Third-generation solar cells, including dye-sensitized solar cells, bulk-heterojunction solar cells, and perovskite solar cells, are being intensively researched to obtain high efficiencies in converting solar energy into electricity. However, it is also important to note their stability over time and the devices’ thermal or operating temperature range. Today’s widely used polymeric materials are also used at various stages of the preparation of the complete device—it is worth mentioning that in dye-sensitized solar cells, suitable polymers can be used as flexible substrates counter-electrodes, gel electrolytes, and even dyes. In the case of bulk-heterojunction solar cells, they are used primarily as donor materials; however, there are reports in the literature of their use as acceptors. In perovskite devices, they are used as additives to improve the morphology of the perovskite, mainly as hole transport materials and also as additives to electron transport layers. Polymers, thanks to their numerous advantages, such as the possibility of practically any modification of their chemical structure and thus their physical and chemical properties, are increasingly used in devices that convert solar radiation into electrical energy, which is presented in this paper.

Unsymmetrical and symmetrical azomethines were obtained using the condensation reaction of diamino-thiophene-3,4 dicarboxylic acid diethyl ester with 4-(1-pyrrolidino)benzaldehyde, fluorene-2-carboxaldehyde, 1-methylindole-3-carboxaldehyde, and benzothiazole-2-carboxaldehyde. Their thermal, optical, and electrochemical properties were investigated, and the results were supported by calculations using the density functional theory. The studied compounds melted in the range of 170–260 °C and can be converted into amorphous materials with high glass transition temperatures between 76 and 135 °C. They were thermally stable up to 220–300 °C. All imines were electrochemically active and exhibited low energy band gaps below 2 eV (except for one imine with E_g = 2.39 eV) determined on the basis of cyclic voltammetry. Most of the azomethines were emissive in solution and in the solid state. Some of them showed both S₁ (first excited state) emission and S₂ (second excited state) emission or only fluorescence from higher excited state, which is first time observed for azomethines. The imine with the most promising properties was tested in a light-emitting diode, and its ability for emission of light under external voltage was demonstrated.

In this paper, six novel symmetrical bis-(imino-1,8-naphthalimides) differing in core and N-substituent structure were synthesized, and their thermal (TGA, DSC), optical (UV-Vis, PL), electrochemical (DPV, CV) properties were evaluated. The compounds were stable to 280 °C and could be transferred into amorphous materials. Electrochemical investigations showed their ability to occur reductions and oxidations processes. They exhibited deep LUMO levels of about −3.22 eV and HOMO levels above −5.80 eV. The optical investigations were carried out in the solutions (polar and non-polar) and in films and blends with PVK:PBD. Bis-(imino-1,8-naphthalimides) absorbed electromagnetic radiation in the range of 243–415 nm and emitted light from blue to yellow. Their capacity for light emission under voltage was preliminarily tested in devices with an active layer consisting of a neat compound and a blend with PVK:PBD. The diodes emitted green or red light.

A new series of thiophene-based azomethines differing in the core structure was synthesized. The effect of the central core structure in azomethines on the thermal, optical and electrochemical properties was investigated. The obtained compounds exhibited the ability to form a stable amorphous phase with a high glass transition temperature above 100 °C. They were electrochemically active and undergo oxidation and reduction processes. The highest occupied (HOMO) and the lowest unoccupied molecular (LUMO) orbitals were in the range of −3.86–−3.60 eV and −5.46–−5.17 eV, respectively, resulting in a very low energy band gap below 1.7 eV. Optical investigations were performed in the solvents with various polarity and in the solid state as a thin film deposited on a glass substrate. The synthesized imines absorbed radiation from 350 to 600 nm, depending on its structure and showed weak emission with a photoluminescence quantum yield below 2.5%. The photophysical investigations were supported by theoretical calculations using the density functional theory. The synthesized imines doped with lithium bis-(trifluoromethanesulfonyl)imide were examined as hole transporting materials (HTM) in hybrid inorganic-organic perovskite solar cells. It was found that both a volume of lithium salt and core imine structure significantly impact device performance. The best power conversion efficiency (PCE), being about 35–63% higher compared to other devices, exhibited cells based on the imine containing a core tiphenylamine unit.

Novel oxetane-functionalized derivatives were synthesized to find the impact of carbazole substituents, such as 1-naphtyl, 9-ethylcarbazole and 4-(diphenylamino)phenyl, on their thermal, photophysical and electrochemical properties. Additionally, to obtain the optimized ground-state geometry and distribution of the frontier molecular orbital energy levels, density functional theory (DFT) calculations were used. Thermal investigations showed that the obtained compounds are highly thermally stable up to 360 °C, as molecular glasses with glass transition temperatures in the range of 142–165 °C. UV–Vis and photoluminescence studies were performed in solvents of differing in polarity, in the solid state as a thin film on glass substrate, and in powders, and were supported by DFT calculations. They emitted radiation both in solution and in film with photoluminescence quantum yield from 4% to 87%. Cyclic voltammetry measurements revealed that the materials undergo an oxidation process. Next, the synthesized molecules were tested as hole transporting materials (HTM) in perovskite solar cells with the structure FTO/b-TiO₂/m-TiO₂/perovskite/HTM/Au, and photovoltaic parameters were compared with the reference device without the oxetane derivatives.