Noor Maizura Ismail

Dr. Noor Maizura Ismail

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 April 2021 in Water
Verified
Journal Article
Open access
PDF file
Anwar Ameen Hezam SaeedAnwar Ameen Hezam Saeed
Anwar Ameen Hezam Saeed
Noorfidza Yub HarunNoorfidza Yub Harun
Noorfidza Yub Harun
SSSuriati Sufian
Suriati Sufian
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
BNBaiq Asma Nufida
Baiq Asma Nufida
BABaker Al-dhawi
Baker Al-dhawi
Cadmium is one of the most hazardous metals in the environment, even when present at very low concentrations. This study reports the systematic development of Kenaf fiber biochar as an adsorbent for the removal of cadmium (Cd) (II) ions from water. The adsorbent development was aided by an optimization tool. Activated biochar was prepared using the physicochemical activation method, consisting of pre-impregnation with NaOH and nitrogen (N2) pyrolysis. The influence of the preparation parameters—namely, chemical impregnation (NaOH: KF), pyrolysis temperature, and pyrolysis time on biochar yield, removal rate, and the adsorption capacity of Cd (II) ions—was investigated. From the experimental data, some quadratic correlation models were developed according to the central composite design. All models demonstrated a good fit with the experimental data. The experimental results revealed that the pyrolysis temperature and heating time were the main factors that affected the yield of biochar and had a positive effect on the Cd (II) ions’ removal rate and adsorption capacity. The impregnation ratio also showed a positive effect on the specific surface area of the biochar, removal rate, and adsorption capacity of cadmium, with a negligible effect on the biochar yield. The optimal biochar-based adsorbent was obtained under the following conditions: 550 °C of pyrolysis temperature, 180 min of heating time, and a 1:1 NaOH impregnation ratio. The optimum adsorbent showed 28.60% biochar yield, 69.82% Cd (II) ions removal, 23.48 mg/g of adsorption capacity, and 160.44 m2/g of biochar-specific area.

4 June 2021 in Polymers
Verified
Journal Article
Open access
PDF file
ADAris Doyan
Aris Doyan
SSSusilawati Susilawati
Susilawati Susilawati
Saiful PrayogiSaiful Prayogi
Saiful Prayogi
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
MAMuhamad Fatikul Arif
Muhamad Fatikul Arif
NINoor Maizura Ismail
Noor Maizura Ismail
This study investigated the polymer film composite of polyvinyl alcohol (PVA), trichlorethylene (TCE) and cresol red (CR) dye irradiated with gamma (γ) rays for potential application as radiation dosimetry. The film was prepared via the solvent-casting method with varying concentrations of TCE. Film samples were exposed to radiation from a γ-rays radiation source of 60Cobalt isotope. Color changes before and after γ-rays irradiation were observed, and the optical properties of the polymer films were investigated by spectrophotometry. Results show that increasing the radiation dose physically changed the color of the polymer film, from purple (pH > 8.8) without radiation (0 kGy) to yellow (almost transparent) (2.8 < pH < 7.2) at the highest dose (12 kGy). The concentration of acid formed due to irradiation increased with the increase in irradiation doses and at higher TCE content. The critical doses of PVA-TCE composites decreased linearly with the increase of TCE composition, facilitating an easy calibration process. The dose response at 438 nm increased exponentially with increasing radiation dose, but showed an opposite trend at the 575 nm band. An increase in the TCA concentration indicated a decrease in the absorption edge and an increase in activation energy, but both decreased for all TCE concentrations at higher doses. The energy gap for the direct and the indirect transitions decreased with increasing TCE concentration and γ-rays radiation dose. The results of this study demonstrated the potential application of PVA-TCE-CR polymer film as γ-rays irradiation dosimetry in a useful dose range of 0–12 kGy.

19 May 2022 in Polymers
Verified
Journal Article
Open access
PDF file
THTok Sheng Hung
Tok Sheng Hung
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
NSNorazanita Shamsuddin
Norazanita Shamsuddin
HSHazwani Suhaimi
Hazwani Suhaimi
NINoor Maizura Ismail
Noor Maizura Ismail
Ahmad Fauzi IsmailAhmad Fauzi Ismail
Ahmad Fauzi Ismail
Ultra-low-pressure membrane (ULPM) filtration has emerged as a promising decentralized water and wastewater treatment method. It has been proven effective in long-term filtration under stable flux without requiring physical or chemical cleaning, despite operating at considerably lower flux. The use of ultra-low pressure, often simply by hydrostatic force (often called gravity-driven membrane (GDM) filtration), makes it fall into the uncharted territory of common pressure-driven membrane filtration. The applied polymeric membrane is sensitive to compaction, wetting, and fouling. This paper reviews recent studies on membrane compaction, wetting, and fouling. The scope of this review includes studies on those phenomena in the ULPM and how they affect the overall performance of the system. The performance of GDM systems for water and wastewater treatment is also evaluated. Finally, perspectives on the future research direction of ULPM filtration are also detailed.

10 November 2020 in Polymers
Verified
Journal Article
Open access
PDF file
Muthia ElmaMuthia Elma
Muthia Elma
DMDwi Rasy Mujiyanti
Dwi Rasy Mujiyanti
NINoor Maizura Ismail
Noor Maizura Ismail
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
ARAulia Rahma
Aulia Rahma
ERErdina Lulu Atika Rampun
Erdina Lulu Atika Rampun
Water scarcity is still a pressing issue in many regions. The application of membrane technology through water desalination to convert brackish to potable water is a promising technology to solve this issue. This study compared the performance of templated TEOS-P123 and ES40-P123 hybrid membranes for brackish water desalination. The membranes were prepared by the sol–gel method by employing tetraethyl orthosilicate (TEOS) for the carbon-templated silica (soft template) and ethyl silicate (ES40) for the hybrid organo-silica. Both sols were templated by adding 35 wt.% of pluronic triblock copolymer (P123) as the carbon source. The silica-templated sols were dip-coated onto alumina support (four layers) and were calcined by using the RTP (rapid thermal processing) method. The prepared membranes were tested using pervaporation set up at room temperature (~25 °C) using brackish water (0.3 and 1 wt.%) as the feed. It was found that the hybrid membrane exhibited the highest specific surface area (6.72 m2·g−1), pore size (3.67 nm), and pore volume (0.45 cm3·g−1). The hybrid ES40-P123 was twice thicker (2 μm) than TEOS-P123-templated membranes (1 μm). Lastly, the hybrid ES40-P123 displayed highest water flux of 6.2 kg·m−2·h−1. Both membranes showed excellent robustness and salt rejections of >99%.

17 December 2021 in Polymers
Verified
Journal Article
Open access
PDF file
AAAulia Chintia Ambarita
Aulia Chintia Ambarita
Sri MulyatiSri Mulyati
Sri Mulyati
Nasrul ArahmanNasrul Arahman
Nasrul Arahman
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
NSNorazanita Shamsuddin
Norazanita Shamsuddin
NINoor Maizura Ismail
Noor Maizura Ismail
Polyethersulfone (PES) is the most commonly used polymer for membrane ultrafiltration because of its superior properties. However, it is hydrophobic, as such susceptible to fouling and low permeation rate. This study proposes a novel bio-based additive of dragonbloodin resin (DBR) for improving the properties and performance of PES-based membranes. Four flat sheet membranes were prepared by varying the concentration of DBR (0–3%) in the dope solutions using the phase inversion method. After fabrication, the membranes were thoroughly characterized and were tested for filtration of humic acid solution to investigate the effect of DBR loading. Results showed that the hydrophilicity, porosity, and water uptake increased along with the DBR loadings. The presence of DBR in the dope solution fastened the phase inversion, leading to a more porous microstructure, resulted in membranes with higher number and larger pore sizes. Those properties led to more superior hydraulic performances. The PES membranes loaded with DBR reached a clean water flux of 246.79 L/(m2·h), 25-folds higher than the pristine PES membrane at a loading of 3%. The flux of humic acid solution reached 154.5 ± 6.6 L/(m2·h), 30-folds higher than the pristine PES membrane with a slight decrease in rejection (71% vs. 60%). Moreover, DBR loaded membranes (2% and 3%) showed an almost complete flux recovery ratio over five cleaning cycles, demonstrating their excellent antifouling property. The hydraulic performance could possibly be enhanced by leaching the entrapped DBR to create more voids and pores for water permeation.

3 January 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Sri MulyatiSri Mulyati
Sri Mulyati
SASri Aprilia
Sri Aprilia
Syawaliah MuchtarSyawaliah Muchtar
Syawaliah Muchtar
YSYanna Syamsuddin
Yanna Syamsuddin
CRCut Meurah Rosnelly
Cut Meurah Rosnelly
NINoor Maizura Ismail
Noor Maizura Ismail
Potential use of tannic acid (TA) as an additive for fabrication of polyvinylidene difluoride (PVDF) membrane was investigated. The TA was introduced by blending into the dope solution with varying concentrations of 0, 1, 1.5, and 2 wt%. The prepared membranes were characterized and evaluated for filtration of humic acid (HA) solution. The stability of the membrane under harsh treatment was also evaluated by one-week exposure to acid and alkaline conditions. The results show that TA loadings enhanced the resulting membrane properties. It increased the bulk porosity, water uptake, and hydrophilicity, which translated into improved clean water flux from 15.4 L/m2.h for the pristine PVDF membrane up to 3.3× for the TA-modified membranes with the 2 wt% TA loading. The flux recovery ratio (FRR) of the TA-modified membranes (FRRs = 78–83%) was higher than the pristine one (FRR = 58.54%), with suitable chemical stability too. The improved antifouling property for the TA-modified membranes was attributed to their enhanced hydrophilicity thanks to improved morphology and residual TA in the membrane matric.