Roberta Capuano

Dr. Roberta Capuano

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2021 in Foods
Verified
Journal Article
Open access
PDF file
Annachiara PirozziAnnachiara Pirozzi
Annachiara Pirozzi
RCRoberta Capuano
Roberta Capuano
RARoberto Avolio
Roberto Avolio
Gennaro GentileGennaro Gentile
Gennaro Gentile
Giovanna FerrariGiovanna Ferrari
Giovanna Ferrari
Francesco DonsìFrancesco Donsì
Francesco Donsì
This work aimed at studying the stabilization of O/W Pickering emulsions using nanosized cellulosic material, produced from raw cellulose or tomato pomace through different mechanical treatments, such as ball milling (BM) and high-pressure homogenization (HPH). The cellulose nanofibrils obtained via HPH, which exhibited longer fibers with higher flexibility than those obtained via ball milling, are characterized by lower interfacial tension values and higher viscosity, as well as better emulsion stabilization capability. Emulsion stability tests, carried out at 4 °C for 28 d or under centrifugation at different pH values (2.0, 7.0, and 12.0), revealed that HPH-treated cellulose limited the occurrence of coalescence phenomena and significantly slowed down gravitational separation in comparison with BM-treated cellulose. HPH-treated cellulose was responsible for the formation of a 3D network structure in the continuous phase, entrapping the oil droplets also due to the affinity with the cellulose nanofibrils, whereas BM-treated cellulose produced fibers with a more compact structure, which did adequately cover the oil droplets. HPH-treated tomato pomace gave similar results in terms of particle morphology and interfacial tension, and slightly lower emulsion stabilization capability than HPH-treated cellulose, suggesting that the used mechanical disruption process does not require cellulose isolation for its efficient defibrillation.

19 August 2021 in Polymers
Verified
Journal Article
Open access
PDF file
RCRoberta Capuano
Roberta Capuano
IBIrene Bonadies
Irene Bonadies
Rachele CastaldoRachele Castaldo
Rachele Castaldo
MCMariacristina Cocca
Mariacristina Cocca
Gennaro GentileGennaro Gentile
Gennaro Gentile
MEMaria Emanuela Errico
Maria Emanuela Errico
In this paper, a sustainable strategy to valorize and recycle heterogeneous polymer-based post-consumer waste is proposed. This strategy is based on a high-energy mechano-chemical treatment and has been applied to a polyolefin-rich fraction, coded as FIL/S, deriving from household plastic waste collection. This processing, performed in a planetary ball mill, allowed us to obtain fine grinding and, consequently, to induce an intimate mixing of the different polymer fractions and contaminants composing the FIL/S, as demonstrated by SEM analysis. As a result, an improvement in the deformability of the treated material was obtained, recording values for elongation at the break which were two and half times higher than the neat FIL/S. Finally, the addition of small amounts of organic peroxide during mechano-chemical treatment was tested, determining a more homogeneous morphology and a further improvement in mechanical parameters.

19 February 2022 in Polymers
Verified
Journal Article
Open access
PDF file
IBIrene Bonadies
Irene Bonadies
RCRoberta Capuano
Roberta Capuano
RARoberto Avolio
Roberto Avolio
Rachele CastaldoRachele Castaldo
Rachele Castaldo
MCMariacristina Cocca
Mariacristina Cocca
Maria Emanuela ErricoMaria Emanuela Errico
Maria Emanuela Errico
The sustainable management of multilayer paper/plastic waste is a technological challenge due to its composite nature. In this paper, a mechanical recycling approach for multilayer cartons (MC) is reported, illustrating the realization of thermoplastic composites based on recycled polyethylene and an amount of milled MC ranging from 20 to 90 wt%. The effect of composition of the composites on the morphology and on thermal, mechanical, and water absorption behavior was investigated and rationalized, demonstrating that above 80 wt% of MC, the fibrous nature of the filler dominates the overall properties of the materials. A maleated polyethylene was also used as a coupling agent and its effectiveness in improving mechanical parameters of composites up to 60 wt% of MC was highlighted.

5 April 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
RCRoberta Capuano
Roberta Capuano
RARoberto Avolio
Roberto Avolio
Rachele CastaldoRachele Castaldo
Rachele Castaldo
MCMariacristina Cocca
Mariacristina Cocca
GPGiovanni Dal Poggetto
Giovanni Dal Poggetto
MEMaria Emanuela Errico
Maria Emanuela Errico
Plasticized nanocomposites based on poly(lactic acid) have been prepared by melt mixing following a two-step approach, adding two different oligomeric esters of lactic acid (OLAs) as plasticizers and fumed silica nanoparticles. The nanocomposites maintained a remarkable elongation at break in the presence of the nanoparticles, with no strong effects on modulus and strength. Measuring thermo-mechanical properties as a function of aging time revealed a progressive deterioration of properties, with the buildup of phase separation, related to the nature of the plasticizer. Materials containing hydroxyl-terminated OLA showed a higher stability of properties upon aging. On the contrary, a synergistic effect of the acid-terminated plasticizer and silica nanoparticles was pointed out, inducing an accelerated hydrolytic degradation of PLA: materials at high silica content exhibited a marked brittleness and a dramatic decrease of molecular weight after 16 weeks of aging.

1 August 2025 in Polymers
Verified
Journal Article
Open access
PDF file
RCRoberta Capuano
Roberta Capuano
RARoberto Avolio
Roberto Avolio
Rachele CastaldoRachele Castaldo
Rachele Castaldo
MCMariacristina Cocca
Mariacristina Cocca
FOFederico Olivieri
Federico Olivieri
Maria Emanuela ErricoMaria Emanuela Errico
Maria Emanuela Errico
In this study, multicomponent PLA-based biocomposites were developed. In particular, both native fibrous cellulose and cellulose with modified morphology obtained through ball milling treatments were incorporated into the polyester matrix in combination with an oligomeric plasticizer, specifically a lactic acid oligomer (OLA). The resulting materials were analyzed in terms of their morphology, thermal and mechanical properties over time, water vapor permeability, and degradation under soil burial conditions in comparison to neat PLA and unplasticized PLA/cellulose composites. The cellulose phase significantly affected the mechanical properties and enhanced their long-term stability, addressing a common limitation of PLA/plasticizer blends. Additionally, water vapor permeability increased in all composites. Finally, the ternary systems exhibited a significantly higher degradation rate in soil burial conditions compared to PLA, evidenced by larger weight loss and reduction in the molecular weight of the PLA phase. The degradation rate was notably influenced by the morphology of the cellulose phase.