Stripped-back representative VCSEL devices with a simple fabrication process that very closely approaches the performance of standard BCB-planarised devices have been produced. These VCSEL Quick Fabrication (VQF) devices achieve threshold currents only 0.3 mA higher than that of a standard device produced from the same material. The predictability of standard performance from VQF performance is also robustly assessed in terms of temperature effects to account for the observed disparities. These VQF devices are then processed across a 6-inch (152 mm) wafer and the resulting device-level characteristics are mapped. From this, it is apparent that there is an approximately radial decrease in oxide aperture diameter from centre to edge, found to be driven by the strain-induced wafer bow. After corrections, a residual spatial variation across the wafer remains, which, in conjunction with temperature dependent measurements, is shown to be a result of epi-material variation. By observation at 50 °C, that is, at a temperature closely resembling that of intended application, the residual centre-to-edge variation in threshold current density is found to be only 0.2 kA/cm 2 , compared to 1.3 kA/cm 2 when observing the room temperature variation of devices of nominally equivalent active volumes.
13 March 2023 in Journal of Physics D: Applied Physics
Vertical cavity surface emitting laser (VCSEL) devices and arrays are increasingly important in meeting the demands of today’s wireless communication and sensing systems. Understanding the origin of non-uniform wet thermal oxidation across large-area VCSEL wafers is a crucial issue to ensure highly reliable, volume-manufactured oxide-confined VCSEL devices. As VCSEL wafer diameters approach 200 mm, germanium (Ge) is emerging as an alternative substrate solution. To this end, we investigate the uniformity of 940 nm-emitting VCSEL performance across 150 mm diameter GaAs- and Ge-substrates, comparing the oxidation method in each case. Nominally identical epitaxial structures are used to evaluate the strain induced wafer bow for each substrate type with Ge exhibiting a reduction of over 100 μm in the peak-to-valley distortion when compared with GaAs. This wafer bow is found to be the principal cause of centre-to-edge oxidation non-uniformity when utilising a conduction-heated chuck furnace, in comparison to a convection-heated tube furnace. Using on-wafer testing of threshold current, differential resistance, and emission wavelength, device performance is demonstrated for the first time across a 150 mm Ge wafer, and is shown to be comparable to performance on GaAs substrates, when the effects of oxidation uniformity are removed. These results provide evidence that there is a realistic path to manufacturing high yield VCSELs, over wafer diameters approaching those used in Si-photonics, via Ge substrates.
19 June 2023 in Journal of Physics D: Applied Physics
InAs quantum dot ridge waveguide lasers comprising single-port multi-mode-interference-reflectors (MMIR) and single-cleaved reflectors are designed, fabricated, and characterised, to demonstrate capability for optoelectronic-integrated-circuits. Simulations of an MMIR show high values of fundamental mode reflectivity ( and good selectivity against higher order modes. Deep-etched MMIR lasers fabricated with 0.5 mm long cavities have a threshold current of 24 mA, compared to 75 mA for standard Fabry–Perot cleaved–cleaved FP-RWG lasers of the same length, both at 25 °C, and 56 mA compared to 102 mA at 55 °C. MMIR lasers exhibit stable ground state operation up to 50 °C and show promise as small footprint sources for integrated photonics.
We demonstrate high temperature operation of InAs quantum dot lasers through active region engineering. We grew an n-doped region within the InAs quantum dot (QD) layer and incorporated a 10 nm p-GaAs modulation-doped layer within a 43 nm GaAs spacer layer, both of which are essential components of the active region of the InAs QD laser device. The co-doping scheme enables the demonstration of InAs QD laser device with only seven layers of InAs QDs in the active region for high temperature operation, which is compared with a conventional undoped InAs QD laser device. A Fabry-Pérot laser device with as-cleaved facets and a co-doped InAs QD active region enables ultra-high temperature pulsed-biased O-band laser operation up to 202 °C, compared to 180 °C for conventional undoped InAs QD laser, and without requiring high-reflective facet coatings.
Emerging consumer applications of VCSEL arrays demand larger sizes and improved reliability. Significant wafer bow seen on a 150-mm GaAs-substrate wafer can impact fabrication, characterisation, and yields. It has been reported that Ge-substrates are drop-in replacements for GaAs, but also have additional benefits. We report on the spatial performance of identical 940 nm VCSELs, grown on both types of 200-mm substrate. Threshold current densities vary by 0.1μA/cm2 at the wafer centre, and a 0.78% and 0.59% decrease in centre-to-edge emission wavelengths for Ge and GaAs respectively. Results show a potential route to larger manufacturing volumes with lower costs per wafer.
Consumer applications of VCSEL arrays demand larger sizes and improved reliability. Ge-substrates are drop-in replacements for GaAs, whilst offering additional benefits. Thinner Ge-substrates are readily available due to photovoltaic supply chains, offering a cheaper cost per wafer. We report on device performance of identical 940-nm VCSELs, grown on 675µm, 500µm and 225µm thick Ge-substrates. Threshold current densities vary by less than 10μA/µm2 and 36μA/µm2 at the wafer centre between 675µm and, 500µm and 225µm respectively. A 3nm wavelength shift with decreasing substrate thickness is also observed. Results show a potential route to larger manufacturing volumes with lower cost per wafer.