Chaoqun Lu

Dr. Chaoqun Lu

Beihang University

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 August 2021 in Coatings
Verified
Journal Article
Open access
PDF file
CLChaoqun Lu
Chaoqun Lu
WZWeijia Zhang
Weijia Zhang
ZJZhaoyi Jiang
Zhaoyi Jiang
YZYulong Zhang
Yulong Zhang
CNCong Ni
Cong Ni
The hole transport layer (HTL) is one of the main factors affecting the efficiency and stability of perovskite solar cells (PSCs). However, obtaining HTLs with the desired properties through current preparation techniques remains a challenge. In the present study, we propose a new method which can be used to achieve a double-layer HTL, by inserting a CuI layer between the perovskite layer and Spiro-OMeTAD layer via a solution spin coating process. The CuI layer deposited on the surface of the perovskite film directly covers the rough perovskite surface, covering the surface defects of the perovskite, while a layer of CuI film avoids the defects caused by Spiro-OMetad pinholes. The double-layer HTLs improve roughness and reduce charge recombination of the Spiro-OMeTAD layer, thereby resulting in superior hole extraction capabilities and faster hole mobility. The CuI/Spiro-OMeTAD double-layer HTLs-based devices were prepared in N2 gloveboxes and obtained an optimized PCE (photoelectric conversion efficiency) of 17.44%. Furthermore, their stability was improved due to the barrier effect of the inorganic CuI layer on the entry of air and moisture into the perovskite layer. The results demonstrate that another deposited CuI film is a promising method for realizing high-performance and air-stable PSCs.

2 November 2023 in Coatings
Verified
Journal Article
Open access
PDF file
MQMa Qiang
Ma Qiang
JGJiajun Guo
Jiajun Guo
CLChaoqun Lu
Chaoqun Lu
RZRui Zhang
Rui Zhang
XWXinjie Wang
Xinjie Wang
ZJZhaoyi Jiang
Zhaoyi Jiang
Perovskite solar cells are attracting more and more attention due to their higher absorption and low cost. However, fabricating the perovskite film with high crystallinity and ideal morphology, which presents large-size and uniform particles with fewer grain boundaries, still needs further improvement. Herein, we introduce MAPbCl3 crystals into the PbI2 film in the sequential deposition process, which obtained the controlled crystallization in perovskite films. The perovskite films induced by MAPbCl3 have stronger crystallinity, fewer defect states, and larger grain size, reducing carrier recombination and improving carrier transfer. The optimized perovskite solar cell (PSC) has achieved a power conversion efficiency of 20.97%. Furthermore, the stability of PSCs has also been enhanced due to the reduced grain boundaries impeding moisture diffusion. This strategy can be applied in other solution-based fabrication processes to improve the photovoltaic performance of PSCs.

2 September 2024 in Coatings
Verified
Journal Article
Open access
PDF file
ZJZhaoyi Jiang
Zhaoyi Jiang
JLJiaqi Li
Jiaqi Li
KLKun Li
Kun Li
RZRui Zhang
Rui Zhang
QZQin Zhenxing
Qin Zhenxing
WZWeijia Zhang
Weijia Zhang
The scalable production of high-quality perovskite thin films is pivotal for the industrialization of perovskite thin film solar cells. Consequently, the solvent system employed for the fabrication of large-area perovskite films via coating processes has attracted significant attention. In this study, a solvent system utilizing a volatile solvent as the primary reagent has been developed to facilitate the rapid nucleation of volatile compounds. While adding the liquid Lewis base dimethylformamide (DMF) can help to improve the microstructure of perovskite films, its slow volatilization renders the crystal growth process uncontrollable. Based on the solvent system containing DMF and ethanol (EtOH), introducing a small amount of NH4Cl increases the proportion of the intermediate phase in the precursor films. This not only results in a controllable growth process for the perovskite crystals but also contributes to the improvement of the film microstructure. Under the simulated illumination (AM1.5, 1000 W/m2), the photoelectric conversion efficiency (PCE) of the inverted solar cells has been improved to 20.12%. Furthermore, after 500 hours of continuous illumination, the photovoltaic device can retain 95.6 % of the initial, indicating that the solvent system is suitable for the scalable fabrication of high-quality FAPbI3 thin films.