Michał Kawiak

Dr. Michał Kawiak

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 December 2021 in Materials
Verified
Journal Article
Open access
PDF file
PZPrzemysław Zmitrowicz
Przemysław Zmitrowicz
MKMichał Kawiak
Michał Kawiak
PKPaweł Kochmański
Paweł Kochmański
JBJolanta Baranowska
Jolanta Baranowska
K-TIG (Keyhole Tungsten Inert Gas) method is a new, emerging welding technology that offers a significant acceleration of the joining process, even for very thick plates. However, its potential for welding of certain materials is still unknown. Particularly challenging are duplex steels as this technology does not allow the use of a filler material, which is crucial for these steels and for weld joint microstructure adjustment. In order to demonstrate the suitability of this technology for single-pass welding of 1.4462 duplex steel detailed studies of the microstructure of the weld joints obtained for different linear energies were carried out and discussed with respect to their mechanical properties. According to the results obtained, the heat-affected zone (HAZ) shows a microstructure similar to the HAZ of duplex steel welded with the traditional TIG multi-pass methods. However, the weld, due to the lack of filler material, had a microstructure different to that typical for duplex steel welded joints and was also characterized by an increased content of ferrite. However, all joints, both in terms of microstructure and mechanical properties, met the requirements of the relevant standards. Moreover, the K-TIG process can be carried out in the linear energy range typical of duplex steel welding, although further optimization is needed.

13 March 2024 in Engineering Failure Analysis
Verified
Journal Article
Closed access
MKMichał Kawiak
Michał Kawiak
PKPaweł Kochmański
Paweł Kochmański

1 August 2024 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
MKMichał Kawiak
Michał Kawiak
SKSławomir Janusz Krajewski
Sławomir Janusz Krajewski
Kamil UrbanowiczKamil Urbanowicz
Kamil Urbanowicz
The loss of steerage in maritime vessels often stems from main engine failures, as expounded in the present article. The focal incident involves a cascading engine breakdown initiated by a single exhaust valve fault. Subsequent consequences encompass the fragmentation of the second exhaust valve,...

22 December 2025 in Materials
Verified
Journal Article
Open access
PDF file
MKMichał Kawiak
Michał Kawiak
Alexander BalitskiiAlexander Balitskii
Alexander Balitskii
MKMarcin A. Królikowski
Marcin A. Królikowski
VBValentina Balitska
Valentina Balitska
JDJakub Dowejko
Jakub Dowejko
Comprehensive investigations of the serviceability of pearlite (R260) steel have been performed and, especially, of the serviceability of their welded joints (WJ) during long-term operation in hydrogen-containing environments for application in additive manufacturing technology. It is important to estimate the durability of these steels and their WJ in hydrogen and develop the procedures of analysis of the influence of hydrogen during long-term operation. It has been experimentally observed that hydrogen absorbed (0.4 … 0.8 ppm) by the pearlite (R260) steel while welding, and subsequent operation thereof, exercises considerable influence on fatigue and brittle fractures of the constructions from which they are manufactured. Accordingly, in hydrogen-saturated (up to 4.7 ppm) specimens, the desired fatigue crack can be obtained at a considerably lower number of cycles of the same dynamic load than in non-hydrogenated ones. Increased hydrogen content can also affect crack propagation. Tests have shown that critical fracture occurs faster in hydrogenated specimens (46.6 MPa m0.5) than in non-hydrogenated ones. Also, hydrogenated specimens exhibit lower fracture toughness than their non-hydrogenated counterparts. Finally, it has been demonstrated that the fracture toughness of specimens taken from rail negligibly (49.7 … 50.7 MPa m0.5) depend on their orientation (L–S or S–L).