In the present study, pulsed laser post-processing was applied to improve the properties of the thermally sprayed NiCrCoFeCBSi/40 wt.% WC coatings. The powder mix was deposited onto a mild steel substrate by flame spray method and then the as-sprayed coatings were processed by Nd:YAG laser. The peak power density applied was between 4.00 × 10⁶ and 5.71 × 10⁶ W/cm², and the laser operating speed ranged between 100 and 400 mm/min, providing processing in a melting mode. Scanning electron microscopy, energy dispersive spectroscopy, Knop hardness measurements, and “ball-on-disc” dry friction tests were applied to study the effect of the processing parameters on the geometry of laser pass and microstructure, hardness, and tribology of the processed layers. The results obtained revealed that pulsed laser processing provides a monolithic remelted coating layer with the microstructure of ultrafine, W-rich dendrites in Ni-based matrix, where size and distribution of W-rich dendrites periodically vary across remelted layer depth. The composition of W-rich dendrites can be attributed to a carbide of type (W, Cr, Ni, Fe)C. The cracks sensitivity of coatings was visibly reduced with the reduction of power density applied. The hardness of coatings was between ~1070 and ~1140 HK0.2 and correlated with microstructure size, being dependent on the processing parameters. The friction coefficient and wear rate of coatings during dry sliding were reduced by up to ~30% and up to ~2.4 times, respectively, after laser processing.

The possibility of using polymer concrete for metal cutting machine beds is analyzed. A comparison of the structures of the machine beds made of polymer concrete and cast iron is made. The frequency of the body of the machine beds made of polymer concrete and cast iron is determined. An analysis of the stress–strain state under static loads is carried out. To increase resistance to wear, it is proposed to spray polymer concrete frames are proposed by the gas–thermal method. The installation of thermal spraying for guide machine beds is given. The optimal parameters for spraying the guides of the machine beds made of polymer concrete are established calculated using the finite element method for the guide beds of metal cutting machine tools using polymer concrete with gaseous coating. The manufacture of the foundation bed from polymer concrete increases the vibration resistance of the machine by 1.4 times. At the same time, the metal consumption of metal cutting machines will decrease by 60%. To increase the wear resistance of the frame guides, it is proposed to use thermal spraying with certain modes typical for polymer concrete. The installation of thermal spraying for bed guides is given. Calculating using the finite element method for the guide beds of metal cutting machines showed that the use of polymer concrete with a wear-resistant coating is justified.

Reducing the weight of the structures and choosing the materials used in mechanical engineering is an important and pressing economic and environmental problem. The design of a gear pump is developed from the point of view of the geometry of the gears, as well as the casing. This paper tested a gear pump casing using the environment of the ABAQUS 2020 system in the field of statistical strength analysis using the finite element method. The tests were carried out on the pump body and the front and rear covers, which were made of three types of materials (cast iron, aluminum, and polycarbonate), at a pressure of 28 MPa. After loading, the maximum stresses in the aluminum casing (177 MPa), the cast iron casing (157 MPa), and the polycarbonate (200 MPa) were determined. The largest stress concentrators are the grooves at the bottom of the pump casing. Rounding the internal chamber of the casing with a radius of 4 mm made it possible to reduce stress in this zone by 10 MPa. The parametric optimization of the front and back covers of the gear pump made it possible to reduce the total weight of the aluminum structure by 14%, the cast iron by 12%, and the polycarbonate by 16%. The 3D models show areas of minimal stress where the size and weight of the structure could be reduced in the future using a comprehensive approach involving parametric and topological analysis.

As a result of R&D, a measuring system for controlling the thickness of the HDPE/LDPE (high-density polyethylene/low-density polyethylene) polymer geomembrane was developed using automation equipment. The relevance of this work consists of the development of a domestic, relatively inexpensive system for controlling the thickness of the HDPE/LDPE polymer geomembrane in production conditions based on modern equipment for enterprise automation. The scientific novelty consists of the use of original design solutions in the development of hardware and software complex mechanisms that allow controlling the thickness of the HDPE/LDPE polymer geomembrane layers along the entire width of the shaft, excluding deformation of the film as a result of foreign bodies entering during extrusion, cuts, monitoring the quality of the film in real time, as well as the possibility of analyzing the measured parameters in the database of the automated system.

Gear pumps are hydraulic machines capable of transferring energy and performing work in pumping fluid. This study presents an analysis of the hydrodynamic model of an external multiple gear pump in order to analyze the fluid flow in combinations of single and different viscosities at the same and different pressures and speeds. Solidworks Flow Simulation 2016 was used to analyze fluid flow. When the radius of the rounding on the collector inner surface is increased from 3 to 15 mm, the pressure drop decreases by 13%. When the radius of the manifold is 3 mm, cavitations are observed. With a liquid distribution system with four input ports and one outlet port in the top cover, the gear pump can handle liquids of viscosity classes 5 to 10. The speed should not exceed 1200 rpm if the liquid has a kinematic viscosity of 10 cSt. The pressure drop and velocity distribution of the liquid in the pressure and suction lines are the same. When the speed changes from 400 to 1200 rpm, the pressure drop increases five times, and the velocity increases three times. At a constant speed of 1000 rpm and an inlet pressure of 10 MPa but with different viscosities, the pressure drop decreases 8 times, and the speed increases 1.5 times. When the inlet pressure is 6 to 24 MPa, with constant speed and the same viscosity, the pressure drop and fluid velocity practically do not change. The dependence of pressure drop on the number of revolutions and radius of the rounding of the inner surface of the collector is statistically significant.

The given article provides material on the development of the CADS applied for production processes of component part machining for single-piece production and repair conditions. The article describes technique used to organize a data fl ow and hose methods of machining which cannot be applied under these conditions of machining. This research uses graph theory. The article describes the developed algorithm for machining planning of details. A mathematical model of transitions in the technological process for the processing of parts has been obtained.The developed design CADS reduces the number of errors in the development of production processes. The article describes database for machining planning. In order to form input data, knowledge of production processes of analogous machine parts or products production is not required. Thus developed models of system determines of machine-part production stages. This system gives schemes of its basing, a set of bases and an order of their preparation and forming of schemes of technological dimensional chains. This system counts and recounts interoperational dimensions. Developed models and system allows to increase amount of output information to the level of operational fl ow charts. The designed system gives the chance of its use in modern multiproduct. This system is universal, multifunctional.