Jelena Mitrić

Dr. Jelena Mitrić

Laboratory for Electronic Materials, Solid State Physics Department, Institute of Physics Belgrade, Pregrevica 118, 11080 Belgrade, Serbia
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 February 2019 in Journal of Raman Spectroscopy
Verified
Journal Article
Closed access
PDF file
Jelena MitrićJelena Mitrić
Jelena Mitrić
URUroš Ralević
Uroš Ralević
MMMiodrag Mitrić
Miodrag Mitrić
JĆJovana Ćirković
Jovana Ćirković
GKGregor Križan
Gregor Križan
NRNebojsa Romcevic
Nebojsa Romcevic

8 August 2019 in Journal of Raman Spectroscopy
Verified
Journal Article
Closed access
PDF file
JRJasna L. Ristic-Djurovic
Jasna L. Ristic-Djurovic
LILeunam Fernandez Izquierdo
Leunam Fernandez Izquierdo
Branka HadžićBranka Hadžić
Branka Hadžić
LJLinnavel Jiménez‐Hernández
Linnavel Jiménez‐Hernández
ADAlicia M. Díaz‐García
Alicia M. Díaz‐García
NRNebojsa Romcevic
Nebojsa Romcevic

5 August 2022 in Chemosensors
Verified
Journal Article
Open access
PDF file
GJGediminas Jakubauskas
Gediminas Jakubauskas
MGMartina Gilic
Martina Gilic
EPEdita Paluckiene
Edita Paluckiene
Jelena MitrićJelena Mitrić
Jelena Mitrić
JCJovana Cirkovic
Jovana Cirkovic
Neringa PetrasauskieneNeringa Petrasauskiene
Neringa Petrasauskiene
Thin copper selenide films were synthesized on polyamide sheets using the successive ionic layer adsorption and reaction (SILAR) method at three different temperatures. It was found that elevating the temperature of the solution led to the creation of copper selenide films with different features. X-ray diffraction characterization revealed that all films crystallized into a cubic Cu2−xSe, but with different crystallinity parameters. With elevating the temperature, grain size increased (6.61–14.33 and 15.81 for 40, 60 and 80 °C, respectively), while dislocation density and the strain decreased. Surface topology was investigated with Scanning Electron Microscopy and Atomic Force Microscopy, which revealed that the grains combined into agglomerates of up to 100 nm (80 °C) to 1 μm (40 °C). The value of the direct band gap of the copper selenide thin films, obtained with UV/VIS spectroscopy, varied in the range of 2.28–1.98 eV. The formation of Cu2−xSe was confirmed by Raman analysis; the most prominent Raman peak is located at 260 cm−1, which is attributed to binary copper selenides. The thin Cu2−xSe films deposited on polyamide showed p-type conductivity, and the electrical resistivity varied in the range of 20–50 Ω. Our results suggest that elevated temperatures prevent large agglomeration, leading to higher resistance behavior.

30 December 2024 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
SJStefan T. Jelić
Stefan T. Jelić
JĆJovana Ćirković
Jovana Ćirković
JJJelena Jovanović
Jelena Jovanović
TNTatjana Novaković
Tatjana Novaković
MPMatejka Podlogar
Matejka Podlogar
ZBZorica Branković
Zorica Branković

1 October 2021 in Physica E: Low-dimensional Systems and Nanostructures
Verified
Journal Article
Closed access
Jelena MitrićJelena Mitrić
Jelena Mitrić
NPNovica Paunovic
Novica Paunovic
MMM. Mitrić
M. Mitrić
JĆJ. Ćirković
J. Ćirković
MGMartina Gilic
Martina Gilic
NRNebojsa Romcevic
Nebojsa Romcevic

14 November 2025 in Materials
Verified
Journal Article
Open access
PDF file
NŽNikola Živković
Nikola Živković
SVStefan Vulović
Stefan Vulović
Milos Milan LazarevicMilos Milan Lazarevic
Milos Milan Lazarevic
ABAnja Baraba
Anja Baraba
Aleksandar JakovljevićAleksandar Jakovljević
Aleksandar Jakovljević
ALAleksandra Milić Lemić
Aleksandra Milić Lemić
Advances in additive manufacturing have accelerated the development of 3D-printed dental resin composites. These materials contain a higher proportion of organic matrix and less filler than light-cured representatives, which may affect their behavior in the oral environment. This study aimed to evaluate the biological and chemical properties of 3D-printed dental resin composites before and after artificial aging, and to compare them with the light-cured representative. Specimens from a light-cured composite (Omnichroma—OMCR) and two 3D-printed composites (GT Temp PRINT—GTPR; SprintRay CROWN—SPRY) were subjected to aging treatments: unaged (T0) or thermocycled for 5000 (T1) and 10,000 cycles (T2). Biological evaluation was performed using MTT assay and Live/Dead cell fluorescence microscopy using human gingival fibroblasts, whereas Raman spectroscopy analysed materials’ structural changes. Materials exhibited good biocompatibility (>70% cell viability), with OMCR displaying greater variability. OMCR was more susceptible to chemical degradation under thermal stresses than both 3D-printed materials. Tested 3D-printed composites can provide comparable or even superior biological and chemical properties compared to light-cured representative, likely due to optimized resin formulations and post-curing protocols that improve polymer network organization and reduce residual monomer release. These findings support the potential of tested 3D-printed composites for manufacturing dental restorations.