In order to develop a third-generation automobile steel with powerful strength and elongation, we propose a method through high temperature quenching and two-phase region reverse-phase transformation annealing to develop such steel with 0.13% C and 5.4% Mn. To investigate the microstructure evolution and mechanical properties of manganese steel, SEM, XRD and TEM are employed in our experiments. Experimental results indicate that the microstructure after quenching is mainly lath martensite microstructure with average of lath width at 0.5 μm. The components of the steel after along with reverse-phase transformation annealing are ultra-fine grain ferrite, lath martensite and different forms of austenite microstructure. When the temperature at 625 °C, the components of the steel mainly includes lath martensite microstructure and ultra-fine grain ferrite and the fraction of austenite volume is only 5.09%. When the annealing temperature of reverse-phase transformation increase into 650 °C and 675 °C, the austenite appears in the boundary of the ferritic grain boundary and the boundary of lath martensite as the forms of bulk and lath. The phenomenon appears in the bulk of austenite, and the size of is 0.22 μm, 0.3 μm. The fraction of austenite volume is 22.34% at 675 °C and decreases into 9.32% at 700 °C. The components of austenite mainly includes ultra-fine grained ferrite and lath martensite. Furthermore, the density of decreases significantly, and the width of martensite increases into 0.32 μm. In such experimental settings, quenching at 930 °C with 20 min and at 675 °C with 30 min reverse-phase transformation annealing, the austenite volume fraction raises up to 22.34%.
In this study, Q370qENH high-strength weathering bridge steel was used as the base material. The corrosion experiment in a marine atmosphere was simulated by the salt spray test, and the outdoor atmospheric exposure corrosion experiment and electrochemical method test were carried out. The corrosion behavior of Q370qENH high-strength weathering bridge steel in a marine atmosphere was studied using electron probe microanalysis (EPMA), field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), and other surface testing techniques. The results show that the corrosion rate of the steel gradually decreases with the increase in the content of trace rare earth elements. Ce played a role in the modification of inclusions so that MnS was modified into rare earth composite inclusions, which slowed down the occurrence of corrosion. The enrichment of Cu alloy elements in the inner rust layer of the rare earth experimental steel improves the compactness of the rust layer, and the thickness of the inner rust layer is increased by 42%, which enhances the stability of the rust layer. With the increase in cerium, the protection coefficient α/γ* of the rust layer of experimental steel increases, indicating that the corrosion resistance of the material is improved. In addition, the electrochemical results show that the addition of rare earth elements in Q370qENH steel will lead to a positive shift in the electrochemical self-corrosion potential, a larger impedance radius of the steel rust layer, and a stronger protective effect. Due to the addition of trace cerium, the seawater corrosion resistance of the test steel is improved.
Influence of temperature scheme on the microstructure and properties variation of medium carbon steel warm deformation was studied with testing equipment of Gleeble-3500, SEM, TEM, EBSD, and φ350 reversal rolling mill. The results show that the temperature of 650 facilitates the formation of ultrafine homogeneous microstructure. The microstructure formed during temperature range of 650–700 °C is relative homogeneous and fine. The mechanical properties of warm rolling are influenced by the cooling modes. The lower cooling rate is benefit to the combination of strength and ductility.
The Cu-Cr-Zr alloy is regarded as an optimal material for high-end electronic information industries owing to its high electrical strength, high conductivity, and outstanding softening resistance. Nevertheless, the impacts of Cr content and microstructure evolution on performance enhancement during the processing stage remain unclear. In this research, Cu-xCr-0.1Zr alloys with varying Cr contents were fabricated via the thermo-mechanical approach. The microstructure evolution, as well as the mechanical and electrical properties before and after aging were investigated. It was discovered that Cr can mitigate the grain deformation degree of the copper alloy during cold rolling, notably augment the proportion of large-angle grain boundaries, and diminish the dislocation density induced by plastic deformation. As the Cr content increases, the conductivity of the sample declines from 86% IACS (0Cr) to 34.1% IACS (1.8Cr), and the tensile strength rises from 435 MPa (0Cr) to 542 MPa (1.8Cr) after cold rolling; the conductivity decreases from 89.4% IACS (0Cr) to 77.3% IACS (1.8Cr), and the tensile strength increases from 278 MPa to 607 MPa (1.0Cr). Based on the comprehensive outcomes, the aged 1.0Cr sample, with a tensile strength of 607 MPa and a conductivity of 80.9% IACS, satisfies the performance requirements of high-strength and high-conductivity copper alloys.
This study systematically investigated the thermal deformation characteristics of industrial-grade Q690 HSLA steel under different temperatures and strain rates through isothermal compression tests conducted on the Gleeble-3500 simulator. The flow stress of Q690 steel exhibits significant sensitivity to deformation parameters (850–1150 °C and 0.001–10 s−1), characterized by a pronounced thermal softening effect at higher temperatures and strain-rate hardening as the strain rate increases. Through the construction of processing maps, we identified an optimal processing window within the temperature range of 1000–1100 °C and strain rates of 0.01–0.1 s−1, where the power dissipation efficiency (η) reaches a peak of 0.34, indicating superior hot workability. Conversely, flow instability zones were predominantly observed at lower temperatures and higher strain rates, with these regions expanding as strain increased. By integrating flow curve analysis, instability criteria, and microstructural characterization, we determined that complete dynamic recrystallization (DRX) is achieved at 1050 °C and 0.1 s−1. Under these conditions, the material exhibits a refined, homogeneous equiaxed grain structure with uniform martensitic laths and an average prior austenite grain size of approximately 9.88 µm.