Silane coupling agent (SCA), a kind of organic solvent, was introduced to improve the performance of coral coarse aggregates and enhance the interfacial adhesion between the inorganic coral aggregate and the cement paste of coral concrete. The crushing indicator and water absorption of the coral aggregates over various dipping times were measured, and the slump, interface microhardness, and compressive strength of coral concrete tested. The microscopic appearances of the coral concrete before and after modification were analyzed based on SEM images. The experimental results indicate that SCA can effectively reduce the crushing indicator and water absorption of coral coarse aggregates, and the modification performance becomes better over time. SCA facilitates the generation of chemical forces between the coral aggregates and cement mortars, improves adhesion between the aggregates and mortars, augments the microhardness of the interface, and increases the compressive strength. According to the microscopic appearance of the treated and untreated coral aggregate interfaces, the aggregates and the mortars are in closer combination after modification.

In this paper, an ultrahigh-strength marine concrete containing coral aggregates is developed. Concrete fabricated from marine sources is considered an effective and economical alternative for marine engineering and the construction of remote islands. To protect sea coral ecosystems, the coral aggregates used for construction are only efflorescent coral debris. To achieve the expected mechanical performance from the studied concrete, an optimal mixture design is conducted to determine the optimal proportions of components, in order to optimize the compressive strength. The mechanical properties and the autogenous shrinkage, as well as the heat flow of early hydration reactions, are measured. The hydration products fill up the pores of coral aggregates, endowing our concrete with flowability and self-compacting ability. The phases in the marine concrete are identified via X-ray diffraction analysis. The 28-day compressive and flexural strength of the developed marine concrete achieve 116.76 MPa and 18.24 MPa, respectively. On account of the lower cement content and the internal curing provided by coral aggregates, the volume change resulting from autogenous shrinkage is only 63.11% of that of ordinary reactive powder concrete.

Coral concrete has low cost and convenient materials, making it an excellent raw material for processing. However, its lower strength limits the application of coral concrete. Surface modification is expected to increase the properties of porous coral concrete. In this study, single and compound modification treatments were applied to the surface of a coral aggregate to improve its properties for promoting the mechanical performance of coral concrete. The results showed that the micro-aggregate effect and pozzolanic activity of granulated blast furnace slag (GBFS) and the permeability and polycondensation of sodium silicate (SS) could be mutually promoted. The GBFS and SS could effectively fill the pores of the coral aggregate, enhancing the properties of the aggregate, such as density and load-bearing capacity, and reducing the water absorption and crushing index by more than 50%. GBFS and SS could intensify and accelerate the hydration of cement, and generate a large number of hard hydration products at the interfacial transition zone (ITZ), which could strengthen the bonding between the aggregate and mortar, improving the strength of the ITZ. The compressive strength of the coral concrete was significantly increased.

Rolling enables the directional alignment of the reinforcements in graphene/Cu composites while achieving uniform graphene dispersion and matrix grain refinement. This is expected to achieve a breakthrough in composite performance. In this paper, the process parameters of rolling are investigated, and the defects, thickness variations of graphene and property changes of the composite under different parameters are analyzed. High-temperature rolling is beneficial to avoid the damage of graphene during rolling, and the prepared composites have higher electrical conductivity. The properties of graphene were investigated. Low-temperature rolling is more favorable to the thinning and dispersion of graphene; meanwhile, the relative density of the composites is higher in the low-temperature rolling process. With the increase of rolling deformation, the graphene defects slightly increased and the number of layers decreased. In this paper, the defect states of graphene and the electrical conductivity with different rolling parameters is comprehensively investigated to provide a reference for the rolling process of graphene/copper composites with different demands.

In this paper, two kinds of Be/2024Al composites were prepared by the pressure infiltration method using two different beryllium powders as reinforcements and 2024Al as a matrix. The effect of interfacial strength on the mechanical behavior of Be/2024Al composites was studied. Firstly, the microstructure and mechanical properties of the two composites were characterized, and then the finite element analysis (FEA) simulation was used to further illustrate the influence of interfacial strength on the mechanical properties of the two Be/2024Al composites. The mechanical tensile test results show that the tensile strength and elongation of the beryllium/2024Al composite prepared by the blocky impact grinding beryllium powder (blocky-Be/2024Al composite) are 405 MPa and 1.58%, respectively, which is superior to that of the beryllium/2024Al composite prepared by the spherical atomization beryllium powder (spherical-Be/2024Al composite), as its strength and elongation are 331 MPa and 0.38%, respectively. Meanwhile, the fracture of the former shows brittle fracture of beryllium particles and ductile fracture of aluminum, while the latter shows interface debonding. Further FEA simulation illustrates that the interfacial strength of the blocky-Be/2024Al composite is 600 MPa, which is higher than that of the spherical-Be/2024Al composite (330 MPa). Therefore, it can be concluded that the better mechanical properties of the blocky-Be/2024Al composite contribute to its stronger beryllium/aluminum interfacial strength, and the better interfacial strength might be due to the rough surface and microcrack morphology of blocky beryllium particles. These research results provide effective experimental and simulation support for the selection of beryllium powder and the design and preparation of high-performance beryllium/aluminum composites.

In this paper, the effects of carbon nanotube defects and a copper surface oxide layer on a carbon nanotube–copper interface were studied via first-principles. A defect-free CNT-Cu interface, Stone–Wales defect CNT-Cu interface, single-hole and double-hole defect CNT-Cu interface, and Cu₂O-Cu interface were simulated and calculated. By simulating the differential charge density, atomic population, bond population and density of states of the interface model, the effects of various defects on the interface bonding and electrical conductivity of the composites during the preparation of the CNT-reinforced copper matrix composites were analyzed, which provided theoretical guidance for the preparation of CNT/Cu composites. After that, copper matrix composites with different CNT defect contents were prepared via different rolling deformation processes. Their hardness and electrical conductivity were tested, and the results were consistent with the results obtained via the first-principles calculations.