 °C. Optical analyses showed that AlN deposition preserved Ag infrared reflectance. Two Ag/AlN bilayers reduced the W reflector’s hemispherical emittance from 7.5% to 2.9%, calculated from room-temperature reflectance weighted at 550 °C. The reflector was first integrated into an SSAC for durability assessment. Accelerated aging under vacuum at 620, 650, and 690 °C yielded an Arrhenius activation energy of 497 kJ/mol and predicted an emittance increase of 0.34 percentage points after 25 years at 550 °C (8 h/day). An optimized SSAC subsequently achieved 95.2% solar absorptance and 11.3% hemispherical emittance on stainless steel, based on room-temperature reflectance. Simulations incorporating temperature-dependent optical properties estimated an emittance of 13.4% at 550 °C, versus 14.7% for a W-based coating. The previous Ag-based coating had lower estimated emittance (11.0%) but required three times more Ag. A 96 h aging test at 650 °C showed that the optimized SSAC exhibited an emittance degradation rate comparable to those of the samples of the coating used in the durability study, supporting the long-term stability prediction for the optimized architecture.