The work concerns the numerical modelling of coupled thermal and mechanical phenomena occurring in the laser beam welding process. Commercial Abaqus FEA engineering software is adopted to numerical computations in order to perform a comprehensive analysis of thermo-mechanical phenomena. Created in Fortran programming language additional numerical subroutines are implemented into Abaqus solver, used to describe the power intensity distribution of the movable laser beam heat source. Temperature dependent thermomechanical properties of X5CrNi18-10 steel are adopted in the numerical analysis of stress and strain states. Mathematical and numerical models are verified on the basis of a comparison between selected results of computer simulations and experimental studies on butt-welded joints
The paper concerns the numerical analysis of the influence for three different of welding heat source inclinations on the weld pool shape and mechanical properties of the resulting joint. Numerical analysis is based on the experimental tests of single-side welding of two sheets made of X5CrNi18-10 stainless steel. The joint is made using a laser welding heat source. Experimental test was performed for one heating source inclination. As a part of the work metallographic tests are performed on which the quality of obtained joints are determined. Numerical calculations are executed in Abaqus FEA. The same geometrical model is assumed as in the experiment. Material model takes into account changing with temperature thermophysical properties of austenitic steel. Modeling of the motion of heating source is performed in additional subroutine. The welding source parameters are assumed in accordance with the welding process parameters. Numerical calculations were performed for three different inclinations of the source. One inclination is consistent with experimental studies. The performed numerical calculations allowed to determine the temperature field, shape of welding pool as well as deformations and stress state in welded joint. The obtained results are compared to results of the experiment.
The paper presents analytical methods of the prediction of mechanical properties of welded joints made of S355 steel. Formulas determining so called characteristic temperatures and times for corresponding phase transformations are used in order to build computational CCT diagrams. These empirical relationships are presented in correlation with corresponding cooling rates v8/5(t8/5). Additionally, volume fractions of each phase are determined as a function of cooling rate using analytical models. Mechanical properties of welded joints made of S355 steel are predicted on the basis of obtained phase fractions. Dilatometric research on S355 steel is performed in order to verify obtained analytical results and to evaluate the usefulness of created diagrams of austenite transformation.
1 December 2015 in Archives of Metallurgy and Materials
The work concerns the numerical modelling of structural composition and stress state in steel elements welded by a laser beam. The temperature field in butt welded joint is obtained from the solution of heat transfer equation with convective term. The heat source model is developed. Latent heat of solid-liquid and liquid-gas transformations as well as latent heats of phase transformations in solid state are taken into account in the algorithm of thermal phenomena. The kinetics of phase transformations in the solid state and volume fractions of formed structures are determined using classical formulas as well as Continuous-Heating-Transformation (CHT) diagram and Continuous-Cooling-Transformation (CCT) diagram during welding. Models of phase transformations take into account the influence of thermal cycle parameters on the kinetics of phase transformations during welding. Temporary and residual stress is obtained on the basis of the solution of mechanical equilibrium equations in a rate form. Plastic strain is determined using non-isothermal plastic flow with isotropic reinforcement, obeying Huber-Misses plasticity condition. In addition to thermal and plastic strains, the model takes into account structural strain and transformation plasticity. Changing with temperature and structural composition thermophysical parameters are included into constitutive relations. Results of the prediction of structural composition and stress state in laser butt weld joint are presented.
T-joints are often used in large-scale welded constructions. The use of a laser beam for welding allows to create joints using various techniques. Used welding method affects the shape and size of heat affected zone, deformation of welded elements and consequently the quality of the joint. This work concerns the numerical modeling of the size of heat affected zone and welding deformations in T-joint obtained with two different welding techniques: single-side fillet T-joint and butt welded T-joint, called I-core welded joint. Numerical simulations are carried out in the commercial Abaqus FEA software, supplemented by an additional numerical subroutines which enabled the analysis of thermomechanical phenomena occurring in welding process. Mathematical model of a moveable welding source and the description of heat source positioning relative to the edges of the connected elements are described in numerical subroutines. The material parameters of austenitic steel are taken into account. The size of deformations of welded joints are determined as well as the influence of two different joininig techniques of T-joint on the amount of generated welding deformations are analyzed and compared.
1 December 2015 in Archives of Metallurgy and Materials
The paper concerns the mathematical and numerical modeling of phase transformations in solid state occurring during welding. The analysis of the influence of heating rate, cooling rate and maximum temperatures of thermal cycles on the kinetics of phase transformations is presented. On the basis of literature data and experimental studies the evaluation of classic mathematical and numerical models of phase transformation is presented with respect to the advanced methods of welding by using a high speed and a high power heat source. The prediction of the structure composition in laser welded butt-joint made of S460 steel is performed, where phase transformations are calculated on the basis of modified numerical models. Temperature distributions are determined as well as the shape and size of fusion zone and heat affected zone (HAZ). Temperature field is obtained by the solution of transient heat transfer equation with convective term and external volumetric heat source taken into account. Latent heat of fusion, evaporation and heats generated during phase transformations in solid state are considered in the numerical algorithm due to the large temperature range present in analyzed process. Results of the numerical prediction of structure composition in HAZ are presented in this work. Obtained results of computer simulations are compared to experimental research performered on the laser welded joint.