The hole transport layer (HTL) is one of the main factors affecting the efficiency and stability of perovskite solar cells (PSCs). However, obtaining HTLs with the desired properties through current preparation techniques remains a challenge. In the present study, we propose a new method which can be used to achieve a double-layer HTL, by inserting a CuI layer between the perovskite layer and Spiro-OMeTAD layer via a solution spin coating process. The CuI layer deposited on the surface of the perovskite film directly covers the rough perovskite surface, covering the surface defects of the perovskite, while a layer of CuI film avoids the defects caused by Spiro-OMetad pinholes. The double-layer HTLs improve roughness and reduce charge recombination of the Spiro-OMeTAD layer, thereby resulting in superior hole extraction capabilities and faster hole mobility. The CuI/Spiro-OMeTAD double-layer HTLs-based devices were prepared in N2 gloveboxes and obtained an optimized PCE (photoelectric conversion efficiency) of 17.44%. Furthermore, their stability was improved due to the barrier effect of the inorganic CuI layer on the entry of air and moisture into the perovskite layer. The results demonstrate that another deposited CuI film is a promising method for realizing high-performance and air-stable PSCs.
All-inorganic CsPbBr3 perovskite solar cells have garnered extensive attention in the photovoltaic domain due to their remarkable environmental stability. Nevertheless, CsPbBr3 prepared using the conventional sequential deposition method suffers from issues such as inferior crystallinity, low phase purity, and poor film morphology. Herein, we propose a pre-crystallization methodology by introducing a minute quantity of CsBr into the PbBr2 precursor solution to generate a small amount of CsPb2Br5 crystals within the PbBr2 film, leading to a porous PbBr2 film with enhanced crystallinity. Under the influence of more pores and CsPb2Br5 crystals as nucleation sites for inducing growth, a CsPbBr3 film with a larger crystal size, lower grain boundary density, stronger crystallinity, and higher phase purity is formed. Compared with untreated devices, photovoltaic devices prepared using the pre-crystallization method achieved a champion photovoltaic conversion efficiency (PCE) of 8.62%. Furthermore, pre-crystallized devices demonstrate higher stability than untreated ones and can still retain 94% of the original PCE after being exposed to air for 1000 h without encapsulating.
Perovskite solar cells are attracting more and more attention due to their higher absorption and low cost. However, fabricating the perovskite film with high crystallinity and ideal morphology, which presents large-size and uniform particles with fewer grain boundaries, still needs further improvement. Herein, we introduce MAPbCl3 crystals into the PbI2 film in the sequential deposition process, which obtained the controlled crystallization in perovskite films. The perovskite films induced by MAPbCl3 have stronger crystallinity, fewer defect states, and larger grain size, reducing carrier recombination and improving carrier transfer. The optimized perovskite solar cell (PSC) has achieved a power conversion efficiency of 20.97%. Furthermore, the stability of PSCs has also been enhanced due to the reduced grain boundaries impeding moisture diffusion. This strategy can be applied in other solution-based fabrication processes to improve the photovoltaic performance of PSCs.
The scalable production of high-quality perovskite thin films is pivotal for the industrialization of perovskite thin film solar cells. Consequently, the solvent system employed for the fabrication of large-area perovskite films via coating processes has attracted significant attention. In this study, a solvent system utilizing a volatile solvent as the primary reagent has been developed to facilitate the rapid nucleation of volatile compounds. While adding the liquid Lewis base dimethylformamide (DMF) can help to improve the microstructure of perovskite films, its slow volatilization renders the crystal growth process uncontrollable. Based on the solvent system containing DMF and ethanol (EtOH), introducing a small amount of NH4Cl increases the proportion of the intermediate phase in the precursor films. This not only results in a controllable growth process for the perovskite crystals but also contributes to the improvement of the film microstructure. Under the simulated illumination (AM1.5, 1000 W/m2), the photoelectric conversion efficiency (PCE) of the inverted solar cells has been improved to 20.12%. Furthermore, after 500 hours of continuous illumination, the photovoltaic device can retain 95.6 % of the initial, indicating that the solvent system is suitable for the scalable fabrication of high-quality FAPbI3 thin films.
In this study, a feasible strategy is proposed for directly depositing high-quality Cu(In,Ga)Se2 (CIGS) films using Na-doped targets in a selenium-free atmosphere to boost the power conversion efficiency (PCE) of CIGS solar cells. Introducing a small amount of sodium dopant effectively promoted the textured growth of CIGS crystals in the prepared films, resulting in larger grain sizes and a smoother interface. The higher MoSe2 content at the CIGS/Mo interface increased the carrier lifetime in the films. In addition, sodium doping increased the proportion of Se atoms on the film surface and reduced the concentration of defects caused by the direct sputtering of the films in the selenium-free atmosphere. Therefore, the separation and transportation of photo-generated carriers in the devices were effectively enhanced. Using the optimized parameters, a record-high PCE of 17.26% was achieved for the 7.5% Na-doped devices, which represents an improvement of nearly 63%.
About Me
Preparation and study of high-efficiency photovoltaic thin-film materials.
Preparation and study of high-efficiency photovoltaic thin-film materials.