Ruifeng Dong

Prof. Ruifeng Dong

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2023 in Materials Research Express
Verified
Journal Article
Open access
ZXZhang Xiaoyu
Zhang Xiaoyu
RDRuifeng Dong
Ruifeng Dong
GBGao Bo
Gao Bo
CJChen Jiquan
Chen Jiquan
MZMu Zhipeng
Mu Zhipeng
YXYang Xiong
Yang Xiong
In this study, a high-strength, offshore platform steel, EH420, was used as the original steel. By observing the original austenite morphology, the corrosion resistance of three experimental steels with different rare Earth contents in a simulated marine splash zone was compared and studied using cyclic immersion corrosion and electrochemical corrosion tests. The macro- and micromorphologies of three experimental steels in different cycles of corrosion, as well as the composition of rust layers, were observed and studied by employing an optical microscope, scanning electron microscope (SEM) and X-ray diffraction (XRD). The crystal microstructure of the three experimental of steels was analyzed by EBSD, and the electrochemical behavior of the three experimental of steels after corrosion was analyzed by electrochemical polarization curve and electrochemical impedance spectroscopy. The results show that the trace additions of Ce ( less than 20ppm ) in the steel can refine the grain size, reduce the grain boundary energy, promote the formation of the protective phase α-FeOOH and Fe3O4 of the rust layer, improve the compactness of the rust layer, and reduce the corrosion rate. In addition, the charge transfer resistance ( Rct ) and open circuit potential are increased, and the corrosion current density is reduced. Moreover, the higher the content of Ce is added in the steel, the more obvious its effect.Therefore, the trace additions of Ce improves the corrosion resistance of high strength offshore platform steel.

30 September 2024 in Crystals
Verified
Journal Article
Open access
PDF file
RDRuifeng Dong
Ruifeng Dong
PZPeiying Zhou
Peiying Zhou
JCJiquan Chen
Jiquan Chen
YLYuansu Lei
Yuansu Lei
XYXiong Yang
Xiong Yang
QCQingling Cui
Qingling Cui
In this paper, FH460 special steel with rare earth element cerium (Ce) was selected, and the control group without Ce was set up. By changing the content of Ce, the microstructure, phase transition point, and mechanical properties of the test steel were observed to study the effect of trace rare earth element Ce on the microstructure and mechanical properties of high-strength marine engineering steel. The morphology and energy spectrum of inclusions in three kinds of test steels were observed by SEM, and the morphological changes in inclusions in FH460 high-strength marine engineering steel after adding Ce were investigated. The fracture morphology and energy spectrum analysis were carried out by combining the tensile test at room temperature and the gradient low temperature impact toughness test, and the effect of trace Ce on the mechanical properties of the test steel was comprehensively analyzed. The results show that the addition of Ce changes the phase transformation temperature of Ac1 and Ac3, and refines the original microstructure of the test steel. SEM observation showed that the addition of Ce changed the long strip MnS and polygonal irregular Al2O3 inclusions into ellipsoids, which reduced the size of inclusions. The gradient low temperature impact test shows that with the decrease in temperature, the fracture dimple depth of the three test sheets of steel decreases, and the Ce-containing test steel forms a deep dimple centered on rare earth inclusions, which hinders the crack propagation and significantly improves the low temperature impact toughness of the test steel.

6 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
QZQingbo Zhao
Qingbo Zhao
RDRuifeng Dong
Ruifeng Dong
YLYongfa Lu
Yongfa Lu
YYYang Yang
Yang Yang
YWYanru Wang
Yanru Wang
XYXiong Yang
Xiong Yang
Rare-earth elements have been widely used in the field of functional materials, but their effects on the cold-stamping formability of high-strength automotive steels have rarely been studied. In this paper, the effect of the trace rare-earth element Ce on the microstructure and properties of cold-rolled medium manganese steel after ART (austenite-reverted transformation, ART) annealing was studied. The microstructure of the experimental steel was observed using SEM, and the mechanical properties were tested using a universal tensile testing machine. The volume fraction of the retained austenite and the texture of the steel were measured using XRD. The results showed that the original austenite grain size of the experimental steel was smaller after adding the trace rare-earth element Ce. After ART annealing, the grain size distribution of the experimental steel with rare-earth Ce was more uniform, and the comprehensive mechanical properties were better. Under the conditions of quenching at 800 °C for 5 min and annealing at 645 °C for 15 min, the maximum product of tensile strength and elongation was 28.47 GPa·%.

15 March 2024 in Metals
Verified
Journal Article
Open access
PDF file
RDRuifeng Dong
Ruifeng Dong
JLJian Li
Jian Li
ZCZishuai Chen
Zishuai Chen
WZWei Zhang
Wei Zhang
XZXing Zhou
Xing Zhou
The primary objective of this paper is to investigate the influence of deformation degree on the microstructure and properties of a Ni-based superalloy. An upsetting experiment was conducted using a free-forging hammer to achieve a deformation degree ranging from 60% to 80%. The impact of the forging deformation degree on the hardness and high-temperature erosion performance was evaluated using the Rockwell hardness tester (HRC) and high-temperature erosion tester, respectively. The experimental results indicate that as the deformation degree increased, the hardness of the forged material progressively increased while the rate of high-temperature erosion gradually decreased. In order to comprehensively study the mechanism behind the variations in forging performance, optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM) were employed. The findings reveal that as the deformation degree increased, the presence of small-angle grain boundaries and an increase in grain boundary area contributed to enhanced hardness in the alloy forgings. Furthermore, it was discovered that grain boundaries with twin orientation promoted dynamic recrystallization during deformation, specifically through a discontinuous dynamic recrystallization mechanism. Additionally, the precipitated γ′ phase in the alloy exhibited particle sizes ranging from 40 to 100 nm. This particle size range resulted in a higher critical shear stress value and a more pronounced strengthening effect on the alloy.

17 January 2025 in Metals
Verified
Journal Article
Open access
PDF file
JCJiquan Chen
Jiquan Chen
RDRuifeng Dong
Ruifeng Dong
YLYuansu Lei
Yuansu Lei
PZPeiying Zhou
Peiying Zhou
XYXiong Yang
Xiong Yang
LFLifeng Fan
Lifeng Fan
In this study, Q370qENH high-strength weathering bridge steel was used as the base material. The corrosion experiment in a marine atmosphere was simulated by the salt spray test, and the outdoor atmospheric exposure corrosion experiment and electrochemical method test were carried out. The corrosion behavior of Q370qENH high-strength weathering bridge steel in a marine atmosphere was studied using electron probe microanalysis (EPMA), field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), and other surface testing techniques. The results show that the corrosion rate of the steel gradually decreases with the increase in the content of trace rare earth elements. Ce played a role in the modification of inclusions so that MnS was modified into rare earth composite inclusions, which slowed down the occurrence of corrosion. The enrichment of Cu alloy elements in the inner rust layer of the rare earth experimental steel improves the compactness of the rust layer, and the thickness of the inner rust layer is increased by 42%, which enhances the stability of the rust layer. With the increase in cerium, the protection coefficient α/γ* of the rust layer of experimental steel increases, indicating that the corrosion resistance of the material is improved. In addition, the electrochemical results show that the addition of rare earth elements in Q370qENH steel will lead to a positive shift in the electrochemical self-corrosion potential, a larger impedance radius of the steel rust layer, and a stronger protective effect. Due to the addition of trace cerium, the seawater corrosion resistance of the test steel is improved.

23 May 2025 in Materials
Verified
Journal Article
Open access
PDF file
彦吴彦杰 吴
彦杰 吴
RDRuifeng Dong
Ruifeng Dong
ZMZhipeng Mu
Zhipeng Mu
JGJing Guo
Jing Guo
XYXiong Yang
Xiong Yang
PZPeiying Zhou
Peiying Zhou
This study investigated the corrosion behavior and mechanism of offshore platform steel in a simulated marine atmospheric environment using electrochemical analysis, phase analysis, and rust layer characterization. The findings demonstrate that the addition of trace amounts of the rare earth element Ce significantly enhances the steel’s corrosion resistance in the marine environment and effectively reduces the corrosion rate. The addition of Ce promotes the enrichment of Cr in the inner rust layer and forms a dense protective rust layer, thereby preventing the rust layer from falling off, as well as hindering the penetration of oxygen ions. Phase analysis and electrochemical studies further confirmed that the addition of rare earth Ce optimized the structure of the rust layer, improved the matrix protection effect, and enhanced the corrosion resistance of the steel. The crystal structure of the rust layer and the stability between the matrix were simulated by first principles. The results show that the addition of rare earth enhances the bonding force and compactness of the steel matrix and the rust layer, thereby improving corrosion resistance.