We study the influence of He⁺ irradiation induced interface intermixing on magnetic domain wall (DW) dynamics in W-CoFeB (0.6 nm)-MgO ultrathin films, which exhibit high perpendicular magnetic anisotropy and large Dzyaloshinskii-Moriya interaction (DMI) values. Whereas the pristine films exhibit strong DW pinning, we observe a large increase in the DW velocity in the creep regime upon He⁺ irradiation, which is attributed to the reduction of pinning centers induced by interface intermixing. Asymmetric in-plane field-driven domain expansion experiments show that the DMI value is slightly reduced upon irradiation, and a direct relationship between DMI and interface anisotropy is demonstrated. Our findings provide insights into the material design and interface control for DW dynamics, as well as for DMI, enabling the development of high-performance spintronic devices based on ultrathin magnetic layers.

[Pt(1.5 nm)/Co(t_Co)/W(1.5 nm)]_N multilayers of different Co thicknesses (t_Co) and number of repeats (N) have been grown by sputtering on Si substrates, and their magnetic properties have been studied. The x-ray reflectivity has been used to measure thicknesses of each layer as well as their roughness. The dependence of the magnetic moment on t_Co and N (as determined by vibrating sample magnetometry) indicates the existence of a magnetic dead layer, which increases with N and reaches its maximum values for N ≥ 3. A similar N dependence of the magnetization at saturation is found. Ferromagnetic resonance and Brillouin light scattering have been used to investigate perpendicular magnetic anisotropy, damping, and interfacial Dzyaloshinskii-Moriya interaction (iDMI) vs Co thickness and the number of Pt/Co/W sequence repeats. We show that these parameters result from interface contributions that vary in a similar way with N, confirming that the first two Pt/Co/W trilayers are of lower quality. We thus conclude that for these systems, the increase of N improves the quality of interfaces and the volume of the stack, leading to the enhancement of the magnetic properties. Moreover, the measured weak iDMI constant, even for the higher N values, suggests that most probably, this iDMI results mainly from the Pt/Co interfaces.

In this work, we present the magneto-ionic response to ionic liquid gating in Ta/CoFeB/MgO/HfO₂ stacks, where heavy metal dusting layers of Ta, W, and Pt are inserted at the Ta/CoFeB and CoFeB/MgO interfaces. Dusting layers of W inserted at the Ta/CoFeB interface increase perpendicular magnetic anisotropy (PMA) by more than 50%, while no significant changes are seen for Pt. In these samples, gating cannot break the PMA seeded at the CoFeB/MgO interface, only relatively small changes in the coercivity can be induced, about 20% for Ta and Pt and 6% for W. At the CoFeB/MgO interface, a significant quenching of the magnetization is seen when W and Ta dusting layers are inserted, which remains unchanged after gating, suggesting a critical deterioration of the CoFeB. In contrast, Pt dusting layers result in an in-plane anisotropy that can be reversibly converted to PMA through magneto-ionic gating while preserving the polycrystalline structure of the MgO layer. This shows that dusting layers can be effectively used not only to engineer magnetic properties in multilayers but also to strongly modify their magneto-ionic performance.

We present experimental and numerical results on the magnetization reversal induced by spin–orbit torques of micronic disks of a ferromagnetic multilayer with perpendicular magnetic anisotropy on top of a Pt track: Pt (6 nm)/[Co(0.2 nm)/Ni(0.6 nm)] × 5/Al(5 nm). The current induced magnetization switching process is probed by anomalous Hall effect measurements and Kerr microscopy. The electrical characterization reveals the critical current for the complete reversal to be about $3\times {10}^{11}$ A/m², and Kerr microscopy uncovers a deterministic nucleation that depends on current and field polarity. Through the use of experimental switching phase diagrams coupled to micromagnetic simulations, we evaluated the field-like to damping-like torque ratio to be 0.73 ± 0.05, which is in good agreement with experimental values observed by second harmonic measurements. These measurements emphasize an unexpectedly large field-like contribution in this relatively thick Co/Ni multilayer (4 nm). In light of these experiments and simulations, we discuss the key parameters needed to understand the magnetization reversal, namely, the field and damping-like torques and the Dzyaloshinskii–Moriya interaction.

The perpendicular magnetic anisotropy (PMA) and the interfacial Dzyaloshinskii–Moriya interaction (iDMI) are investigated in as grown and 300 °C annealed Co-based ultrathin systems. For this, Co films of various thicknesses (0.8 nm ⩽ t _Co ⩽ 5.7 nm) were deposited by magnetron sputtering on thermally oxidized Si substrates using Pt, W, Ir, Ti, Ru and MgO buffer or/and capping layers. X-ray diffraction was used to investigate their structural properties and vibrating sample magnetometry (VSM) was used to determine the magnetic dead layer thickness and the magnetization at saturation ( M _s ). VSM revealed that the M _s for the Pt and the Ir buffered and capped films is the largest. Microstrip line ferromagnetic resonance (MS-FMR), used to extract the gyromagnetic ratio of the thicker Co films, revealed the existence of a second order PMA term, which is thickness dependent. Brillouin light scattering (BLS) in the Damon–Eshbach configuration was used to investigate the thickness dependence of the iDMI effective constant from the spin wave vector dependence of the frequency difference between Stokes and anti-Stokes lines. BLS and MS-FMR techniques were combined to measure the spin wave frequency variation as a function of the in-plane applied magnetic field (where the second order PMA contribution vanishes). The thickness dependence of the effective magnetization was then deduced and used to investigate PMA. For all the systems, PMA results from interface and volume contributions that we determined. The largest interface PMA constants were obtained for Pt- and Ir-based systems due to the electron hybridization of Co with these heavy metals having high spin orbit coupling. Annealing at 300 °C increases both the interface PMA and iDMI for the Pt/Co/MgO most probably due to de-mixing of interpenetrating oxygen atoms from the Co layer and the formation of a sharp Co/O interface.

Ir and Pt thickness dependences of the interfacial Dzyaloshinskii-Moriya interaction (iDMI), the perpendicular magnetic anisotropy (PMA), and the damping in Co-based systems grown by sputtering on Si substrates, using Ir or Pt under or overlayer of variable thickness ($0\le t_{\mathrm{Pt}}\le 3.5\mathrm{nm}$ and $0\le t_{\mathrm{Ir}}\le 1.5\mathrm{nm}$), were investigated using Brillouin light scattering. Vibrating sample magnetometry measurements revealed a significant decrease of the areal magnetic moment at saturation as the thickness $t_{\mathrm{Pt}}$ or $t_{\mathrm{Ir}}$ of the overlayer increases, most likely due to the increasing intermixing. The intermixing, found to be negligible for Ir and Pt underlayers, is stronger for Ir than Pt overlayers. Damping measurements for Pt-based systems allowed us to conclude with the strong spin-pumping contribution. The analysis of the $t_{\mathrm{Pt}}$ dependence of damping, within the spin-pumping model, allowed us to determine the spin-diffusion length of Pt, found to be greater when Pt is used as an underlayer. The $t_{\mathrm{Pt}}$ dependence of the effective PMA and iDMI constants, for which similar trends to that of damping were observed, were qualitatively analyzed to separate the contribution of each interface with Co. It was found that these constants are stronger when Co is grown on Pt, most probably due to weaker intermixing at the Pt/Co interface. Linear dependence of damping vs the PMA effective constant was evidenced, confirming their relationship with spin-orbit coupling (SOC). A linear variation of the PMA effective constant vs the iDMI constant was observed in systems using Pt underlayer, whereas quadratic or linear correlations are possible when Pt is used as an overlayer, probably due to change of the interface SOC by the strong intermixing at the Co/Pt interface. The qualitative analysis of the Ir thickness dependence of iDMI and PMA constants revealed a significant (weak) contribution of the Ir/Co interface to PMA (iDMI). The surface iDMI constant of the Co/Ir interface was estimated to be 0.4 ± 0.1 pJ/m, which confirms the similar iDMI sign of Co/Ir and Co/Pt interfaces.