This paper investigates the accuracy of deriving the composite optical constants of binary mixtures from only the complex indices of refraction of the neat materials. These optical constants enable the reflectance spectra of the binary mixtures to be modeled for multiple scenarios (e.g., different substrates, thicknesses, volume ratios), which is important for contact and standoff chemical detection. Using volume fractions, each mixture's complex index of refraction was approximated via three different mixing rules. To explore the impact of intermolecular interactions, these predictions are tested by experimental measurements for two representative sets of binary mixtures: (1) tributyl phosphate combined with n-dodecane, a non-polar medium, to represent mixtures which primarily interact via dispersion forces and (2) tributyl phosphate and 1-butanol to represent mixtures with polar functional groups that can also interact via dipole–dipole interactions, including hydrogen bonding. The residuals and the root-mean-square error between the experimental and calculated index values are computed and demonstrate that for miscible liquids in which the average geometry of the cross-interactions can be considered isotropic (e.g., dispersion), the refractive indices of the mixtures can be modeled using composite n and k values derived from volume fractions of the neat liquids. Conversely, in spectral regions where the geometry of the cross-interactions is more restricted and anisotropic (e.g., hydrogen bonding), the calculated n and k values vary from the measured values. The impact of these interactions on the reflectance spectra are then compared by modeling a thin film of the binary mixtures on an aluminum substrate using both the measured and the mathematically computed indices of refraction.
Obtaining the complex refractive index vectors n(ν~) and k(ν~) allows calculation of the (infrared) reflectance spectrum that is obtained from a solid in any of its many morphological forms. We report an adaptation to the KBr pellet technique using two gravimetric dilutions to derive quantitative n(ν~)/k(ν~) for dozens of powders with greater repeatability. The optical constants of bisphenol A and sucrose are compared to those derived by other methods, particularly for powdered materials. The variability of the k values for bisphenol A was examined by 10 individual measurements, showing an average coefficient of variation for k peak heights of 5.6%. Though no established standards exist, the pellet-derived k peak values of bisphenol A differ by 11% and 31% from their single-angle- and ellipsometry-derived values, respectively. These values provide an initial estimate of the precision and accuracy of complex refractive indices that can be derived using this method. Limitations and advantages of the method are discussed, the salient advantage being a more rapid method to derive n/k for those species that do not readily form crystals or specular pellets.
Forest fires spread via production and combustion of pyrolysis gases in the understory. The goal of the present paper is to understand the spatial location, distribution, and fraction (relative to the overstory) of understory plants, in this case, sparkleberry shrub, namely its degree of understory consumption upon burn, and to search for correlations between the degree of shrub consumption to the composition of emitted pyrolysis gases. Data were collected in situ at seven small experimental prescribed burns at Ft. Jackson, an army base in South Carolina, USA. Using airborne laser scanning (ALS) to map overstory tree crowns and terrestrial laser scanning (TLS) to characterize understory shrub fuel density, both pre- and postburn estimates of sparkleberry coverage were obtained. Sparkleberry clump polygons were manually digitized from a UAV-derived orthoimage of the understory and intersected with the TLS point cloud-derived rasters of pre- and postburn shrub fuel bulk density; these were compared in relation to overstory crown cover as well as to ground truth. Shrub fuel consumption was estimated from the digitized images; sparkleberry clump distributions were generally found to not correlate well to the overstory tree crowns, suggesting it is shade-tolerant. Moreover, no relationship was found between the magnitude of the fuel consumption and the chemical composition of pyrolysis gases, even though mixing ratios of 25 individual gases were measured.
We document an artifact associated with the back reflection from samples or sampling accessories in Fourier transform spectrometers. Samples oriented normal to the incoming modulated beam can reflect light back to the interferometer and this light (the percentage dependent on the sample’s refractive index) is modulated by the interferometer a second time resulting in light erroneously appearing at twice its true frequency. The phenomenon occurs across the spectrum but is most apparent when positive-going narrow absorption peaks at 1 f display as negative-going peaks at 2 f. We have redressed the artifact by implementing a rotation stage directly beneath the sample holder: As the stage is rotated through small angles relative to beam normal, the back-reflected light does not enter the interferometer and the artifact disappears. The observation is relevant to several IR sampling methods: gas/liquid cells, alkali halide pellets, reflectance accessories, etc.
30 November 2022 in International Journal of Wildland Fire
Background: Fire models use pyrolysis data from ground samples and environments that differ from wildland conditions. Two analytical methods successfully measured oxidative pyrolysis gases in wind tunnel and field fires: Fourier transform infrared (FTIR) spectroscopy and gas chromatography with flame-ionisation detector (GC-FID). Compositional data require appropriate statistical analysis. Aims: To determine if oxidative pyrolysis gas composition differed between analytical methods and locations (wind tunnel and field). Methods: Oxidative pyrolysis gas sample composition collected in wind tunnel and prescribed fires was determined by FTIR and GC/FID. Proportionality between gases was tested. Analytical method and location effects on composition were tested using permutational multivariate analysis of variance and the Kruskal–Wallis test. Key results: Gases proportional to each other were identified. The FTIR composition differed between locations. The subcomposition of common gases differed between analytical methods but not between locations. Relative amount of the primary fuel gases (CO, CH4) was not significantly affected by location. Conclusions: Composition of trace gases differed between the analytical methods; however, each method yielded a comparable description of the primary fuel gases. Implications: Both FTIR and GC/FID methods can be used to quantify primary pyrolysis fuel gases for physically-based fire models. Importance of the trace gases in combustion models remains to be determined.