The effect of free volume on the process of crystallization of an Al87Ni8Gd5 amorphous alloy is investigated. The deformation of the amorphous alloys leads to the formation of shear bands, which contain an enhanced free volume concentration. To retain the free volume the amorphous alloy was coated with a layer of a refractory metal. The structure of the Al87Ni8Gd5 alloy with a protective Ta coating was studied by X-ray diffraction and transmission electron microscopy methods. The fraction of the nanocrystalline phase formed in the amorphous samples with a protective Ta coating under annealing was found to be larger than that in the uncoated samples. The size of Al nanocrystals formed in the coated and uncoated samples is the same. A higher rate of crystal nucleation in the deformed amorphous samples with a protective coating is caused by a higher diffusion coefficient due to an enhanced free volume concentration.
The effect of protective coatings on the crystallization of amorphous Co-based alloys was studied using the methods of X-ray diffraction, differential scanning calorimetry, and transmission electron microscopy. The crystallization of the amorphous alloys was studied on as-prepared samples, deformed samples, and deformed samples with a protective coating. After heat treatment, the fraction of the crystalline phase in the pre-deformed samples was higher than in the undeformed samples. When using a protective coating, the fraction of nanocrystals formed during heat treatment increased. The size of the crystals formed in deformed samples was smaller, and in the deformed samples with a protective coating, they were slightly larger than in the corresponding initial samples. The reasons for the differences in the formed structure in the amorphous alloys under study are discussed in terms of free volume.
The effect of free volume on the crystallization of amorphous Fe78Si13B9 ribbons was studied using ultrasonic and thermal treatments. To maintain free volume under heating, amorphous samples were coated with a special protective Ta coating. It has been shown via X-ray diffraction that the fraction of the crystalline phase in the annealed coated amorphous ribbons is higher than in the corresponding uncoated samples. The use of ultrasonic treatment and the application of a protective coating lead to the formation of a larger proportion of the crystalline phase during annealing. Differences in crystallization kinetics are discussed under the assumption that the concentration of free volume in amorphous samples affects their crystallization, as well as the role of the Ta coating preventing the release of free volume to the surface during heat treatment.
8 December 2023 in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
The influence of the free volume on the crystallization processes of Fe78Si13B9 and Al87Ni8Gd5 amorphous alloys is studied by X-ray diffraction. To study the influence of the free volume, two methods of amorphous-alloy deformation are carried out: ultrasonic treatment and multiple rolling. After deformation, a protective coating is applied to the amorphous alloys. It is shown that the deposition of a protective coating with a higher vacancy-formation energy compared to that in the amorphous alloys under study is an effective way to maintain the free volume in the amorphous phase, since it is thermodynamically unfavorable for the free volume to migrate from the amorphous phase into the coating material. Experimental data indicate that the preliminary deformation of amorphous alloys leads to an increase in the amount of free volume. An increase in the amount of free volume and its maintenance by the protective coating contributes to the significant crystallization acceleration of Fe78Si13B9 and Al87Ni8Gd5 amorphous alloys. The results obtained expand existing ideas about the processes of the crystallization of amorphous alloys and indicate the possibility of developing materials with different structural characteristics and, consequently, with different physical–chemical properties.
1 November 2023 in Poverhnostʹ. Rentgenovskie, sinhrotronnye i nejtronnye issledovaniâ
The influence of the free volume on the crystallization processes of Fe78Si13B9 and Al87Ni8Gd5 amorphous alloys was studied by X-ray diffraction. To study the influence of the free volume, two methods of amorphous alloys deformation were carried out: ultrasonic treatment and multiple rolling. After deformation, a protective coating was applied to the amorphous alloys. It is shown that the deposition of a protective coating with a higher vacancy formation energy compared to the vacancy formation energy in the amorphous alloys under study is an effective way to maintain the free volume in the amorphous phase, since it is thermodynamically unfavorable for the free volume to migrate from the amorphous phase into the coating material. Experimental data indicate that the preliminary deformation of amorphous alloys leads to an increase in the amount of free volume. An increase in the amount of free volume and its maintenance by protective coating contributes to a significant crystallization acceleration of Fe78Si13B9 and Al87Ni8Gd5 amorphous alloys. The results obtained expand the existing ideas about the processes of crystallization of amorphous alloys and indicate the possibility of developing materials with different structural characteristics and, consequently, with different physicochemical properties.
1 April 2025 in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
The surface morphology and structure of the amorphous Al88Ni10Y2 alloy subjected to deformation by multiple cold rolling were studied using X-ray diffraction and scanning electron microscopy. It was shown that during plastic deformation, steps are formed on the surface of the amorphous alloy due to the emergence of shear bands on the surface. It was found that aluminum crystals are formed in the deformed alloy. The steps on the surface of the deformed alloy were analyzed using the images obtained by the scanning electron microscopy method. It was shown that the length of the steps remains approximately the same when examining the surface of different areas of the deformed alloy. An assessment was made of the change in the fraction of free volume in the studied alloy during plastic deformation. The applied methodology made it possible to assess the difference in the density of undeformed and deformed alloys of different compositions using electron microscopic images. Determining the change in free volume content in amorphous alloys subjected to plastic deformation is a key factor in studying the ways of forming amorphous-nanocrystalline structures with improved mechanical properties.