In 2013, the EUROfusion organization launched the pre-conceptual design studies of the fusion DEMO tokamak. Sev-eral options of superconducting magnet design are investigated within the scope of the project. The magnets based on $\rm Nb_{3}Sn$ , namely the Toroidal Field (TF) and Central Solenoid (CS) coils, can be made either using the Wind and React technology, as in ITER, or React and Wind (RW) technology with potentially significant cost-saving benefits. Within the R and D program of the Swiss Plasma Center, the first full-size DEMO TF RW conductor prototype, RW1, was manufactured and tested in 2015-2016. The second, im-proved prototype, RW2, was built and tested in 2017-2018. The ex-perimental results collected over several test campaigns performed on four assemblies of RW2 rated for 63 kA at 12.23 T are present-ed. The current sharing temperature $T_{cs}$ of the latest RW2 assem-bly in DEMO operating conditions reached 7.16 K after 1000 elec-tromagnetic cycles and four thermal cycles. This $T_{cs}$ corresponds to the effective strain $\epsilon_{\rm eff} = -0.27 %$ , significantly exceeding the design requirement of $T_{cs}\geq 6.7 {\rm K}$ . If RW2 have been used in ITER TF coils, the $T_{cs}$ at 68 kA and 10.9 T would be 7.42 K, i.e. approximate-ly 1 K higher than most of the ITER TF samples, and that with on-ly 55 % of $\rm Nb_{3}Sn$ used in ITER TF conductor. The tests of RW2 proved that the cost-saving potential of the React and Wind technolo-gy is enormous.
26 March 2021 in IEEE Transactions on Applied Superconductivity
A Nb 3 Sn based, React&Wind flat cable, named RW2, was developed in the past three years at the Swiss Plasma Center in the scope of the EUROfusion conceptual studies for DEMO. The test results presented earlier proved an excellent DC performance, but large eddy currents loss in the segregated copper. Here we present the results of a prototype conductor assembled in late 2019 from an older section of RW2 cable and a novel stabilizer, made by two Rutherford cables of thick, high RRR copper wires extruded with a cladding of high resistivity CuNi alloy. The results of the test in SULTAN of the new prototype are discussed in terms of DC and AC loss performance. The AC loss is measured in both orientations, for sinusoidal and trapezoidal field pulses. The test is carried out at both 4.5 K and 20 K operating temperature, allowing separating the contribution of the eddy currents in the segregated copper from the other sources of ac loss, hysteresis and coupling loss. The goal of reducing the eddy currents to a level comparable to the coupling current loss is achieved with the cabled stabilizer, which is now retained as baseline for the React&Wind DEMO conductor.
13 January 2020 in IEEE Transactions on Applied Superconductivity
The Swiss Plasma Center (SPC) has developed a layout of Toroidal Field (TF) coil for EUROfusion DEMO tokamak, based on the reference tokamak baseline of 2015. Each TF coil winding pack is wound with graded Nb3Sn conductors and consists of 12 single layers, connected in series by means of inter-layer graded joints.
13 February 2019 in IEEE Transactions on Applied Superconductivity
High-field accelerator magnets of the next generation will require coil grading in order to decrease the amount of superconductor and hence the magnet cost. The joints between Nb 3 Sn conductor grades must have low electrical resistance (<1 nΩ) and reasonably good mechanical strength. The joints are classified as “Wind & React” because they will be assembled during the coil winding, prior to the heat treatment. Various techniques have been initially considered for the preparation of joints between Nb 3 Sn Rutherford cables, including soldering, diffusion bonding with and without interleaved copper foil, electroplated cables (to “smooth” the surface of the cable overlap), and crimped cables. Initial investigations included examinations of cross-sections (cut by electro-erosion). In a second stage, joint samples are prepared and assembled for test in the SULTAN test facility, with background field up to 11 T and operating current up to 14 kA. Besides the resistance test results, the selection of the most promising joint layout will also consider the restriction imposed by the coil manufacturing, e.g., available space for assembly, access after heat treatment, applicable quality control, etc.
12 February 2021 in IEEE Transactions on Applied Superconductivity
Future high-field accelerator magnets foresee the extensive use of Nb 3 Sn, more expensive than the Nb-Ti of LHC. For projects involving the series production of magnets, conductor grading is mandatory in order to reduce the cost. To allow grading, a splice between higher and lower grade cables must be implemented. The internal splice option, i.e., embedded in the winding pack, is the one considered in this manuscript. The magnet technology is Wind&React (W&R). The target resistance is 1 nΩ at a background field of B≈10 T and ratio between operational and critical current I/I c ≈1/3, the one at which such Nb 3 Sn dipoles are expected to work. This manuscript reports progress on ultrasonically welded, soldered and diffusion-bonded splices. The feasibility studies on ultrasonic welding between Nb 3 Sn Rutherford cables and strands is presented. The potential corrosive effect of fluxing agents of impregnated soldered samples is examined. In the end, the design and test in SULTAN of bent diffusion-bonded splices is reported.
This manuscript reports on the application of copper thermal spraying in the manufacturing process of an electrical connection between Nb3Sn cables for superconducting magnets of fusion reactors. The joint is realized through diffusion bonding of the sprayed coating of the two cables. The main requirement for such a connection is its electrical resistance, which must be below 1 nΩ at B = 8 T, I = 63.3 kA and T = 4.5 K. Micrographs of the joint prototype were taken to relate the joint resistance with its microstructure and to provide feedback on the manufacturing process. Optical microscopy (OM) was used to evaluate the grain size of the coating, presence of oxide phases and to analyze the jointed surfaces. Scanning electron microscopy (SEM) and, in particular, energy-dispersive X-ray spectroscopy (EDX) were used to confirm the elemental composition of specimens extracted from the prototype. It is shown that the copper coating has an oxide concentration of 40%. Despite this, the resistance of the prototype is 0.48 nΩ in operating conditions, as the oxides are in globular form. The contact ratio between the jointed surfaces is about 95%. In addition, residual resistivity ratio (RRR) measurements were carried out to quantify the electrical quality of the Cu coating.