Ivan Gabrijel

Dr. Ivan Gabrijel

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
IGIvan Gabrijel
Ivan Gabrijel
MRMarija Jelcic Rukavina
Marija Jelcic Rukavina
Nina StirmerNina Stirmer
Nina Stirmer
This paper presents the results of an experimental study aimed at determining the influence of wood fly ash (WFA) from three Croatian power plants on the properties of concrete. First, the chemical and physical properties of WFA’s were determined. It was found that these properties are highly influenced by combustion technology, the type and parts of wood used as fuel, and the local operating conditions. Subsequently, workability, heat of hydration, stiffness development, 28-day compressive strength, apparent porosity, and capillary absorption were determined on concrete mixes prepared with WFA as cement replacement from 5–45% by weight. Cement replacement up to 15% with the finest WFA accelerated hydration, stiffness development, and increased compressive strength of concrete up to 18%, while replacement with coarser WFA’s led to a decrease in compressive strength of up to 5% and had more gradual heat liberation. The dominant effect that could explain these findings is attributed to the filler and filling effect mechanisms. At the same time replacement content of up to 45% had very little effect on capillary absorption and could give concrete with sufficiently high compressive strength to be suitable for construction purposes.

17 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
MRMarija Jelcic Rukavina
Marija Jelcic Rukavina
IGIvan Gabrijel
Ivan Gabrijel
IGIvanka Netinger Grubeša
Ivanka Netinger Grubeša
Ana MladenovicAna Mladenovic
Ana Mladenovic
This paper presents an experimental investigation of the compressive behavior of high-strength self-compacting concrete exposed to temperatures up to 600 °C. Ten different concrete compositions were tested, in which part of the cement (by weight) was replaced by three different mineral additives (5–15% metakaolin, 20–40% fly ash and 5–15% limestone). The stress–strain curves, compressive strength, modulus of elasticity and strain at peak stress were evaluated from uniaxial compression tests. Scanning electron microscope micrographs were also taken to evaluate the damage caused by the high temperatures. A sharp decrease in mechanical properties and an increase in peak strain were observed already after 200 °C for all mixes tested. The different mineral additives used in this study affected the variations of residual compressive strength by 24% and peak strain by 38%, while the variations of residual modulus elasticity were 14%. Comparing the obtained results with the recommendations for compressive strength given in regulatory code EN 1992-1-2 for high strength concrete, it can be concluded that the strength loss observed in EN 1992-1-2 at temperatures up to 400 °C is too conservative. The Popovics model for the relationship between stress and strain provided a good approximation for the experimentally determined stress–strain curves at different temperatures.

14 December 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
IGIvan Gabrijel
Ivan Gabrijel
MSMarijan Skazlić
Marijan Skazlić
Nina StirmerNina Stirmer
Nina Stirmer
Wood biomass is widely used in the European Union as a fuel for the production of heat and electrical energy, generating a considerable amount of ash. The disposal of ash, especially its finest fraction, requires proper engineering solutions, since these particles contain heavy metals and can easily pollute soil, groundwater, or air. In this work, wood fly ash with a high amount of pozzolanic oxides and one with a high CaO content were used in concrete as a 15% and 30% cement replacement. Incorporation of wood ash in concrete reduced the 28-day compressive strength of concrete by up to 37%, which was attributed to the low stiffness of the wood ash particles, while the 2-year compressive strength indicated very low pozzolanic reactivity. The capillary absorption of concrete increased with the increase in the ash content, but almost no influence on the gas permeability was observed. Wood fly ash with high CaO content reduced the drying shrinkage of concrete by up to 65% after 1 year. In a mix with 30% of high CaO fly ash, swelling occurred in the first days of hydration, which was attributed to the volume expansion due to the formation of portlandite and brucite, but did not lead to cracking or a decrease in long-term compressive strength.

19 February 2020
Verified
Book Chapter
Closed access
PDF file
IGIvan Gabrijel
Ivan Gabrijel
SSStéphanie Staquet
Stéphanie Staquet
MKMarkus Krüger
Markus Krüger
JCJérome Carette
Jérome Carette
CGChristian U. Grosse
Christian U. Grosse
GTGregor Trtnik
Gregor Trtnik

2 March 2020 in Construction and Building Materials
Verified
Journal Article
Closed access
Marijana SerdarMarijana Serdar
Marijana Serdar
SSStéphanie Staquet
Stéphanie Staquet
DSDirk Schlicke
Dirk Schlicke
EREmmanuel Rozière
Emmanuel Rozière
Miguel AzenhaMiguel Azenha
Miguel Azenha
Aljoša ŠajnaAljoša Šajna
Aljoša Šajna

17 June 2015 in Journal of Structural Fire Engineering
Verified
Journal Article
Closed access
MRMarija Jelcic Rukavina
Marija Jelcic Rukavina
DBDubravka Bjegovic
Dubravka Bjegovic
IGIvan Gabrijel
Ivan Gabrijel
This paper presents an experimental research on the performance of high-strength selfcompacting concrete (SCC) with different mineral additives after exposure to high temperatures of up to 600°C. For this purpose, four SCC mixtures were studied: one reference and three mixtures where the Portland cement was replaced with mineral additive (fly ash, metakaolin and limestone) in certain proportions. After natural cooling in the furnace, compressive strength and static modulus of elasticity were determined and compared to results obtained from other studies and those provided in EN 1992-1-2 and EN 1994-1-2 for normal-vibrated concrete. Additionally, acoustic emission (AE) parameters during compression test of heated and unheated specimens were also obtained which showed good non-destructive tool for identifying exposure temperature of the concrete needed for the assessment of concrete structures after fire.