Laser-beam fusion welding processes enable the increase of the size of metallic glass parts, and therefore facilitate the application of this new material in different products. To get exceptional properties of the material after the welding process, characteristics of the weld structure in the heat affected zone and in the fusion zone should be predicted. The main goal of this work is to study the structure and specific characteristics of the Zr55Cu30Ni5Al10 alloy after the casting process and after the laser welding process. Electron microscopy observation confirmed that the amorphous phase was present in the fusion zone and amorphous–crystalline phase was present in the heat-affected zone. Higher nanohardness and reduced Young’s modulus values were demonstrated for laser welds using higher impulse energy (2.78 J) and impulse peak power (1000 W).
Properties of Co-based alloys with high Glass Forming Ability (GFA) in the form of powder are still not widely known. However, powders of high GFA alloys are often used for the development of bulk metallic glasses by additive manufacturing. In this work Co47.6B21.9Fe20.4Si5.1Nb5% at. and Co42B26.5Fe20Ta5.5Si5Cu1% at. were developed by gas-atomization. Obtained powders in size 50–80 µm were annealed at Tg and Tx of each alloy. Then SEM observation, EDS analyses, differential thermal analysis, X-ray diffraction, nanoindentation, Mössbauer, and magnetic properties research was carried out for as-atomized and annealed states. The gas atomization method proved to be an efficient method for manufacturing Co-based metallic glasses. The obtained powder particles were spherical and chemically homogeneous. Annealing resulted in an increase of mechanical properties such as hardness and the elastic module of Co47.6B21.9Fe20.4Si5.1Nb5% at and Co42B26.5Fe20Ta5.5Si5Cu1%, which was caused by crystallization. The magnetic study shows that Co47.6B21.9Fe20.4Si5.1Nb5 and Co42B26.5Fe20Ta5.5Si5Cu1 are soft magnetic and semi-hard magnetic materials, respectively.
The work presents the structural, thermal and magnetic properties analysis of Fe72B20Si4Nb4 bulk metallic glasses in as-cast state and crystallization study of bulk amorphous alloy after annealing process. The studies were performed on bulk metallic glasses in of rods form with diameter of 1,5 and 2 mm. The structure analysis of the samples in as-cast state and phase analysis of studied alloy after annealing process was carried out by the X-ray diffraction (XRD) methods. Mössbauer spectroscopy (MS) was also used to investigate the local structure for studied bulk metallic glasses. Thermal properties associated with glass transition, onset and peak crystallization temperatures was examined by differential scanning calorimetry (DSC). The soft magnetic properties examination of tested material contained initial magnetic permeability and disaccommodation of magnetic permeability.
The materials from Fe-Co-B-Si-Nb system have several interesting and useful properties such as high mechanical strength, abrasive and corrosion resistance and good electrical properties useful in many applications, for example: materials for sensors and precise current transformers. The aim of the presented work was to obtain Fe-based alloy in an amorphous state and examination atoms arrangement in its structure which has an influence on material properties. Multicomponent alloy with nominal composition of Fe37.44Co34.56B19.2Si4.8Nb4 was obtained by pressure die casting method in form of plate with thickness of d=1mm. The structure of rapidly solidified plate was examined by X-ray diffraction. This investigation revealed that the studied sample was amorphous. Based on experimental X-ray data the pair distribution function was calculated and discussion on possible atoms arrangement was carried out.
6 July 2016 in Journal of Thermal Analysis and Calorimetry
This paper presents the structure and chosen properties of Fe-based ribbons with specified composition, after casting and heat treating. The aim of this work was to produce amorphous ribbons and study the influence of heat treatment on the structure and thermal properties before and after annealing. The base alloy ingot was prepared by induction melting of pure Fe, Co, B, Si and Nb elements in argon atmosphere. Then, the station for ultra-fast cooling of molten alloy with high vacuum pumps, designed for the production of metallic glasses in the form of ribbons by Bühler Melt Spinner SC was used. Also, the X-ray diffraction analysis system PANalytical X’Pert PRO was used. As-cast ribbons and metallic glasses after annealing were examined by differential scanning calorimetry (DSC) method, with the use of DSC822 Mettler Toledo. Annealing was done at different temperature. On the basis of obtained dependence, the glass transition temperature (Tg), onset crystallization temperature (onset—Tx) and peak crystallization temperature (peak—Tp) were determined. The supercooled liquid region (ΔTx), specific heat and the crystallization enthalpy (ΔH) were calculated as well. The microscopic observation of cross section of ribbons was carried out by means of the Zeiss Supra 35 scanning electron microscope. Based on experimental data, the discussion on the correlation between thermal properties, structure, annealing and future application was carried out.