Background: Despite advances in understanding various risk and prognostic factors, spontaneous intracerebral hemorrhage is connected to very high morbidity and mortality, while the therapy is mainly supportive. Understanding of the pathophysiology of initial hematoma expansion is limited due to insufficient clinical data and lack of a suitable animal model. Methods: We injected 40 anatomic specimens of the basal ganglia with contrast medium, scanned them with a micro-computed tomography scanner and analyzed the results of radiological studies, direct and histological examinations. Results: In 9 cases, micro-computed tomography and histological examinations revealed contrast medium extravasations mimicking intracerebral hematomas. The artificial hematomas spread both proximally and distally along the ruptured perforator and its branches in the perivascular spaces and detached the branches from the adjacent neural tissue leading to destruction of the tissue and secondary extravasations. Moreover, some contrast extravasations skipped to the perivascular spaces of unruptured perforators, created further extravasation sites and aggravated the expansion of the artificial hematoma. There was no subarachnoid extension of any artificial hematoma. Conclusions: We postulate that a forming basal ganglia intracerebral hematoma spreads initially in the perivascular space, detaches the branches from the neural tissue and causes secondary bleeding. It can also skip to the perivascular space of a nearby perforator. The proposed mechanism of hematoma initiation and formation explains extent of damage to the neural tissue, variability of growth in time and space, creation of secondary bleeding sites, and limited usefulness of surgical interventions. The model is reproducible, the extent of the artificial hematoma can be easily controlled, the rupture sites of the perforating arteries can be determined, and preparation of the model does not require specialized, expensive equipment apart from the micro-computed tomography scanner.

Pollutant properties in intake air to internal combustion engines were analyzed. Mineral dust particles’ influence on accelerated engine components’ wear was discussed. Dust concentration values in the air under various operating conditions in trucks and special vehicles were presented. The idea and necessity for using two-stage filters, operating in a “multi-cyclone–porous partition” system for vehicles operated in dusty air conditions, are presented. Information from the literature information has been presented, showing that impurities in small grain sizes reduce fiber bed absorbency. It has been shown that such a phenomenon occurs during filter material operation, located directly behind the inertial filter (multi-cyclone), which off-road vehicles are equipped with. It results in a greater pressure drop intensity increase and a shorter proper filter operation period. It has been shown that filter material selection for the motor vehicle air filter requires knowledge of the mass of stopped dust per filtration unit area (dust absorption coefficient k_m) determined for a given permissible resistance value Δp_fdop. It has been shown that there is no information on absorption coefficient values for filter materials operating in a two-stage “multi-cyclone–porous partition” separation system. Original methodology and conditions for determining dust absorption coefficient (k_m) of a separation partition, operating under the conditions of two-stage filtration, were presented. The following characteristics were tested: separation efficiency, filtration performance, and pressure drop characteristics of three different filtration partitions. These were A (cellulose), B (cellulose and polyester), and C (cellulose, polyester, and nanofibers layer), working individually and in a two-stage system—behind the cyclone. Granulometric dust composition dosed into the cyclone and cyclone downstream was determined. During tests, conditions corresponding to air filter’s actual operating conditions, including separation speed and dust concentration in the air, were maintained. For the pressure drop values, the dust absorption coefficient (k_m) values of three different filtration partitions (A, B, and C), working individually and in a two-stage system—behind the cyclone—were determined experimentally.

This work aimed to assess the impact of acellularization and sterilization methods on the mechanical properties of biocomposites used as a skin substitute. On the basis of the statistical analysis, it was ascertained that the values of the Young modulus for the samples before the sterilization process—only in the cases of substances such as: trypsin, 15% glycerol and dispase—changed in a statistically significant way. In the case of dispase, the Young modulus value before the sterilization process amounted to 66.6 MPa, for trypsin this value equalled 33.9 MPa, whereas for 15% glycerol it was 11 MPa. In the case of samples after the completion of the sterilization process, the analysis did not show any statistically significant differences between the obtained results of Young’s modulus depending on the respective reagents applied. It was confirmed that different methods of acellularization and the process of sterilization effect the alteration of mechanical properties of allogeneic skins. In the case of the decellularization method using SDS (Sodium Dodecyl Sulfate), liquid nitrogen and 85% glycerol the highest values of strain were observed. In the authors’ opinion, it is the above-mentioned methods that should be recommended in the process of preparation of skin substitutes.