Mehmet Acar

Dr. Mehmet Acar


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 August 2017 in BioResources
Verified
Journal Article
Closed access
HDHarun Diler
Harun Diler
MAMehmet Acar
Mehmet Acar
EBEngin Balıkçı
Engin Balıkçı
SDSelçuk Demirci
Selçuk Demirci
YEYusuf Z. Erdil
Yusuf Z. Erdil
The withdrawal force capacities were compared for T-type furniture joints made from heat-treated Siberian pine (Pinus sibirica), iroko (Chlorophora excelsa), and common ash (Fraxinus excelsior), which are commonly used in the construction of outdoor furniture. A total of 120 specimens that consisted of 3 wood species, 2 treatment processes (untreated and heat-treated), 2 adhesive types (polyurethane and polyvinyl acetate), and 2 joinery techniques (mortise and tenon, and dowel) were tested, with 5 replications for each condition. Half of the specimens were constructed from heat-treated wood materials, while the remaining half were prepared from untreated wood materials (control specimens). The joints constructed from common ash and iroko exhibited the highest withdrawal force capacity values. Overall, heat treatment reduced the withdrawal force capacity of joints by 25% compared with the joints constructed of control specimens. Mortise and tenon joints yielded 4 times higher performance than dowel joints. The polyurethane adhesive gave better results than the polyvinyl acetate adhesive. The best withdrawal force capacity values of heat-treated wood materials were obtained from the Iroko-polyurethane-mortise and tenon joint combination.

2 November 2017 in BioResources
Verified
Journal Article
Open access
PDF file
HKHalil Kılıç
Halil Kılıç
Ali KASALAli KASAL
Ali KASAL
TKTolga Kuşkun
Tolga Kuşkun
MAMehmet Acar
Mehmet Acar
YEYUSUF ZIYA ERDIL
YUSUF ZIYA ERDIL
Effect of Tenon Size on Static Front to Back Loading Performance of Wooden Chairs in Comparison with Acceptable Design Loads

25 March 2023 in Drvna industrija
Verified
Journal Article
Open access
PDF file
MAMehmet Acar
Mehmet Acar
EBEngin Balikci
Engin Balikci
TKTolga Kuskun
Tolga Kuskun
Ali KASALAli KASAL
Ali KASAL
YEYUSUF ZIYA ERDIL
YUSUF ZIYA ERDIL
The aim of this study was to investigate the effect of wood species, heat treatment, adhesive type and joint technique on shear force capacity of H-type furniture joints. For this purpose, an experimental design that consisted of 3 wood species, 2 treatment processes (untreated, heat-treated), 2 adhesive types (polyurethane (PUR), polyvinyl acetate (PVAc)) and 2 joint techniques (dowel, mortise-tenon (MT)) and 5 replications for each group were prepared, and accordingly, a total of 120 specimens were tested under static shear loads. Siberian pine (Pinus sibirica), Iroko (Chlorophora excelsa), and common ash (Fraxinus excelsior), which are commonly used in furniture constructions, were used as wood species. In general, iroko showed the highest shear force capacity between the wood species. The specimens constructed of heat-treated wood species showed lower shear force capacity by approximately 15 % in comparison to the same untreated specimens. MT joints showed better performance than dowel joints higher by approximately 21 %. PVAc adhesive gave higher values than PU adhesive by around 5 %. According to the results of four-way interactions, highest shear force capacities of H-type joints were obtained from “Common ash-PVAc-MT” combination in groups of untreated specimens and from “Iroko-PU-MT” combination in groups of heat-treated specimens.

16 December 2016 in Mugla Journal of Science and Technology
Verified
Journal Article
Open access
MYMehmet Yüksel
Mehmet Yüksel
HDHarun Diler
Harun Diler
MAMehmet Acar
Mehmet Acar
Yüzyıllardır eşsiz kündekari tekniğinin özellikleri bilinmektedir. geometrik bloklar ve kordonlu çitalar herhangi bir çivi veya tutkal kullanılmadan kiniş-zıvana yoluyla kilitli orijinal [gerçek] kündekari sistemi, tüm yapıyı çok dayanıklı hale getirir. Bu çalışmanın amacı, orijinal [gerçek] "Kündekari" tekniği ve taklit kündekari tekniklerinin özelliklerini incelemek, boyutsal ve fonksiyonel özelliklerini inceleyerek uygulanmış olan bazı kündekari elemanlarını analiz etmektir. Taklit "Kündekari" paneli yapmak gerçek kündekari panelden daha kolaydır. Taklit kündekari tekniğinin üç farklı yöntemi vardır. kabartma, yapıştırma-çakma ve kabartma-çakma. Gerçek ve taklit kündekari panellerinin deformasyon özellikleri araştırılmıştır ve örnekleri ile karşılaştırılmıştır. Sonuç olarak genellikle taklit kundekeri panellerindeki bazı kordonlu çıta ve geometric bloklarda düşmeler, çatlaklar, yarılmalar meydana gelmiştir. Yani nem ve sıcak havanın etkisiyle taklit kündekari mobilya ömrünün kısadır. Orijinal kündekari tekniği ile üretilen mobilyaların daha dayanıklı olduğunu kanıtlanmıştır.

1 February 2025 in BioResources
Verified
Journal Article
Closed access
MAMehmet Acar
Mehmet Acar
UAUğur Aras
Uğur Aras
SDSefa Durmaz
Sefa Durmaz
This study evaluated the outdoor performance of wood-plastic composites (WPCs) coated with epoxy-based coatings containing graphene nanoplatelets (GNPs) after 336 h of artificial weathering. Results indicated that color change is inevitable. The GNPs covered the surface of the WPCs and restrained the UV degradation. The lowest color changes were observed in the 0.5% GNPs coating. Contrastingly, crack formations were noted on the coating surface without GNPs. Scanning electron microscopy analysis clearly revealed the splitting of the coating due to UV exposure. As the GNPs ratios increased, the crack formation decreased. Similarly, the macroscopic investigation showed that the surface roughness of the coatings decreased with increasing GNPs. Color stabilization also improved with the increased GNPs. Meanwhile, color changes occurred more rapidly in WPCs coated with pure epoxy. Epoxy-based coatings containing GNPs effectively stabilized the surface color. Additionally, GNPs restricted mechanical losses, with a reduction of only 3.68% for the epoxy coating containing 1% GNPs, compared to a 19% loss in pure epoxy-coated WPCs. In conclusion, coatings containing GNPs considerably enhanced the weathering performance of WPCs.

29 September 2026 in Coloration Technology
Verified
Journal Article
Open access
SDSefa Durmaz
Sefa Durmaz
UAUgur Aras
Ugur Aras
IAİlKay Atar
İlKay Atar
MAMehmet Acar
Mehmet Acar
ÖKÖzlem Özgenç Keleş
Özlem Özgenç Keleş
EAErkan Avci
Erkan Avci
This study evaluates carbon black nanoparticle (CB NP)‐reinforced surface films for improving the durability, thermal stability, fire performance and mechanical retention of recycled high‐density polyethylene (HDPE)‐based wood‐plastic composites (WPCs) after 12 months of natural weathering. Characterisation was performed on film surfaces (colorimetry, fourier‐transform infrared spectroscopy [FTIR], field emission scanning electron microscopy [FE‐SEM]), isolated film layers (thermogravimetric analysis [TGA], differential scanning calorimetry [DSC]) and complete film–WPC systems (flexural properties, fire performance). CB NPs improved surface colour retention, which may be partly influenced by reduced spectrophotometric sensitivity of dark, broadband‐absorbing surface. Independently, stable FTIR peaks at 2915 and 2848 cm −1 , along with quantitatively stabilised carbonyl index (CI) values, demonstrated suppressed photo‐oxidative degradation at the polymer surface. Uncoated WPCs showed severe degradation, with a 47% reduction in modulus of rupture (MOR), along with surface cracking and interfacial debonding observed via FE‐SEM. Film coating slightly reduced MOR loss to 44%, whereas CB incorporation significantly limited it up to 19%. FE‐SEM confirmed reduced crack density, although some NP agglomeration was observed. TGA results indicated that CB increased T onset (~13%) and mitigated weathering‐induced reductions. DSC showed slight melting temperature increases and reduced crystallinity, while weathering promoted partial recrystallisation. Fire performance improved (~12.5%) with higher char formation. Overall, CB‐reinforced films enhance WPC durability for outdoor applications.