This project aims to create a 316L stainless steel coated with a biocomposite based on chitosan for use in the biomedical industry. To completely coat the material, the dip-coating technique was used to apply plain chitosan, chitosan nanosilver, chitosan biotin, and chitosan-nanosilver-biotin in that order. This coating’s surface morphology was investigated with field emission scanning electron microscopy (FESEM). Surface roughness, average size distribution, and 2D and 3D surface tomography were all investigated using scanning probe microscopy and atomic force microscopy (SPM and AFM). The Fourier transform infrared (FTIR) spectroscopy technique was used to quantify changes in functional groups. To evaluate the coated samples’ wettability, contact angle measurements were also performed. The chitosan (CS) + nanosilver, CS + biotin, and CS + biotin + nanosilver-coated 316L stainless steel showed roughness values of about 8.68, 4.21, and 3.3 nm, respectively, compared with the neat chitosan coating, which exhibits 12 nm roughness, indicating a strong effect of biotin and nanosilver on surface topography whereas the coating layers were homogenous, measuring around 33 nm in thickness. For CS + nanosilver and CS + biotin, the average size of agglomerates was approximately 444 nm and 355 nm, respectively. The coatings showed adequate wettability for biomedical applications, were homogeneous, and had no cracks. Their contact angles were around 51–75 degrees. All of these results point to the composite coating’s intriguing potential for use in biological applications.
In this study, we aimed to figure out how the depolymerization of polyethylene terephthalate produces monomers, dimers, trimers, and other oligomers of bis (2-hydroxyethyl) terephthalate. Polymerization was achieved in a bubble column reactor with 0.05 wt% 40–50 nm magnesium oxide nanoparticle as a catalyst. A bubble column reactor was used to perform the recycling process at the boiling point of ethylene glycol and atmospheric pressure. Depolymerized polyethylene terephthalate (DPET) was mixed with poly(methyl methacrylate) and reinforced with 1% Nano Al2O3. The nanoparticles acted as a composite coating in low carbon steel protection. Adhesion strength and mechanical and structural properties were investigated for the composite, and the average coating thickness was 28.39 µm. The results showed that the hardness and adhesion forces between the substrate and composite coating increased with an increase in the amounts of DPET and nano-Al2O3 per polymer resin. On the other hand, the thermal conductivity of the composite coating decreased with the addition of DPET because of an increase in the end chain movement in the composite coating induced by the retardant and an increase in cross-linking force. Furthermore, the bubble column demonstrated outstanding heat and mass transfer phenomena that reduced the reaction time to just 40 min for complete depolymerzation and also reduced energy consumption.
1 January 2024 in Material Design & Processing Communications
Metal matrix nanocomposite coatings are promising for tribological applications given their superior hardness and wear resistance compared to metals. The point of this study was to describe the shape and long‐term performance of nickel‐based coatings that were put on stainless steel using electroless codeposition and made stronger with nanoparticles of zirconia (ZrO2) and alumina (Al2O3). Scanning electron microscopy showed the uniform incorporation of nanoceramics within nickel matrices. Pin‐on‐disk tribotests evaluated wear performance across loads from 5 to 15 N and sliding speeds up to 480 cm/min. Increasing nanoparticle content from 2 to 4 g/L markedly reduced wear rate due to enhanced hardness and density. At all tested loads, Ni‐ZrO2 and Ni‐Al2O3 nanocomposites exhibited considerably lower wear than monolithic nickel. The nanometal matrix particles hindered plastic deformation, with weight losses up to 68% lower than base nickel. Initially, wear resistance rose proportionally with sliding speed resulting from protective oxide layers until abrasive wear prevailed. The nanoparticle reinforcement dramatically extended durability, making it ideal for tribological systems involving mixed or abrasive conditions. More research needs to be done to find the best compositions and other matrix materials to use for these nanoscale strengthening effects.
It is possible to increase the corrosion resistance of a commercially pure titanium substrate while maintaining its excellent mechanical properties using the el
1 July 2025 in Heritage and Sustainable Development
A systematic study was conducted to evaluate the corrosion behavior of a novel magnesium alloy, Mg–Nd–Fe–B, incorporating varying percentages of neodymium magnet scrap. Immersion tests were performed in a sodium chloride (NaCl) solution at room temperature to assess corrosion resistance. The objective was to enhance the corrosion resistance of a new family of lightweight ternary alloys within the Mg–Nd–Fe–B system. X-ray diffraction (XRD) was employed to identify the crystalline phases, while scanning electron microscopy (SEM) was used to examine the microstructure of samples before and after corrosion. The alloys primarily consisted of ?-Mg and Nd?Fe??B phases. Post-corrosion analysis revealed the presence of corrosion products rich in rare earth elements, with the dominant phase being a solid solution of magnesium and neodymium. Corrosion testing showed the formation of a black, neodymium-based surface layer, which acted as a protective barrier. The corrosion rate decreased significantly with increasing magnet scrap content, with the optimal composition (approximately 30 wt%) achieving an 87.3% reduction in corrosion rate compared to alloys with lower magnet content. Additionally, Vickers hardness testing demonstrated a notable improvement in hardness, further supporting the alloy’s suitability for engineering applications. These findings highlight the beneficial role of rare earth elements, particularly neodymium, in improving both the corrosion resistance and mechanical properties of magnesium-based alloys.