Lenka Bujdáková Konečná

Dr. Lenka Bujdáková Konečná


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 September 2022 in Designs
Verified
Journal Article
Open access
PDF file
OIOľga Ivánková
Oľga Ivánková
OHOlga Hubova
Olga Hubova
MMMarek Macák
Marek Macák
EVEva Vojteková
Eva Vojteková
LKLenka Bujdáková Konečná
Lenka Bujdáková Konečná
The investigation of wind pressure distribution on a façade of an atypically shaped 162 m tall building is discussed in this paper. The horizontal cross-section was changed with the height of the structure (the square in the bottom part and the polygon in the top). The surface of the structure was smooth. A structural system was created using a combination of the tube structural system and exoskeleton structure. The building was stand-alone, located in urban terrain. In this case, the information in standards were not sufficient for its design. Therefore, other available tools had to be used for the determination of required input parameters (mean external pressure coefficients). At first, wind tunnel tests (WT) were performed on a reduced-scale model (1:300). Then, the obtained results were compared with data from a computational fluid dynamics (CFD) simulation. The accuracy of the simulation was evaluated by the method of three metrics. Short descriptions of the reduced-scale model, boundary layer wind tunnel, used measuring devices, and the methodology of tests are mentioned. The aim of this research was to identify the influence of the shape modification on the values of mean external pressure coefficients (in the comparison with the original shape, which was the cuboid). In the case of the cuboid, good agreement between the values determined by the CFD and the values from Eurocode was achieved. Larger discrepancies occurred on the roof. The modification of the total shape of the structure from the cuboid to atypical structure had the positive effect on the mean values of external pressure coefficients cpe. These values were smaller (at some levels significantly). Mainly, this effect was noticeable on the leeward side. For the wind directions 0° and 180°, the changes of the values were relatively large. For the other two wind directions (45° and 67.5°), the values on the windward sides were similar. The large advantage of this atypical structure is that the negative pressures on side walls and leeward side are smaller in the comparison with the cuboid. This is very useful for the fixing of façade components, where the values of negative pressures are larger than the positive pressures on the cladding in the larger heights.

10 January 2023 in Buildings
Verified
Journal Article
Open access
PDF file
OHOlga Hubova
Olga Hubova
MMMarek Macák
Marek Macák
MFMichal Franek
Michal Franek
PLPeter Lobotka
Peter Lobotka
LKLenka Bujdáková Konečná
Lenka Bujdáková Konečná
OIOľga Ivánková
Oľga Ivánková
This article deals with the investigation of wind effects on a façade of a rectangular residential building with explicit modelling of the windows for specific wind conditions. The external wind pressure coefficients were treated on the façade and at the places of the window sills, linings, and lintel for the direction of the wind from 0° to 90° with increments of 22.5°. For a detailed analysis, the CFD simulation using Ansys Fluent was used. The method selected for the CFD simulation solution and its setting (quality of meshing, horizontal homogeneity of the boundary layer, etc.) were verified by known results of similar objects. The purpose of this analysis is to show how important it is to consider wind effects to determine the suitable placement of passive ventilation devices. Research shows the potential optimal position of ventilation units in terms of favourable pressure distribution. Zones with negative pressure and corners or façades in a wake are not suitable for applying passive ventilation units. The results can serve as a basis for designers to achieve optimal comfort in residential buildings.

1 December 2015 in Transactions of the VŠB – Technical University of Ostrava, Civil Engineering Series
Verified
Journal Article
Open access
PDF file
JKJuraj Králik
Juraj Králik
OHOlga Hubova
Olga Hubova
LKLenka Bujdáková Konečná
Lenka Bujdáková Konečná
A Computer-Fluid-Dynamic (CFD) simulation of air-flow around quarter-circular object using commercial software ANSYS Fluent was used to study iteration of building to air-flow. Several, well know transient turbulence models were used and results were compared to experimental measurement of this object in Boundary Layer Wind Tunnel (BLWT) of Slovak University of Technology (SUT) in Bratislava. Main focus of this article is to compare pressure values from CFD in three different elevations, which were obtained from experimental measurement. Polyhedral mesh type was used in the simulation. Best results on the windward face elevations were obtained using LES turbulence model, where the averaged difference was around 7.71 %. On the leeward face elevations it was SAS turbulence model and averaged differences from was 15.91 %. On the circular face it was SAS turbulence model and averaged differences from all elevations was 12.93 %.

29 October 2023 in Buildings
Verified
Journal Article
Open access
PDF file
OHOlga Hubova
Olga Hubova
MMMarek Macák
Marek Macák
MFMichal Franek
Michal Franek
OIOľga Ivánková
Oľga Ivánková
LKLenka Bujdáková Konečná
Lenka Bujdáková Konečná
The design of a 69 m tall multipurpose building was investigated in this paper. The shape of the structure above the ground was an elliptical cylinder. Under the ground, the building was extended into a cuboid shape (for car parking). External wind pressure coefficients were determined using three methods: wind tunnel tests, CFD, and “the simplification of the shape” (using information defined in building standards). From the obtained results, it was evident that the simplification did not provide results with sufficient accuracy. The external wind pressure coefficients presented in this paper should be used for the design of a similar structure. The shape of the elliptical cylinder is very sensitive to applied wind. Positive pressures only occur on a small area of the windward side. The rest of the windward side is loaded with negative pressures. Therefore, torsional effects can occur, and these can be dangerous for the structure. The leeward side is completely loaded with negative pressures. In our case, this information was necessary for a follow-on static and dynamic analysis of the building. Various subsoil stiffness coefficients were considered. The calculated horizontal displacement was compared with the limit value. A measured wind direction of 20° caused the maximum obtained torsional moment, and a wind direction of 90° induced the maximum obtained force. The commercial program Ansys Fluent 2022 was used for the CFD simulation. The SCIA ENGINEER 21 program was used for follow-on analysis. This paper presents brief information on the selected turbulence model and details the settings used for the CFD simulation. Also, a description of the wind tunnel laboratory utilized in this study is provided, along with a description of the measuring devices used and the methodologies of the tests carried out. The main purpose of this paper is to show how important it is to consider the wind load for the static analysis of a structure like this.

1 September 2011 in Slovak Journal of Civil Engineering
Verified
Journal Article
Closed access
Milan SokolMilan Sokol
Milan Sokol
LKLenka Bujdáková Konečná
Lenka Bujdáková Konečná
MČM. Čuhák
M. Čuhák
MDM. Dallemule
M. Dallemule
Very low seismicity areas in Slovakia and comparison of seismic risk in Central European CountriesA parametric study concerning the importance of very low seismicity for Slovakia is introduced. Analyses were performed for ordinary buildings such as family houses, residential brick buildings, residential panel buildings and high-rise buildings. Both horizontal wind and seismic actions were analysed and compared in detail for all the regions and conditions in Slovakia.