Tomas Peach

Tomas Peach

Auto-generated profile, based on publicly available information

Tomas Peach

Cardiff University

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 June 2016 in Physical Review C
Verified
Journal Article
Open access
PDF file
TPT. Peach
T. Peach
UGU. Garg
U. Garg
YGY. K. Gupta
Y. K. Gupta
JHJ. Hoffman
J. Hoffman
JMJ. T. Matta
J. T. Matta
GCGianluca Colò
Gianluca Colò
Multipole strength distributions for isoscalar L≤2 transitions in Si28 have been extracted using 386-MeV inelastic α scattering at extremely forward angles, including 0∘. Observed strength distributions are in good agreement with microscopic calculations for an oblate-deformed ground state. In particular, a large peak at an excitation energy of 17.7 MeV in the isoscalar giant monopole resonance strength is consistent with the calculations.

21 December 2021 in Physical Review Materials
Verified
Journal Article
Closed access
PDF file
MMMateus G. Masteghin
Mateus G. Masteghin
VTVivian Tong
Vivian Tong
ESEleanor B. Schneider
Eleanor B. Schneider
CUCameron C. L. Underwood
Cameron C. L. Underwood
TPTomas Peach
Tomas Peach
DCDavid Cox
David Cox
The introduction of strain into semiconductors offers a well-known route to modify their band structure. Here, we show a single-step procedure for generating such strains smoothly and deterministically, over a very wide range, using a simple, easily available, highly scalable, ion implantation technique to control the degree of amorphization in and around single-crystal membranes. The amorphization controls the density of the material and thus the tension in the neighboring crystalline regions. We have demonstrated up to 3.1% biaxial tensile strain and 8.5% uniaxial strain in silicon, based on micro-Raman spectroscopy. This method achieves strain levels never previously reached in mesoscopic defect-free, crystalline silicon structures. The flexible, gently controllable, single-step process points toward very high mobility complementary metal-oxide-semiconductor devices and easy fabrication of direct-bandgap germanium for silicon-compatible optoelectronics.

13 March 2023 in Journal of Physics D: Applied Physics
Verified
Journal Article
Open access
SGSara-Jayne Gillgrass
Sara-Jayne Gillgrass
CACraig Philip Allford
Craig Philip Allford
TPT Peach
T Peach
JBJack Baker
Jack Baker
AJA D Johnson
A D Johnson
PSPeter Smowton
Peter Smowton
Vertical cavity surface emitting laser (VCSEL) devices and arrays are increasingly important in meeting the demands of today’s wireless communication and sensing systems. Understanding the origin of non-uniform wet thermal oxidation across large-area VCSEL wafers is a crucial issue to ensure highly reliable, volume-manufactured oxide-confined VCSEL devices. As VCSEL wafer diameters approach 200 mm, germanium (Ge) is emerging as an alternative substrate solution. To this end, we investigate the uniformity of 940 nm-emitting VCSEL performance across 150 mm diameter GaAs- and Ge-substrates, comparing the oxidation method in each case. Nominally identical epitaxial structures are used to evaluate the strain induced wafer bow for each substrate type with Ge exhibiting a reduction of over 100 μm in the peak-to-valley distortion when compared with GaAs. This wafer bow is found to be the principal cause of centre-to-edge oxidation non-uniformity when utilising a conduction-heated chuck furnace, in comparison to a convection-heated tube furnace. Using on-wafer testing of threshold current, differential resistance, and emission wavelength, device performance is demonstrated for the first time across a 150 mm Ge wafer, and is shown to be comparable to performance on GaAs substrates, when the effects of oxidation uniformity are removed. These results provide evidence that there is a realistic path to manufacturing high yield VCSELs, over wafer diameters approaching those used in Si-photonics, via Ge substrates.

28 August 2023 in Applied Physics Letters
Verified
Journal Article
Open access
PDF file
PAPetros Androvitsaneas
Petros Androvitsaneas
RCRachel N. Clark
Rachel N. Clark
MJMatthew Jordan
Matthew Jordan
MPMiguel Alvarez Perez
Miguel Alvarez Perez
TPTomas Peach
Tomas Peach
ABAnthony J. Bennett
Anthony J. Bennett
We have developed a process to mass-produce quantum dot micropillar cavities using direct-write lithography. This technique allows us to achieve mass patterning of high-aspect ratio pillars with vertical, smooth sidewalls maintaining a high quality factor for diameters below 2.0 μm. Encapsulating the cavities in a thin layer of oxide (Ta2O5) prevents oxidation in the atmosphere, preserving the optical properties of the cavity over months of ambient exposure. We confirm that single dots in the cavities can be deterministically excited to create high-purity indistinguishable single photons with interference visibility (0.941 ± 0.008).

28 June 2018 in Advanced Quantum Technologies
Verified
Journal Article
Closed access
PDF file
TPTom Peach
Tom Peach
KHKevin Homewood
Kevin Homewood
MLManon Lourenco
Manon Lourenco
MHMark Hughes
Mark Hughes
KSKaymar Saeedi
Kaymar Saeedi
SCSteven Clowes
Steven Clowes

22 August 2025 in IEEE Transactions on Semiconductor Manufacturing
Verified
Journal Article
Closed access
TPTomas Peach
Tomas Peach
BSBen Salmond
Ben Salmond
TJTyrone Jones
Tyrone Jones
EBElizabeth Beaumont
Elizabeth Beaumont
STStuart Thomas
Stuart Thomas
SSSam Shutts
Sam Shutts
The utilization of electron beam lithography (EBL) as a wafer scale technique for the fabrication of compound semiconductor devices provides unique challenges in terms of both application and throughput. We report on wafer scale EBL in the context of fabricating edge emitting lasers on 150 mm indium phosphide (InP) substrates. A hybrid electro-optical lithography process is used to pattern typical ridge waveguide (RWG) laser structures, while overcoming some of the practical challenges associated with fabricating these devices on large wafer platforms. This technique is demonstrated to reduce patterning times by up to a factor of 20 compared to conventional EBL processes. Moreover, we motivate the application of hybrid lithography by considering the loading effect of etching 150 mm InP wafers and the benefit of transitioning to a ‘low open area’ mask geometry.