In the past few decades, ZrN thin films have been identified as wear resistant coatings for tribological applications. The mechanical and tribological properties of ZrN thin layers depend on internal stress induced by the adopted deposition techniques and deposition parameters such as pressure, temperature, and growth rate. In sputtering deposition processes, the selected target voltage waveform and the plasma characteristics also play a crucial influence on physical properties of produced coatings. In present work, ZrN thin films, obtained setting different values of duty cycle in a reactive bipolar pulsed dual magnetron sputtering plant, were investigated to evaluate their residual stress through the substrate curvature method. A considerable progressive increase of residual stress values was measured at decreasing duty cycle, attesting the significant role of voltage waveform in stress development. An evident correlation was also highlighted between the values of the duty cycle and those of wear factor. The performed analysis attested an advantageous effect of internal stress, having the samples with high compressive stress, higher wear resistance. A downward trend for wear rate with the increase of internal residual stress was observed. The choice of suitable values of duty cycle allowed to produce ceramic coatings with improved tribological performance.
The accurate measurement of moisture content in pure gases and in gas mixtures, such as air, has great relevance in many industrial processes. In the present study, graphene oxide reduced through a mild alkaline treatment was used as a humidity sensing material to fabricate a flexible chemiresistive device operating at room temperature. The active layer was deposited by solution casting on a substrate of bimatted polyester, previously coated with inkjet-printed interdigitated electrodes made of silver. Structural investigations were performed by means of X-ray diffraction, Raman spectroscopy, and FTIR spectroscopy, while the optical properties were investigated using UV-VIS absorption and photoluminescence excitation spectroscopy. With increasing relative hu-midity from 0 to 80%, the electrical resistance decreased from about 1.4 GΩ to 2.5 MΩ. The ex-traordinarily large range of resistance values highlights the ultrahigh humidity sensitivity of re-duced graphene oxide, which acquires a fair amount of electrical conductivity after physisorption of water molecules but results in a highly resistive material in dry air. The high sensitivity at room temperature, the response’s repeatability, the wide relative humidity range detected, and the fast response time are the main advantages of the proposed humidity sensor, while the presence of some hysteresis, mainly at low relative humidity, and the recovery time need further improve-ment. Finally, the sensing mechanisms are briefly discussed.
The development of efficient sensors able to detect alcoholic compounds has great relevance in many fields including medicine, pharmaceuticals, food and beverages, safety, and security. In addition, the measurements of alcohols in air are significant for environmental protection because volatile alcohols can have harmful effects on human health not only through ingestion, but also through inhalation or skin absorption. The analysis of alcohols in breath is a further expanding area, being employed for disease diagnoses. The analyses performed by using chromatography, mass-spectrometry, nuclear magnetic resonance, ultraviolet-visible spectroscopy, Fourier-transform infrared spectroscopy, or Raman spectroscopy often require complex sampling and procedures. As a consequence, many research groups have focused their efforts on the development of efficient portable sensors to replace conventional methods and bulky equipment. The ability to operate at room temperature is a key factor in designing portable light devices suitable for in situ real-time monitoring. In the present review, we provide a survey of the recent literature on the most efficient chemiresistive materials for alcohol sensing at room temperature. Remarkable gas-sensing performances have mainly been obtained by using metal oxides semiconductors (MOSs), metal organic frameworks (MOFs), 2D materials, and polymers. Among 2D materials, we mainly consider graphene-based materials, graphitic carbon nitride, transition metal chalcogenides, and MXenes. We discuss scientific advances and innovations published in the span of the last five years, focusing on sensing mechanisms.
A flexible humidity sensor operating at room temperature was produced by direct drop casting of a graphene oxide (GO) water solution on a substrate of bimatted polyester, previously coated with inkjet-printed interdigitated electrodes in silver. The GO was synthesized by using a modified Hummers’ method, followed by an alkaline treatment with a water solution of KOH. Changes in the device resistance were measured for varying levels of relative humidity in the range from 15% to 70% in a sealed stainless cell. The device showed high sensitivity, good repeatability, and fast recovery time. Being flexible and robust, the proposed sensors could be easily integrated into wearable equipment.
Flexible sensors, with an active layer made of graphene oxide (GO), were produced to detect volatile organic compounds (VOCs) at room temperature. Copper interdigitated electrodes were inkjet-printed on a substrate of bimatted polyester, and the direct drop-casting of a GO water solution was carried out to coat the devices. The performance of both commercial GO and GO synthesized by a modified Hummers’ method was investigated and compared. The oxygenated functional groups on the GO surface mainly enhance the selective sensing of polar analytes. The fabricated sensors exhibit the highest response towards alcohols, and minor sensitivity to esters, ketones, ethers and apolar petroleum ether.
A green synthetic method was developed to produce carbon polymer dots with a high content of amino groups. A composite material, obtained dispersing the synthetized dots in the conductive polymer matrix PEDOT:PSS (Poly(3,4-EthyleneDiOxyThiophene) PolyStyrene Sulfonate), was used to fabricate a lowcost, flexible chemiresistive gas sensor for CO2 detection in the concentration range 150-3000 ppm. The sensor device showed high response and good repeatability upon CO2 exposure at room temperature with negligible responses towards CO. Being a stronger Lewis acid, the CO2 can accept lone pairs of electrons from amino groups on carbon dots surface.