In continuous-wave (CW) radar systems, such as frequency-modulated (FMCW), frequency-stepped (FSCW), or orthogonal frequency-division multiplexing (OFDM) radar systems, the range and velocity uncertainty are significantly impaired by phase noise decorrelation. Therefore, radar designers require accurate knowledge of their synthesizers’ phase noise profiles to assess and predict radar performance. However, commercial phase noise analyzers cannot determine phase noise during modulation, and this may differ notably from phase noise in the pure CW mode. Recent methods for FMCW phase noise analysis usually require comprehensive ${a}$ priori knowledge of modulation parameter and are prone to systematic deviations. To overcome these issues, we propose a new approach based on differential analysis of subsequent time-domain measurements. This method retains, statistical phase noise information while reducing systematic influences. For the first time, less ${a}$ priori signal knowledge is required, and the method works for nearly any kind of broadband signal modulation. The concept requires only a digitizer (e.g., an oscilloscope) and some digital signal processing. The proposed method is first experimentally tested with different phase-locked-loop (PLL)-based synthesizer phase noise profiles. The obtained phase noise profiles agree perfectly with the results of an established measurement system. After this proof of basic functionality, the unique phase noise analysis capability for BB modulated signals is demonstrated with PLL-generated FMCW signals. The results reveal a significant phase noise difference between the different setups and clearly show the capability and benefit of the novel phase noise spectral density measurement concept.

Nowadays, additive manufacturing provides far-reaching possibilities for use in radio frequency components. In addition to almost unlimited freedom of design as compared to conventional manufacturing, the absence of further assembly steps is a key aspect of 3D printing. In this paper, a 3D printed monolithic antenna for millimeter wave-sensing applications is presented with a full hemispherical coverage. The antenna is designed as an ensemble of a waveguide horn antenna and a differentially fed dipole antenna. The slotted waveguide approach was utilized to improve the manufacturing quality on the waveguide inside. The influence of two optimized antenna elements, a metal plane, and a cut-out window, on the beam pattern is comprehensively investigated. A huge half power beam width of 142∘ in both directions, elevation and azimuth, is presented at 79 GHz and a boresight gain of 4.7 dBi was measured. The beam pattern in the frequency range from 76 to 81 GHz is studied in greater detail, where a half power beam width of at least 112∘ is achieved. Due to the -10 dB matching capability bandwidth of over 28 GHz, the antenna is also suitable for extremely broadband applications with a –5 dB angular width of better than 100∘. Furthermore, the system design describes how to integrate the antenna into hybrid circuit designs and the manufacturing tolerances are examined. The antenna offers attractive possibilities for millimeter wave-sensing applications in the area of assisted living and industrial monitoring, especially whenever blind spots have to be avoided.

Ceramic materials are chemical- and temperature-resistant and, therefore, enable novel application fields ranging from automotive to aerospace. With this in mind, this contribution focuses on developing an additive manufacturing approach for 3D-printed waveguides made of ceramic materials. In particular, a special design approach for ceramic waveguides, which introduces non-radiating slots into the waveguides sidewalls, and a customized metallization process, are presented. The developed process allows for using conventional stereolithographic desktop-grade 3D-printers. The proposed approach has, therefore, benefits such as low-cost fabrication, moderate handling effort and independence of the concrete waveguide geometry. The performance of a manufactured ceramic WR12 waveguide is compared to a commercial waveguide and a conventionally printed counterpart. For that reason, relevant properties, such as surface roughness and waveguide geometry, are characterized. Parsing the electrical measurements, the ceramic waveguide specimen features an attenuation coefficient of 30–60 dB/m within the E-Band. The measured attenuation coefficient is 200% and 300% higher compared to the epoxy resin and the commercial waveguide and is attributed to the increased surface roughness of the ceramic substrate.

This paper presents a W-band (75-110 GHz) frequency-scanning leaky-wave antenna with backward-to-forward rapid beam-scanning capability. The design takes advantage of the low-loss and high-dispersion features of an air-filled composite right/left-handed metallic waveguide. Equivalent circuit modeling and a detailed design procedure are presented to facilitate the analysis and design. The design method is validated by a prototype antenna using 3D printing technology. Measurement results are consistent with simulated ones and show a wide field-of-view (FoV) from -15° to +35° when the radiated frequency is swept from 75.4GHz to 79.4GHz, equivalent to a high scanning rate of 9.68°/%BW. In simulation, when operated from 76.5GHz to 81.5GHz, the FoV can cover from -30° to +50°, which translates to a scanning rate of 12.64°/%BW. To the best of the authors’ knowledge, the presented antenna achieves the highest scanning rate in the W-band. The presented design may be a good candidate for millimeter-wave imaging applications that require low loss and rapid beam-scanning, including automotive radars.