Aulia Chintia Ambarita

Ms. Aulia Chintia Ambarita


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 December 2021 in Polymers
Verified
Journal Article
Open access
PDF file
AAAulia Chintia Ambarita
Aulia Chintia Ambarita
Sri MulyatiSri Mulyati
Sri Mulyati
Nasrul ArahmanNasrul Arahman
Nasrul Arahman
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
NSNorazanita Shamsuddin
Norazanita Shamsuddin
NINoor Maizura Ismail
Noor Maizura Ismail
Polyethersulfone (PES) is the most commonly used polymer for membrane ultrafiltration because of its superior properties. However, it is hydrophobic, as such susceptible to fouling and low permeation rate. This study proposes a novel bio-based additive of dragonbloodin resin (DBR) for improving the properties and performance of PES-based membranes. Four flat sheet membranes were prepared by varying the concentration of DBR (0–3%) in the dope solutions using the phase inversion method. After fabrication, the membranes were thoroughly characterized and were tested for filtration of humic acid solution to investigate the effect of DBR loading. Results showed that the hydrophilicity, porosity, and water uptake increased along with the DBR loadings. The presence of DBR in the dope solution fastened the phase inversion, leading to a more porous microstructure, resulted in membranes with higher number and larger pore sizes. Those properties led to more superior hydraulic performances. The PES membranes loaded with DBR reached a clean water flux of 246.79 L/(m2·h), 25-folds higher than the pristine PES membrane at a loading of 3%. The flux of humic acid solution reached 154.5 ± 6.6 L/(m2·h), 30-folds higher than the pristine PES membrane with a slight decrease in rejection (71% vs. 60%). Moreover, DBR loaded membranes (2% and 3%) showed an almost complete flux recovery ratio over five cleaning cycles, demonstrating their excellent antifouling property. The hydraulic performance could possibly be enhanced by leaching the entrapped DBR to create more voids and pores for water permeation.

21 October 2021 in Polymers
Verified
Journal Article
Open access
PDF file
Nasrul ArahmanNasrul Arahman
Nasrul Arahman
CRCut Meurah Rosnelly
Cut Meurah Rosnelly
YYYusni Yusni
Yusni Yusni
AFAfrillia Fahrina
Afrillia Fahrina
SSSilmina Silmina
Silmina Silmina
Muhammad AzizMuhammad Aziz
Muhammad Aziz
α-Lactalbumin is an essential protein with multiple roles in physiological and the nutritional functionalities, such as diabetic prevention, blood pressure stabilization, and cancer cell inhibition. In the present work, polyethersulfone (PES)-based membranes were developed by incorporating Pluronic F127 and carbon nanotubes with single- and multi-walled dimensions (Sw-Cnts and Mw-Cnts) as additives. The resulting membranes were evaluated for use in the filtration of α-lactalbumin protein solution. Four series of membranes, including PES pristine membrane, were fabricated via the phase inversion process. The characteristics of the membrane samples were analyzed in terms of morphology, membrane surface hydrophilicity and roughness, and surface chemistry. The characterization results show that the incorporation of additive increased the surface wettability by reducing the surface water contact angle from 80.4° to 64.1° by adding F127 and Mw-Cnt additives. The highest pure water permeability of 135 L/(m2·h·bar) was also exhibited by the PES/F127/Mw-Cnt membrane. The performance of the modified membranes was clearly better than the pristine PSF for α-lactalbumin solution filtration. The permeability of α-lactalbumin solution increased from 9.0 L/(m2·h·bar) for the pristine PES membrane to 10.5, 11.0 and 11.5 L/(m2·h·bar) for membranes loaded with Pluronic F127, Sw-Cnts, and Mw-Cnts, respectively. Those increments corresponded to 17, 22, and 28%. Such increments could be achieved without altering the α-lactalbumin rejections of 80%. Remarkably, the rejection for the membrane loaded with Sw-Cnts even increased to 89%.

13 February 2024 in Korean Journal of Chemical Engineering
Verified
Journal Article
Closed access
PDF file
AAAulia Chintia Ambarita
Aulia Chintia Ambarita
Sri MulyatiSri Mulyati
Sri Mulyati
Nasrul ArahmanNasrul Arahman
Nasrul Arahman
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
BGBahar Yavuztürk Gül
Bahar Yavuztürk Gül
İKİsmail Koyuncu
İsmail Koyuncu

1 January 2023 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
Nasrul ArahmanNasrul Arahman
Nasrul Arahman
SISilmina
Silmina
AAAulia Chintia Ambarita
Aulia Chintia Ambarita
AFAfrilia Fahrina
Afrilia Fahrina
YUYusni
Yusni
MBMaughal Ahmed Ali Baig
Maughal Ahmed Ali Baig
Inorganic pore-forming agent modification on the polyethersulfone (PES) polymer membrane may have a critical approach to membrane technology to reduce membrane hydrophobicity and improve filtration performance. However, the visualization and characterization of the inorganic pore-forming agent distribution and copolymer impact on membrane surface properties is a lack. In this study, polymer-based membrane polyethersulfone (PES) combined with pluronic (Plu) and nanocarbon (NC) were analyzed systematically. Hydrophobic and chemical distribution were mainly investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM) that successfully resolved the pore size distribution and surface roughness parameters of pristine PES and modified PES/Plu/NC. The results showed that modified PES/Plu/NC had higher pore size distribution and surface roughness parameters than pristine PES and indicated that the PES membrane became more hydrophilic with Plu and NC addition. In the filtration performance, α-Lactalbumin has a higher permeability value using PES/Plu/NC than pristine PES membranes. Overall, the visualization and characterization approaches are essential for the filtration performance of polymer-based membrane modification.