Objective: The cast-in-place steel spring floating slab track (SSFST) is difficult to maintain and repair, while the mechanical strength of the end of the traditional prefabricated SSFST is poor. In order to overcome the above shortcomings, a shear-hinge-combined prefabricated SSFST was developed, and an indoor test was carried out to analyze its vibration-damping effect. Methods: A combined shear hinge SSFST connection model with two length sizes was established. The dynamic response amplitude and frequency response characteristics of the foundation (ground) under different isolator installations and fatigue loads were studied, and the vibration-damping performance of two sizes of combined shear hinge SSFST was evaluated. Results: The vibration-damping effect of the steel spring vibration isolator mainly acts in the middle and low-frequency bands of 16–400 Hz, and the vibration near 10 Hz will be aggravated after the vibration isolator is installed. The vibration index and variation law of the two sizes of SSFST are similar, and the vibration response of 4.8 m SSFST is slightly less than 3.6 m SSFST. There is almost no change in each index when the load is 5 million times, and there is a certain range of change when the load is 10 million times, but the overall change is small. Conclusions: The combined shear hinge prefabricated SSFST can have an excellent isolation effect on vibration and can still maintain good vibration-damping ability within 10 million fatigue loads (about 5 years); 4.8 m SSFST should be laid in straight sections with higher train speeds, while 3.6 m SSFST should be applied in curved sections to ensure smooth lines.
To meet the transportation requirements of heavy-haul trains, it is necessary to consider the use of prestressed reinforced concrete ballastless tracks. Therefore, the CRTSIII SBT (China Railway Track System III-type slab ballastless track) has been considered for its convenient construction and geometric adjustment. Considering the problems existing in the base plate of CRTSIII SBT in heavy-haul applications, an indoor test and simulation were conducted to explore the cracking phenomenon of the base plate concrete under fatigue load. The reliability of the simulation was verified through the experimental results. A fatigue crack development law of the base plate structure was established. Furthermore, the influence of the load position, the thickness of self-compacting concrete and axle loads on the fatigue damage of the base plate structure were investigated. For the CRTSIII SBT subjected to heavier axle loads, it is appropriate to thicken the self-compacting concrete layer and strengthen the concrete and steel reinforcement at the plate end to reduce fatigue damage and cracks. The research results can serve as a basis for the optimization of the CRTSIII SBT base plate structure in heavy-haul railway applications.
1 August 2020 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Compared with ordinary railways, the curve radius of tram lines tends to be smaller, with minimum values of only 30 m. Therefore, wheel–rail interaction is more intense and complicated in sections of small radius tram line curves. Using a stochastic variable sample set based on a generalized probability density evolution method, the stochastic variable–spectrum representation method was used to generate a time-domain sample set of stochastic track irregularities. By inputting the stochastic set of track irregularities into a tram-track coupled dynamic system model, the stochastic dynamic response of the coupled dynamic system can be obtained. Moreover, by substituting the stochastic dynamic system response into the generalized probability density evolution formula, the process of probability density evolution of each evaluation index can be obtained by the finite difference method. Finally, the dynamic response of the tram-track coupled dynamic system can be evaluated by the probability distribution of each index. By setting a series of specific groove rail wear values, a tram-track coupled dynamic analysis was carried out, and compared with the specification requirements, vehicle safety limits under different wear values were obtained. This research has great engineering value for guiding the routine maintenance of small radius curve sections of trams.
Background: In order to study the applicability of Low Vibration Track (LVT) in heavy-haul railway tunnels, this paper carried out research on the dynamic effects of LVT heavy-haul railway wheels and rails and provided a technical reference for the structural design of heavy-haul railway track structures. Methods: Based on system dynamics response sensitivity and vehicle-track coupling dynamics, the stability of the upper heavy-haul train, the track deformation tendency, and the dynamic response sensitivity of the vehicle-track system under the influence of random track irregularity and different track structure parameters were calculated, compared and analyzed. Results: Larger under-rail lateral and vertical structural stiffness can reduce the dynamic response of the rail system. The vertical and lateral stiffness under the block should be set within a reasonable range to achieve the purpose of reducing the dynamic response of the system, and beyond a certain range, the dynamic response of the rail system will increase significantly, which will affect the safety and stability of train operation. Conclusions: Considering the changes of track vehicle body stability coefficients, the change of deformation control coefficients, and the sensitivity indexes of dynamic performance coefficients to track structure stiffness change, the recommended values of the vertical stiffness under rail, the lateral stiffness under rail, the vertical stiffness under block, and the lateral stiffness under block are, respectively 160 kN/mm, 200 kN/mm, 100 kN/mm, and 200 kN/mm.
Purpose: Steel-spring-floating slab tracks are widely used in subway lines. It is necessary to analyze and study the vibration damping and transmission characteristics of the steel-spring-floating slab track in various frequency bands under the action of train loads. Method: A steel-spring-floating slab track and ordinary monolithic track tunnel sites with similar line conditions on straight and curved segments were selected. The vibration signals of rail, track bed, and tunnel walls were collected and the analysis results of vibration damping and vibration transmission between the steel-spring-floating slab track and the ordinary monolithic track were compared. Results: The dynamic responses of the rail in the four working conditions are relatively close, and the acceleration of the steel-spring-floating slab track bed is significantly larger than that of the ordinary monolithic track. The vibration response generated in the curved segment is significantly greater, and each frequency band will generate more peak points, and the high-frequency vibration will be more severe. Conclusions: The steel-spring-floating slab track can significantly reduce the acceleration response of the tunnel wall; the bottom constraint of the steel-spring-floating slab track is less, and the vibration response of the track bed is more severe.
In view of the problems present in the construction process of the embedded track structure of modern tram, we have designed a Novel Fastener Type Ballastless Track (NFTBT) for tram. To optimize the size of the NFTBT’s structure, the finite element model of the NFTBT’s structure in the tram running stage is built, the mechanical characteristics of the NFTBT’s structure are calculated, and the geometric parameters of the NFTBT’s structure are systematically studied. The research results are as follows: (1) As the size of the track slab increases, the displacement differences of the middle part of the NFTBT are similar, and the size of the track slab has little effect on the displacement. (2) The stress difference of the NFTBT’s structure under the different distances between the centers of the adjacent grouting holes’ conditions is small. Although a larger distance between the centers of the adjacent grouting holes can reduce the number of grouting holes in the track slab, the distance should not be too large to reduce the peak stress at the bottom of the NFTBT. (3) When the distance between the adjacent fasteners of the NFTBT changes within a certain range, the rail is greatly affected by the uneven settlement of the subgrade, and the track irregularity will be aggravated. (4) The NFTBT does not require the implementation of cable passages at intervals, which facilitates the passage and fixation of the cables in the tram operation section and can reduce the difficulty of adjusting the geometry of the track structure, thus accelerating the construction progress.