The accurate measurement of moisture content in pure gases and in gas mixtures, such as air, has great relevance in many industrial processes. In the present study, graphene oxide reduced through a mild alkaline treatment was used as a humidity sensing material to fabricate a flexible chemiresistive device operating at room temperature. The active layer was deposited by solution casting on a substrate of bimatted polyester, previously coated with inkjet-printed interdigitated electrodes made of silver. Structural investigations were performed by means of X-ray diffraction, Raman spectroscopy, and FTIR spectroscopy, while the optical properties were investigated using UV-VIS absorption and photoluminescence excitation spectroscopy. With increasing relative hu-midity from 0 to 80%, the electrical resistance decreased from about 1.4 GΩ to 2.5 MΩ. The ex-traordinarily large range of resistance values highlights the ultrahigh humidity sensitivity of re-duced graphene oxide, which acquires a fair amount of electrical conductivity after physisorption of water molecules but results in a highly resistive material in dry air. The high sensitivity at room temperature, the response’s repeatability, the wide relative humidity range detected, and the fast response time are the main advantages of the proposed humidity sensor, while the presence of some hysteresis, mainly at low relative humidity, and the recovery time need further improve-ment. Finally, the sensing mechanisms are briefly discussed.
In recent years, natural graphite, widely used as anode material for commercial lithium-ion batteries (LIBs), has been classified by EU as a Strategic Raw Material (SRM) and its partial or total replacement with non-critical or end-of-life (EoL) material is recommended. Silicon is one of the most promising materials to replace natural graphite. In fact, it is known that silicon can form alloys with lithium, with a theoretical energy storage capacity at room temperature of 3579 mA h g −1 (when lithiated to Li 15 Si 4 ), i.e., significantly higher than that of graphite (372 mA h g −1 ) and comparable with metallic lithium (3860 mA h g −1 ). The limiting factor of silicon as anodic material for lithium-ion battery systems is represented by its volumetric expansion, which can reach values more than 300% during battery charge–discharge cycles, involving progressive fragmentation and loss of active material and resulting in rapid decrease of the accumulated capacity. Moreover, the recent inclusion of silicon into the EU list of strategic raw materials and the high environmental impact of silicon production from SiO 2 , make the recovery and recycling of this material thoroughly recommended, especially from EoL products like photovoltaic (PV) panels. The paper offers a state-of-the-art on challenges and solutions related to the use of silicon as anodic material in LIBs, besides a survey on the Technology Readiness Level (TRL) and the market penetration of silicon anode battery technology.
Optical characterization of composite films consisting of a ceramic matrix with embedded layered metal nanoparticles have recently received increasing interest. In particular, two methods have been mainly proposed in order to obtain optical performances of dielectric matrices containing layered nanoclusters (NCs): the first method is based on the simulation of the layered system as composed of alternated films of dielectric material and effective-medium material. Therefore, the optical response of the multilayer stack is calculated, assigning to the effective-medium layers the dielectric constant , obtained by the Yamaguchi theory, and calculating the interference between the beams reflected and refracted at each interface inside the stack. The second method considers the multilayer stack as a single-layer effective-medium film whose dielectric constant is calculated by the Maxwell Garnett (MG) theory. In particular, this second method is recognized to be valid in the case of nanoparticles uniformly distributed inside a dielectric matrix. The present study shows that the interference method, as it has been applied up to now, does not allow reproducing reflectance and transmittance spectra calculated by the MG theory in the case of a uniform distribution of NCs.
The aim of this work is to investigate the possibility of engineering desired molecular sp 2 structures in graphene oxide, via controlled oxidation of graphite powder, in order to achieve tunable chemical and microstructural properties useful for optoelectronics or sensing applications. Specifically, GO powder is obtained by a modified Hummers method, by using different concentrations of potassium permanganate (KMnO 4 ) in order to change the number of oxygen functionalities in the graphitic structure. Then, a successive alkaline treatment is performed by increasing the KOH concentration. The alkaline treatment induces a noticeable variation of the GO microstructural and chemical properties, which is accompanied by a strong enhancement of photoluminecence. PL and PLE measurements reveal that the configuration of electronic energy states changes as a function of the KMnO 4 and KOH concentration, by introducing further electronic n levels available for n→π* transitions. In particular, the number of sp 2 small domains embedded among oxygen–sp 3 domains, increases under the KOH treatment, due to the addition of OH groups. Most of these sp 2 domains are lifted-off from GO and thrown away in the surnatant giving it high blue photoluminescence excited at λ exc ∼ 319 nm. The employ of combined spectroscopy techniques allows a deep investigation of the microstructural and chemical changes induced by chemical treatments, opening the way to the fine tuning of GO functional properties.
Multilayer stacks of silver and alternate layers have been deposited by thermal evaporation on a silica substrate with the aim to obtain Ag clusters dispersed in a insulator matrix. The Ag layer thickness was approximately ; the thickness of the layer was approximately . The samples were thermally treated for a 1 h thermal annealing process at . These kinds of multilayer device also have several applications in the field of optics for the realization of antireflection coatings. However, optical characterization of dielectric matrices that contain layered metallic nanoparticles still remains an unsolved problem in the field of nanostructured optical coatings. Therefore, the surface plasmon resonance peak that appears in the optical absorption spectra because of the formation of Ag nanoclusters inside the insulator matrix has been monitored and fitted by numerical codes. In particular, a previously published theoretical model, based on the Maxwell–Garnett effective medium theory, modified to take into account the effects that are due to the particle shapes and the spatial arrangement of the clusters, has been employed to fit the optical absorption spectra.