Thermoplastic polyurethane (TPU) composites with eutectic gallium (Ga) and indium (In) (eGaIn) fillings of 0 wt%–75 wt% were prepared using the electrostatic spinning method. Field emission scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier-transform infrared (FTIR) spectroscopy were used to characterize the eGaIn NDs/TPU composites. To evaluate their X-ray shielding properties, Phy-X/PSD and WinXCom were employed to calculate the mass attenuation coefficients, linear attenuation coefficients, half-value layers, tenth value layers, mean free paths, and adequate atomic numbers of the eGaIn NDs/TPU composites. The SEM results indicated that the eGaIn nanodroplets were evenly distributed throughout the TPU fibers, and the flowable eGaIn was well-suited for interfacial compatibility with the TPU. A comparison of the eGaIn NDs/TPU composites with different content levels showed that the composite with 75 wt% eGaIn had the highest μm at all the evaluated energies, indicating a superior ability to attenuate X-rays. This non-toxic, lightweight, and flexible composite is a potential material for shielding against medical diagnostic X-rays.
In the tritium breeding blanket of nuclear fusion reactors, the heat transfer behavior and thermal-mechanical response of the tritium breeder pebble bed are affected by the inner packing structure, which is crucial for the design and optimization of a reliable pebble bed in tritium breeding blanket. Thus, the effect of pebble size distribution and fixed wall effect on packing structure and contact force in the poly-disperse pebble bed were investigated by numerical simulation. The results show that pebble size distribution has a significant influence on the inner packing structure of pebble bed. With the increase of the dispersion of pebble size, the average porosity and the average coordination number of the poly-disperse pebble bed gradually decrease. Due to the influence of the fixed wall, the porosity distribution of the pebble bed shows an obvious wall effect. For poly-disperse pebble bed, the influenced region of the wall effect gradually decreases with the increase of the dispersion of pebble size. In addition, the gravity effect and the pebble size distribution have an obvious influence on the contact force distribution inside the poly-disperse pebble bed. The majority of the contact force are weak contact force that is less than the average contact force. Only a few of pebbles have strong contact force that is greater than average contact force. This investigation can help in analyzing the pebble crushing characteristics and the thermal hydraulic analysis in the poly-disperse tritium breeder pebble bed.
The hydrogen permeation behavior of novel AlCrFeTiNb, AlCrMoNbZr and AlCrFeMoTi high-entropy alloy (HEA) coatings were investigated. The hydrogen permeability of HEA coatings prepared by magnetron sputtering technology were tested using gas-driven deuterium permeation and electrochemical hydrogen permeation methods. The gas-driven permeation results show that the deuterium permeation resistance of the AlCrFeTiNb coating is the worst because of the unstable structure at a high temperature. Scanning electron microscope (SEM) and X-ray Diffraction (XRD) analysis proved a loose surface morphology of the AlCrFeTiNb coating and demonstrated the formation of iron-based oxides after deuterium permeation experiments. A high content of iron in HEA coating is disadvantageous for improving the hydrogen permeability. Differently, electrochemical hydrogen permeation reveals that the AlCrMoNbZr coating could resist hydrogen permeation better in a corrosive environment (0.2 mol/L KOH solution). The AlCrFeMoTi coating was peeled off after an electrochemical hydrogen permeation test due to the poor corrosion resistance. The hydrogen behavior of HEA coatings was discussed in detail. Our study provides a promising thought on hydrogen permeation of HEA coatings.
In a tritium-breeding blanket of a fusion reaction, helium, used as a tritium-purging gas, will purge the tritium breeder pebble beds to extract the tritium in blanket. The purge gas flow characteristics will affect the tritium extraction efficiency. The effect of the fixed wall on the pebble packing structures and purge gas flow characteristics was investigated by combining the discrete element method (DEM) and computational fluid dynamics (CFD) method. The results indicate that the fixed wall leads to a regular packing of the pebbles adjacent to the fixed wall in association with drastic fluctuations in the porosity of the pebble bed, which can affect the purge gas flow behaviors. Further analyses of helium flow behaviors show that the helium pressure in the pebble bed decreases in a linear manner along the flow direction, whereas the pressure drop gradient of helium increases gradually with an increase in the packing factor. The reduction in porosity in the pebble bed leads to a notable escalation in helium flow velocity. Concerning the direction perpendicular to the helium gas flow, the evolution of the cut-plane averaged velocity of helium is similar to that of the porosity, except in the region immediately adjacent to the wall. The pressure drop and flow characteristics obtained in this study can serve as input for the thermohydraulic analysis of the tritium blowing systems in the tritium-breeding blanket of a fusion reactor.
The flow characteristics of purge gas helium in the pebble bed of the tritium breeding blanket are important in analyzing the tritium purging process and optimizing the design of the solid breeder blanket. Therefore, the flow characteristics of helium gas in randomly packed pebble beds are investigated experimentally with a focus on the analysis of the pressure loss distribution. The results show that gas velocity, bed dimension, and pebble diameters have an obvious influence on the helium flow characteristics in pebble beds. With the increase in the inlet helium gas velocity, the pressure drop gradient of helium in the pebble bed gradually increased. With increases in the pebble bed dimension, the pressure drop gradient of helium in the pebble bed gradually increased. With the increase in the pebble diameter, the pressure drop gradient gradually decreased. In addition, the effect of temperature on the pressure drop of helium in the pebble bed was also preliminarily investigated. The pressure drop gradient of the helium through the pebble bed obviously increased with the increase in the helium and the bed temperature. The experimentally obtained pressure loss characteristics can be used for the validation of the simulation of a blanket pebble bed and as input parameters in the thermo-hydraulic analysis of solid-tritium breeder blankets.
The packing characteristics of a pebble bed are essential to understand the heat- and mass-transfer processes occurring within a granular system. Therefore, the packing characteristics of rectangular prismatic pebble beds randomly packed with mono-sized pebbles are analyzed. In terms of the average and local packing fraction distribution, coordination number, and radial distribution function, the effects of the rectangular tube aspect ratio and cross-sectional area on the packing properties of pebble beds are explored in depth. The findings indicate that the packing structures of the rectangular pebble bed exhibit noticeable fixed-wall effects. The average packing fraction and coordination number gradually decline as the rectangular tube aspect ratio rises. Close to the fixed wall, a noticeable wall effect can be seen in the distribution of axial and local packing fractions and the pebble center distribution. The wall effect has an increasing effect on the axial and local packing fraction distributions in rectangular tubes with increasing aspect ratios. Additionally, the average packing fraction and the average coordination number also increase as the cross-sectional area increases, indicating a gradual weakening of the wall effect as the cross-sectional area increases. Furthermore, the cross-sectional area and aspect ratio of the rectangular tubes affect the RDF values of the rectangular pebble beds but have no impact on the RDF features. The findings reported in this paper will be helpful for designing and optimizing pebble beds in the breeding blanket of fusion reactors.