In a previous work, an ink based on a preceramic polymer, SiC fillers, and chopped carbon fibers was proposed for the production of Ceramic Matrix Composite (CMC) structures by Direct Ink Writing (DIW) and subsequent pyrolysis. Thanks to the shear stresses generated at the nozzle tip during extrusion, carbon fibers can be aligned along the printing direction. Fumed silica was added to the ink in order to enhance its rheological properties; however, the printed structures still showed some deformation in the Z direction. In this work, a second ink was successfully developed to limit deformation and at the same time avoid the addition of fumed silica, which limited the potential temperature of application of the composites. Instead, the positive role of the preceramic polymer on the ink rheology was exploited by increasing its concentration in the ink. Rheological characterization carried out on both inks confirmed that they possessed Bingham shear thinning behavior and fast viscosity recovery. Single filaments with different diameters (~310 µm and ~460 µm) were produced with the latter ink by DIW and subsequent pyrolysis. Tested under a four-point flexural test, the filaments showed a mean flexural strength above 30 MPa, graceful failure, and fiber pull-out. The results of this work suggest that CMC components can effectively be fabricated via DIW of a preceramic ink with embedded short fibers; the preceramic polymer is able to provide the desired rheology for the process and to develop a dense matrix capable of incorporating both fibers and ceramic particles, whereas the fibers addition contributes to an increase of the fracture toughness of the material and to the development of a graceful failure mode.

The small‐signal dielectric and piezoelectric coefficients of paper‐derived sodium potassium niobate, K _0.5 Na _0.5 NbO ₃ (KNN), were compared with those of conventionally prepared samples. Results show similar functional properties of paper‐derived KNN without significantly decreasing the small‐signal piezoelectric coefficient. The structure and microstructure analysis of conventional KNN and paper‐derived KNN did not reveal any significant difference in the crystal structure and grain size. However, the temperature‐dependent inter‐ferroelectric phase transition temperature estimated from the temperature‐dependent dielectric permittivity data revealed a decrease of approximately 18°C for the paper‐derived KNN and is possibly associated with the structural and microstructural defects. This work indicates that optimizing suspension chemistry and sintering conditions will be critical to enhance the functional response of paper‐derived KNN further. Moreover, paper‐derived ceramic processing, a novel and cost‐effective additive manufacturing technology, can be potentially used to fabricate other electroceramics with a wide range of porosities and sizes as well as complex geometries and multilayer structures.

In this work, the binder jetting 3D printing of boron carbide was combined with a subsequent liquid silicon infiltration procedure to produce reaction-bonded boron carbide (RBBC)-based structures. After printing, the samples were isostatically pressed to obtain more homogeneous and denser microstructures while maintaining their complex shapes. The RBBC bodies were successfully fabricated, and the influence of the binder content on the amount of residual silicon was studied. By increasing the binder content from 10 to 22.5 vol.%, the Si content decreased from ~28 to ~12 vol.%. The mechanical properties dependent on the Si content were additionally investigated. The measured average values for the bending strength (~355 MPa), Young’s modulus (~348 GPa), and hardness (~20 GPa) are comparable to those reported in the literature for RBBC-based materials.

Coextrusion by robocasting is a suitable process for fabricating multimaterial ceramic structures. Herein, the robocasting process is used to fabricate core–shell structures, combined with subsequent liquid silicon infiltration (LSI). Thus, reaction‐bonded silicon carbide (RBSC), reaction‐bonded boron carbide (RBBC), and reaction‐bonded silicon–boron carbide composites are produced. The LSI process offers the possibility to circumvent high temperatures and pressures used in traditional fabrication. Pastes with high solid loading and necessary carbon content are used in order to combine the robocasting with the subsequent LSI process. The influence of the paste rheology on the sample fabrication of multimaterial core–shell structures of reaction‐bonded carbides is investigated. The key rheological data, such as the viscosities of the combined pastes, are correlated with the observations from the microstructural investigation using scanning electron microscopy. A correlation between the difference in viscosity and the core geometry can be established. Crack formation in the material combination of RBSC and RBBC is found and compared with layered multimaterial structures of reaction‐bonded carbides. Residual stresses, which can be used to explain the crack formation, are investigated using Raman spectroscopy.

This paper presents the results of microstructural analysis of novel preceramic paper-derived SiCf/SiC composites fabricated by spark plasma sintering. The sintering temperature and pressure were 2100/2200 °C and 60/100 MPa, respectively. The content of fibers in the composites was approx. 10 wt %. The SiC_f/SiC composites were analyzed by positron annihilation methods, X-ray diffraction technology, scanning electron microscopy, and Raman spectroscopy. Longer sintering time causes the proportion of the 6H-SiC composition to increase to ~80%. The increase in sintering temperature from 2100 °C to 2200 °C leads to partial transition of 4H-SiC to 6H-SiC during the sintering process, and the long-life component of positrons indicates the formation of Si vacancies. The Raman characteristic peaks of turbostratic graphite appear in the Raman spectrum of SiC fibers, this is caused by the diffusion of carbon from the surface of the SiC fiber and the preceramic paper during the high-temperature sintering process.

Ceramic materials are chemical- and temperature-resistant and, therefore, enable novel application fields ranging from automotive to aerospace. With this in mind, this contribution focuses on developing an additive manufacturing approach for 3D-printed waveguides made of ceramic materials. In particular, a special design approach for ceramic waveguides, which introduces non-radiating slots into the waveguides sidewalls, and a customized metallization process, are presented. The developed process allows for using conventional stereolithographic desktop-grade 3D-printers. The proposed approach has, therefore, benefits such as low-cost fabrication, moderate handling effort and independence of the concrete waveguide geometry. The performance of a manufactured ceramic WR12 waveguide is compared to a commercial waveguide and a conventionally printed counterpart. For that reason, relevant properties, such as surface roughness and waveguide geometry, are characterized. Parsing the electrical measurements, the ceramic waveguide specimen features an attenuation coefficient of 30–60 dB/m within the E-Band. The measured attenuation coefficient is 200% and 300% higher compared to the epoxy resin and the commercial waveguide and is attributed to the increased surface roughness of the ceramic substrate.