Properties of Co-based alloys with high Glass Forming Ability (GFA) in the form of powder are still not widely known. However, powders of high GFA alloys are often used for the development of bulk metallic glasses by additive manufacturing. In this work Co47.6B21.9Fe20.4Si5.1Nb5% at. and Co42B26.5Fe20Ta5.5Si5Cu1% at. were developed by gas-atomization. Obtained powders in size 50–80 µm were annealed at Tg and Tx of each alloy. Then SEM observation, EDS analyses, differential thermal analysis, X-ray diffraction, nanoindentation, Mössbauer, and magnetic properties research was carried out for as-atomized and annealed states. The gas atomization method proved to be an efficient method for manufacturing Co-based metallic glasses. The obtained powder particles were spherical and chemically homogeneous. Annealing resulted in an increase of mechanical properties such as hardness and the elastic module of Co47.6B21.9Fe20.4Si5.1Nb5% at and Co42B26.5Fe20Ta5.5Si5Cu1%, which was caused by crystallization. The magnetic study shows that Co47.6B21.9Fe20.4Si5.1Nb5 and Co42B26.5Fe20Ta5.5Si5Cu1 are soft magnetic and semi-hard magnetic materials, respectively.
In this study, the influence of annealing on the phase evolution and mechanical properties of the Fe62Ni18P13C7 (at.%) alloy was investigated. Ribbons produced via melt-spinning were annealed at various temperatures, and their structural transformations and hardness were evaluated. The alloy exhibited a narrow supercooled liquid region (ΔTx ≈ 22 °C), confirming its low glass-forming ability (GFA). Primary crystallization began at approximately 380 °C with the formation of α-(Fe,Ni) and Fe2NiP, followed by the emergence of γ-(Fe,Ni) phase at higher temperatures. A significant increase in hardness was observed after annealing up to 415 °C, primarily due to nanocrystallization and phosphide precipitation. Further heating resulted in a hardness plateau, followed by a noticeable decline. Additionally, samples were produced via selective laser melting (SLM). The microstructure of the SLM-processed material revealed extensive cracking and the coexistence of phosphorus-rich regions corresponding to Fe2NiP and iron-rich regions associated with γ-(Fe,Ni).
31 May 2025 in Metallurgical and Materials Transactions A
It is well known that producing bulk metallic glasses requires very high cooling rates during processing. This limits the sizes of elements produced by casting methods and is why the alternative technology, additive manufacturing, is explored as a development method for bulk metallic glass with no geometry restrictions. Among the tested alloys with high glass ability, Co-based alloys have not yet been printed successfully. This work investigated the possibility of developing a fully amorphous sample from Co-based alloy with high glass-forming ability using selective laser melting focusing on alloy Co47.6B21.9Fe20.4Si5.1Nb5. This study contains literature analyses and experimental tests of selective laser melting (SLM). After printing, the samples were analyzed by optical microscopy, scanning electron microscopy, scanning transmission microscopy, differential thermal analysis, X-ray diffraction, and nanohardness testing. The best set of parameters was established: laser power of 65 W and scanning speed of 500 mm/s. Other parameters, constant during the experiment, were laser spot diameter of 0.11 mm, hatch spacing 77 µm, and layer thickness 25 µm. The main finding is that it is possible to develop fully amorphous samples from Co-based alloys by selective laser melting and samples printed from Co47.6B21.9Fe20.4Si5.1Nb5 are the first fully amorphous samples of Co-based alloy printed by SLM. Furthermore, an extensive discussion of the results was conducted with conclusions for further optimization of the process to enhance the quality of the samples, namely reducing the porosity and cracking phenomena. This study contributes to the area of bulk metallic glasses printing, especially in the case of a group of alloys based on cobalt.