In this paper, series-parallel (SP) current-division will be employed for the design of very low transconductance OTAs. From the theory and measurements, it will be shown that SP mirrors allow the division of currents with division factors of thousands, without reducing matching or noise performance. SP mirrors will be applied to the design of OTAs ranging from 33 pS to a few nS, with up to 1 V linear range, consuming in the order of 100nW, and with a reduced area. An integrated 3.3-s time-constant integrator will also be presented. Several design concerns will be studied: linearity, offset, noise, and leakages, as well as layout techniques. A final comparative analysis concludes that SP association of transistors allows the design of very efficient transconductors, for demanding applications in the field of implantable electronics, among others

In this paper, the MOS transistor (MOST) moderate-inversion (MI)-weak-inversion (WI) region is shown to be the optimum design zone for CMOS 2.4-GHz common-source low-noise amplifiers (CS-LNAs) focused on low power consumption applications. This statement is supported by a systematic study where the MOST is analyzed in all-inversion regions using an exhaustive CS-LNA noise-figure (NF)-power-consumption optimization technique with power gain constraint. Effects of bias choke resistance and MOST capacitances are carefully included in the study to obtain more accurate results, especially for the MI-WI region. NF, power consumption, and gain versus the inversion region are described with design space maps, providing the designer with a deep insight of their tradeoffs. The Pareto-optimal design frontier obtained by calculation-showing the MI-WI region as the optimum design zone-is reverified by extensive electrical simulations of a high number of designs. Finally, one 90-nm 2.4-GHz CS-LNA Pareto optimal design is implemented. It achieves the best figure of merit considering under-milliwatt CS-LNAs published designs, consuming 684 μW, an NF of 4.36 dB, a power gain of 9.7 dB, and a third-order intermodulation intercept point of -4 dBm with load and source resistances of 50 Ω.

In this paper, an LC voltage-controlled oscillator (LC VCO) design optimization methodology based on the g_m/I_D tech nique and on the exploration of all inversion regions of the MOS transistor (MOST) is presented. An in-depth study of the com promises between phase noise and current consumption permits optimization of the design for given specifications. Semiempirical models of MOSTs and inductors, obtained by simulation, jointly with analytical phase noise models, allow to get a design space map where the design tradeoffs are easily identified. Four LC-VCO designs in different inversion regions in a 90-nm CMOS process are obtained with the proposed methodology and verified with electrical simulations. Finally, the implementation and measurements are presented for a 2.4-GHz VCO operating in moderate inversion. The designed VCO draws 440 μA from a 1.2-V power supply and presents a phase noise of -106.2 dBc/Hz at 400 kHz from the carrier.

In recent years there has been a growing interest in electronic design automation methodologies for the optimizationbased design of radiofrequency circuits and systems. While for simple circuits several successful methodologies have been proposed, these very same methodologies exhibit significant deficiencies when the complexity of the circuit is increased. The majority of the published methodologies that can tackle radiofrequency systems are either based on high-level system specification tools or use models to estimate the system performances. Hence, such approaches do not usually provide the desired accuracy for RF systems. In this work, a methodology based on hierarchical multilevel bottom-up design approaches is presented, where multi-objective optimization algorithms are used to design an entire radiofrequency system from the passive component level up to the system level. Furthermore, each level of the hierarchy is simulated with the highest accuracy possible: electromagnetic simulation accuracy at device-level and electrical simulations at circuit/system-level.

This paper presents a sub-μW ac-coupled reconfigurable front-end for invasive wideband neural signal recording. The proposed topology embeds filtering capabilities enabling the selection of different frequency bands inside the neural signal spectrum. Power consumption is optimized by defining specific noise targets for each sub-band. These targets take into account the spectral characteristics of wideband neural signals: local field potentials (LFP) exhibit 1/fx magnitude scaling while action potentials (AP) show uniform magnitude across frequency. Additionally, noise targets also consider electrode noise and the spectral distribution of noise sources in the circuit. An experimentally verified prototype designed in a standard 180 nm CMOS process draws 815 nW from a 1 V supply. The front-end is able to select among four different frequency bands (modes) up to 5 kHz. The measured input-referred spot-noise at 500 Hz in the LFP mode (1 Hz - 700 Hz) is 55 nV/√Hz while the integrated noise in the AP mode (200 Hz - 5 kHz) is 4.1 μ Vrms. The proposed front-end achieves sub-μW operation without penalizing other specifications such as input swing, common-mode or power-supply rejection ratios. It reduces the power consumption of neural front-ends with spectral selectivity by 6.1x and, compared with conventional wideband front-ends, it obtains a reduction of 2.5x.