Oleg Igorevich Lebedev

Dr. Oleg Igorevich Lebedev

Laboratory CRISMAT, UMR 6508, CNRS-ENSICAEN, Université de Caen, 6Bd Marechal Juin 14050 Caen, France

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 September 2017 in Sensors
Verified
Journal Article
Open access
PDF file
SVSvetlana Vladimirova
Svetlana Vladimirova
VKValeriy Krivetskiy
Valeriy Krivetskiy
Marina RumyantsevaMarina Rumyantseva
Marina Rumyantseva
Alexander M. GaskovAlexander M. Gaskov
Alexander M. Gaskov
NMNatalia Mordvinova
Natalia Mordvinova
PFPavel Forsh
Pavel Forsh
Nanocrystalline cobalt oxide Co3O4 has been prepared by precipitation and subsequent thermal decomposition of a carbonate precursor, and has been characterized in detail using XRD, transmission electron microscopy, and FTIR spectroscopy. The sensory characteristics of the material towards carbon monoxide in the concentration range 6.7–20 ppm have been examined in both dry and humid air. A sensor signal is achieved in dry air at sufficiently low temperatures T = 80–120 °C, but the increase in relative humidity results in the disappearance of sensor signal in this temperature range. At temperatures above 200 °C the inversion of the sensor signal in dry air was observed. In the temperature interval 180–200 °C the sensor signal toward CO is nearly the same at 0, 20 and 60% r.h. The obtained results are discussed in relation with the specific features of the adsorption of CO, oxygen, and water molecules on the surface of Co3O4. The independence of the sensor signal from the air humidity combined with a sufficiently short response time at a moderate operating temperature makes Co3O4 a very promising material for CO detection in conditions of variable humidity.

11 May 2015 in Materials
Verified
Journal Article
Open access
PDF file
PMPatrick R. N. Misse
Patrick R. N. Misse
David BerthebaudDavid Berthebaud
David Berthebaud
Oleg Igorevich LebedevOleg Igorevich Lebedev
Oleg Igorevich Lebedev
AMAntoine Maignan
Antoine Maignan
EGEmmanuel Guilmeau
Emmanuel Guilmeau
A solid solution of Ti1 − xNbxS3 composition (x = 0, 0.05, 0.07, 0.10) was synthesized by solid-liquid-vapor reaction followed by spark plasma sintering. The obtained compounds crystallize in the monoclinic ZrSe3 structure type. For the x = 0.07 sample, a mixture of both A and B variants of the MX3 structure is evidenced by transmission electron microscopy. This result contrasts with those of pristine TiS3, prepared within the same conditions, which crystallizes as a large majority of A variant. Thermoelectric properties were investigated in the temperature range 323 to 523 K. A decrease in the electrical resistivity and absolute value of the Seebeck coefficient is observed when increasing x due to electron doping. The lattice component of the thermal conductivity is effectively reduced by the Nb for Ti substitution through a mass fluctuation effect and/or a disorder effect created by the mixture of both A and B variants. Due to the low carrier concentration and the semiconductor character of the doped compounds, the too low power factor values leads to ZT values that remain smaller by a factor of 50 than those of the TiS2 layered compound.

12 May 2022 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
SHSangki Hong
Sangki Hong
ADAida M. Díez
Aida M. Díez
AAAdedoyin N. Adeyemi
Adedoyin N. Adeyemi
JSJuliana P. S. Sousa
Juliana P. S. Sousa
LSLaura Salonen
Laura Salonen
JZJulia Zaikina
Julia Zaikina
Oxide perovskites have attracted great interest as materials for energy conversion due to their stability and structural tunability. La-based perovskites of 3d-transition metals have demonstrated excellent activities as electrocatalysts in water oxidation. Herein, we report the synthesis route to La-based perovskites using an environmentally friendly deep eutectic solvent (DES) consisting of choline chloride and malonic acid. The DES route affords phase-pure crystalline materials on a gram scale and results in perovskites with high electrocatalytic activity for oxygen evolution reaction. A convenient, fast, and scalable synthesis proceeds via assisted metathesis at a lower temperature as compared to traditional solid-state methods. Among LaCoO3, LaMn0.5Ni0.5O3, and LaMnO3 perovskites prepared via the DES route, LaCoO3 was established to be the best-performing electrocatalyst for water oxidation in alkaline medium at 0.25 mg cm-2 mass loading. LaCoO3 exhibits current densities of 10, 50, and 100 mA cm-2 at respective overpotentials of approximately 390, 430, and 470 mV, respectively, and features a Tafel slope of 55.8 mV dec-1. The high activity of LaCoO3 as compared to the other prepared perovskites is attributed to the high concentration of oxygen vacancies in the LaCoO3 lattice, as observed by high-resolution transmission electron microscopy. An intrinsically high concentration of O vacancies in the LaCoO3 synthesized via the DES route is ascribed to the reducing atmosphere attained upon thermal decomposition of the DES components. These findings will contribute to the preparation of highly active perovskites for various energy applications.

2 May 2012 in Journal of Physics: Condensed Matter
Verified
Journal Article
Closed access
KSKiran Singh
Kiran Singh
AMAntoine Maignan
Antoine Maignan
CSCharles Simon
Charles Simon
SKSanjay Kumar
Sanjay Kumar
CMChristine Martin
Christine Martin
GTG Van Tendeloo
G Van Tendeloo
The complex dielectric susceptibility and spin glass properties of polycrystalline CuCr(0.5)V(0.5)O(2) delafossite have been investigated. Electron diffraction, high resolution electron microscopy and electron energy loss spectroscopy show that the Cr(3+) and V (3+) magnetic cations are randomly distributed on the triangular network of CdI(2)-type layers. In contrast to CuCrO(2), CuCr(0.5)V(0.5)O(2) exhibits two distinctive (magnetic and electric) glassy states evidenced by memory effects in electric and magnetic susceptibilities. A large magnetodielectric coupling is observed at low temperature.

27 January 2022 in Molecules
Verified
Journal Article
Open access
PDF file
FBFaranak Bahrami
Faranak Bahrami
MAMykola Abramchuk
Mykola Abramchuk
Oleg Igorevich LebedevOleg Igorevich Lebedev
Oleg Igorevich Lebedev
FTFazel Tafti
Fazel Tafti
Nearly two decades ago, Alexei Kitaev proposed a model for spin-1/2 particles with bond-directional interactions on a two-dimensional honeycomb lattice which had the potential to host a quantum spin-liquid ground state. This work initiated numerous investigations to design and synthesize materials that would physically realize the Kitaev Hamiltonian. The first generation of such materials, such as Na2IrO3, α-Li2IrO3, and α-RuCl3, revealed the presence of non-Kitaev interactions such as the Heisenberg and off-diagonal exchange. Both physical pressure and chemical doping were used to tune the relative strength of the Kitaev and competing interactions; however, little progress was made towards achieving a purely Kitaev system. Here, we review the recent breakthrough in modifying Kitaev magnets via topochemical methods that has led to the second generation of Kitaev materials. We show how structural modifications due to the topotactic exchange reactions can alter the magnetic interactions in favor of a quantum spin-liquid phase.

9 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
VSViviana Sousa
Viviana Sousa
GSGuillaume Savelli
Guillaume Savelli
Oleg Igorevich LebedevOleg Igorevich Lebedev
Oleg Igorevich Lebedev
KKKirill Kovnir
Kirill Kovnir
JCJosé Higino Correia
José Higino Correia
YKYury V. Kolen'Ko
Yury V. Kolen'Ko
Thin-film thermoelectrics (TEs) with a thickness of a few microns present an attractive opportunity to power the internet of things (IoT). Here, we propose screen printing as an industry-relevant technology to fabricate TE thin films from colloidal PbSe quantum dots (QDs). Monodisperse 13 nm-sized PbSe QDs with spherical morphology were synthesized through a straightforward heating-up method. The cubic-phase PbSe QDs with homogeneous chemical composition allowed the formulation of a novel ink to fabricate 2 μm-thick thin films through robust screen printing followed by rapid annealing. A maximum Seebeck coefficient of 561 μV K−1 was obtained at 143 °C and the highest electrical conductivity of 123 S m−1 was reached at 197 °C. Power factor calculations resulted in a maximum value of 2.47 × 10−5 W m−1 K−2 at 143 °C. To the best of our knowledge, the observed Seebeck coefficient value is the highest reported for TE thin films fabricated by screen printing. Thus, this study highlights that increased Seebeck coefficients can be obtained by using QD building blocks owing to quantum confinement.