The need to tackle the urban heat island effect demands the implementation of cool surfaces as a mitigation strategy. This study comprehensively reviews the evolution of this research field from a materials perspective. It provides a bibliometric analysis of the relevant literature using the SciMAT software processing of bibliographic records from 1995 to 2020, for the evolution of cool surfaces. The results obtained show an increased interest in the field from 2011 to 2020, particularly for roof applications, and present the scientific evolution of reflective materials. According to the materials dimension adopted by the development of the research field, the study is refined from a bibliometric analysis of 982 selected records for the analysis of five themes: (i) Pigments; (ii) Phase change materials; (iii) Retroreflective materials; (iv) Ceramic materials; and (v) Glass. These materials present promising results in terms of their solar reflectance performances in the mitigation of the urban heat island phenomenon. At the end of this review, recommendations for future studies are provided for the creation of economic and environmentally friendly materials based on waste glass recycling. This study represents a valuable contribution that provides a scientific background with regard to cool surfaces from a materials perspective for future investigations.
Glass wastes that come from recycling plants do not often find a proper use, thus, they are discarded. In order to find future uses for these wastes, this paper explores the characterization of waste glasses (WGs) as a raw material through the assessment of their light reflectance if they were used for external coatings in building materials. To this aim, in this research, several clay-tile specimens were fabricated and coated with three different compositions of waste glass. For these specimens, three variables were analyzed to serve for this WG-based coating characterization: thickness of WG coating, temperature, and holding time of burning. The resulting WG-coated tiles were assessed in terms of the light spectral reflectance and whiteness index, with the help of a fiber optic spectrometer. Results show that the composition of WG had a very significant influence on the light spectral reflectance and the degree of whiteness, with holding time and WG thickness being the most influential depending on the WG type. The temperature of burning was also shown to be critical for the densification process. Finally, an interpretation of these results based on the WG chemical composition coatings obtained by XRF is discussed in this paper.
The crushing of the glass fiber-reinforced polymer (GFRP) previously separated from the other wind-turbine-blade materials produces a waste with minimum contents of deformable particles of balsa wood and polymers, being mainly composed of GFRP-composite fibers. This residue is named selectively crushed wind-turbine blade (SCWTB). This research evaluates the impact of adding up to 6.0% by volume of SCWTB on the deformability, load-bearing capacity and energy absorption of concrete subjected to compression, bending, and indirect-tensile stresses. SCWTB increased the failure strain of concrete in the direction parallel to a compression load, although it led the failure and fracture strains to match. However, the strain increase from failure to fracture was 2000–3000 µε in the transverse direction to loading, so concrete with SCWTB was load-bearing after failure. GFRP-composite fibers’ stitching effect was more noticeable under bending stresses. Thus, 1.5% vol. and 6.0% vol. SCWTB resulted in almost the same bending failure stress in concrete, around 6.1–6.2 MPa, and contents from 3.0 and 6.0% vol. SCWTB provided load-bearing capacity in simple and notched-specimen bending, respectively. In addition, the low content of deformable particles in SCWTB increased the deflection increment from failure to fracture in bending, although the presence of such particles augmented energy absorption. No SCWTB content provided load-bearing capacity under indirect-tensile stresses, although it did increase pre-failure deformability. In general, the energy absorbed by concrete increased by up to 43% when adding SCWTB, the use of up to 6.0% of this waste being recommended to increase the ductility of concrete. Graphical abstract
9 July 2026 in International Journal of Pavement Research and Technology
Recycled fibers in bituminous mixtures are increasingly recognized for their potential to modify and reinforce asphalt mixtures, enhancing durability and reducing environmental impacts. This paper reviews the influencing themes and factors related to the incorporation of recycled fibers into bituminous mixtures, based on a systematic bibliometric analysis. A bibliometric study was conducted covering the evolution of document publications, sources, authors, countries, and the clustering of influential keywords, which frame the main themes explored in a systematic literature review. Results reveal a growing interest in case studies assessing the mechanical performance of bituminous mixtures incorporating recycled fibers, highlighting sustainability and reinforcement design development. The review discusses the main factors influencing mixture reinforcement design, the processing methods and characterization of recycled fibers, and the mechanical performance of different fiber types including plastic, plant-based, textile, and glass fibers. Overall, this work provides insights into the key factors in the literature influencing the performance of recycled fiber-reinforced bituminous mixtures and serves as a preliminary guide and reference for researchers entering this field of study.