Yoon Jae Moon

Mr. Yoon Jae Moon

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 March 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AHARIF HUSSAIN
ARIF HUSSAIN
HLHee Lak Lee
Hee Lak Lee
YMYoon Jae Moon
Yoon Jae Moon
HKHeuiseok Kang
Heuiseok Kang
SMSeung-Jae Moon
Seung-Jae Moon
JHJun Young Hwang
Jun Young Hwang
During the thermal sintering of metal nanoparticles (NPs) the process temperature plays the most important role in the outcome of the sintering results and the selection of a suitable substrate. Here, temperature calculation during pulsed laser sintering of silver (Ag) nanoparticles (NPs) inkjet-printed on glass substrates is presented. During the pulsed laser sintering of Ag NPs, a minimum line resistivity less than twice the bulk silver resistivity was obtained within around 52 s under a laser power of 276 mW. The temperature field during the pulsed laser sintering of Ag NPs was estimated via a three-dimensional numerical model in which a temperature-dependent thermal conductivity of Ag NPs was adopted. An algorithm for treating the thermal conductivity of the heated Ag NPs in a region by a previous laser shot was devised for the improvement of the temperature field estimation. A maximum temperature of approximately 204 °C over the Ag NPs line was obtained with a 276 mW laser power and a scanning speed of 135 μm/s.

20 February 2024 in Materials
Verified
Journal Article
Open access
PDF file
HPHyeong-Jin Park
Hyeong-Jin Park
KRKyongtae Ryu
Kyongtae Ryu
HLHee Lak Lee
Hee Lak Lee
YMYoon Jae Moon
Yoon Jae Moon
JHJun Young Hwang
Jun Young Hwang
SMSeung-Jae Moon
Seung-Jae Moon
The influence of nanoparticle (NP) size on the physical characteristics of sintered silver NP ink was studied using four different types of inks. The Ag NP inks were spin-coated on glass substrates with an average thickness of 300 nm. Each sample was sintered for 30 min, with temperatures from 50 °C to 400 °C by an interval of 50 °C. After sintering, the specific resistance of each case was obtained using the resistance and surface profile measurements. The minimum specific resistance obtained by the experiment was 2.6 μΩ·cm in the case in which 50 nm-sized Ag NP ink was sintered at 350 °C. The transformed surface morphology and grain size of each case were observed using scanning electron microscopy and atomic force microscopy. The results of this study can be a reference for future manufacturers in selecting the Ag NP size and the sintering temperature.

22 November 2021 in Metals
Verified
Journal Article
Open access
PDF file
ILIksang Lee
Iksang Lee
AHARIF HUSSAIN
ARIF HUSSAIN
HLHee Lak Lee
Hee Lak Lee
YMYoon Jae Moon
Yoon Jae Moon
JHJun Young Hwang
Jun Young Hwang
SMSeung-Jae Moon
Seung-Jae Moon
We studied the effect of current supply duration at final-step currents during the stepwise electrical sintering of silver (Ag) nanoparticles (NPs). Ag NPs ink was inkjet-printed onto Eagle-XG glass substrates. Constant final-step currents of 0.4 and 0.5 A with various time intervals were applied to the printed samples. The final-step current of 0.5 A damaged the line at a comparatively shorter time duration. On the other hand, the lower final-step current of 0.4 A prevented the line damage at longer time durations while producing comparatively lower Ag NPs specific resistance. The minimum specific resistances of the printed samples sintered at 0.4 and 0.5 A were 3.59 μΩ∙cm and 3.79 μΩ∙cm, respectively. Furthermore, numerical temperature estimation and scanning electron microscope (SEM) analysis were conducted to elaborate on the results. The numerical temperature estimation results implied that the lower estimated peak temperature at the final-step current of 0.4 A helped prevent Ag NP line damage. The SEM micrographs suggested that a high surface porosity—caused by higher sintering peak temperatures—in the case of the 0.5 A final-step current resulted in a comparatively higher Ag NP line-specific resistance. This contribution is a step forward in the development of Ag NP sintering for printed electronics applications.

14 September 2020 in Coatings
Verified
Journal Article
Open access
PDF file
HKHyungTae Kim
HyungTae Kim
YMYoon Jae Moon
Yoon Jae Moon
HKHeuiseok Kang
Heuiseok Kang
JHJun Young Hwang
Jun Young Hwang
In printed electronics, laser ablation is used to repair defective patterns on transparent, flexible, and thin films, using high-power lasers. The distance between the film surface and laser focus is sensitive to changes as the narrow focus depth of the lens is the range of tens of microns. However, a film fixed on a conductive vacuum chuck (CVC) is always curved, owing to chucking bending; thus, laser focusing must be locally performed before ablation. Therefore, this study proposes a non-contact measurement method for the surface flatness of a transparent and thin film, to compensate for laser defocusing in a large area. The surface flatness was obtained using camera-focus points on the porous surface of the CVC. The focus points were interpolated to achieve a smooth and continuous surface flatness for chucking bending. A laser distance sensor was used to verify the surface flatness from the proposed method. The surface flatness was used to inspect the printed patterns, and to perform laser ablation on the film. The proposed method is advantageous for large-area laser ablation and is expected to become indispensable for repairing machines in printed electronics.

1 June 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
DHDaehee Hyun
Daehee Hyun
HLHee Lak Lee
Hee Lak Lee
YMYoon Jae Moon
Yoon Jae Moon
JHJun Young Hwang
Jun Young Hwang
SMSeung-Jae Moon
Seung-Jae Moon
Thin transparent oxide layers are typically patterned for use in electronic products including semiconductors, displays, and solar cells for applications such as transparent electrodes, insulating films, and encapsulation films. Conventional patterning methods have traditionally been used in photolithography and lift-off processes. Photolithography employs the wet development process, which has disadvantages such as potential undercut effects, swelling, chemical contamination, and high process costs. On the other hand, laser ablation, which has the advantages of high accuracy, high speed, a noncontact nature, and selective processing, can be used to pattern thin films. However, absorption in transparent oxide films is usually low. In this study, experiments were conducted to determine the ablation characteristics of mask layers. The factors affecting ablation, including beam radii, fluences, overlap ratios, and coating thicknesses, were examined; and the parameters characteristic of residue-free ablation, namely the ablation threshold, minimum fluence, and minimum ablation linewidth, were also examined. The experimental results revealed that the beam radius was an important parameter in determining the resolutions of transparent films and substrates.

27 July 2025 in Journal of Measurements in Engineering
Verified
Journal Article
Open access
PDF file
YHYuehua Hu
Yuehua Hu
DSDong Yeol Shin
Dong Yeol Shin
YMYoon Jae Moon
Yoon Jae Moon
JKJaekyun Kim
Jaekyun Kim
KKKyung-Tae Kang
Kyung-Tae Kang
In the inkjet printing process, controlling the droplet size is essential to ensure uniform thin film, a critical factor for achieving high performance of electronic devices. In this study, we evaluate the accuracy and applicability of three droplet measurement methods using inks with different properties. The first method is the laser diffraction method, which measures individual droplets based on the Fraunhofer diffraction in real time. The second is the mass measurement method, which calculates the droplet mass using a microbalance and employs evaporation compensation to minimize evaporation effects, and the third method is the shadow imaging method, a widely adopted commercial technique based on the international standard. To evaluate the accuracy of these measurement methods with three inks having various boiling points (BP), laser diffraction serves as a benchmark here to compare the results of the shadow image and mass measurement methods. Laser diffraction was selected because it shows better coefficient of variation about 1.7 % than the coefficient of variation of mass measurement and shadow imaging methods about 8.7 % and 6.4 %, respectively. The BP of the ink and measurement precision based on laser diffraction results were proportional to each other. These insights guide the selection of optimal measurement method for inkjet printing applications with printed electronic inks. When printed electronic inks with various boiling points were used, the laser diffraction method consistently demonstrated better measurement errors in droplet size than the mass measurement and the shadow imaging method.