Solar photovoltaic energy generation has garnered substantial interest owing to its inherent advantages, such as zero pollution, flexibility, sustainability, and high reliability. Ensuring the efficient functioning of PV power facilities hinges on precise fault detection. This not only bolsters their reliability and safety but also optimizes profits and avoids costly maintenance. However, the detection and classification of faults on the Direct Current (DC) side of the PV system using common protection devices present significant challenges. This research delves into the exploration and analysis of complex faults within photovoltaic (PV) arrays, particularly those exhibiting similar I-V curves, a significant challenge in PV fault diagnosis not adequately addressed in previous research. This paper explores the design and implementation of Support Vector Machines (SVMs) and Extreme Gradient Boosting (XGBoost), focusing on their capacity to effectively discern various fault states in small PV arrays. The research broadens its focus to incorporate the use of optimization algorithms, specifically the Bees Algorithm (BA) and Particle Swarm Optimization (PSO), with the goal of improving the performance of basic SVM and XGBoost classifiers. The optimization process involves refining the hyperparameters of the Machine Learning models to achieve superior accuracy in fault classification. The findings put forth a persuasive case for the Bees Algorithm’s resilience and efficiency. When employed to optimize SVM and XGBoost classifiers for the detection of complex faults in PV arrays, the Bees Algorithm showcased remarkable accuracy. In contrast, classifiers fine-tuned with the PSO algorithm exhibited comparatively lower performances. The findings underscore the Bees Algorithm’s potential to enhance the accuracy of classifiers in the context of fault detection in photovoltaic systems.

Electrical steels play a crucial role in modern electrical devices and power systems due to their exceptional magnetic properties. This comprehensive review delves into the advancements in the field of electrical steels, focusing on key aspects such as microstructure, loss analysis, magnetic properties, alloying elements, and the influence of coatings. The microstructural characteristics of electrical steels are explored in relation to their impact on magnetic behaviour and overall performance. Loss analysis techniques are discussed, highlighting the importance of minimizing energy dissipation in applications. The intricate relationship between magnetic properties and material composition, including the role of alloying elements, is examined to elucidate the mechanisms governing magnetic behaviour. Furthermore, the influence of coatings on the performance of electrical steels is investigated, considering both protection against environmental factors and their impact on magnetic properties. Through a comprehensive synthesis of recent research, this review provides valuable insights into the multifaceted nature of electrical steels and sets the stage for further advancements in their design and application.

This paper focuses on using the Bees Algorithm (BA) to tune the parameters of the proposed Fuzzy Proportional–Integral–Derivative with Filtered derivative (Fuzzy PIDF), Fractional Order PID (FOPID) controller and classical PID controller developed to stabilize and balance the frequency in the Great Britain (GB) power system at rated value. These controllers are proposed to meet the requirements of the GB Security and Quality of Supply Standard (GB-SQSS), which requires frequency to be brought back to its nominal value after a disturbance within a specified time. This work is extended to employ the proposed fuzzy structure controller in a dual-area interconnected power system. In comparison with controllers tuned by Particle Swarm Optimization (PSO) and Teaching Learning-Based Optimization (TLBO) used for the same systems, simulation results show that the Fuzzy PIDF tuned by BA is able to significantly reduce the deviation in the frequency and tie-line power when a sudden disturbance is applied. Furthermore, the applied controllers tuned by BA including the Fuzzy PIDF prove their high robustness against a wide range of system parametric uncertainties and different load disturbances.

In this paper, a combined structure of algorithms based on field-oriented control (FOC) and direct torque control (DTC) is proposed for improving the performance of a three-phase induction motor (IM) over a wide range of torque loads. The objective of this study is to investigate the state-of-the-art research performed on the resilient intersection control management between FOC and DTC algorithms for IM drive. Three algorithms are employed in the proposed scheme: Direct Torque Stator Flux Control (DTSFC), Direct Torque Rotor Flux Control (DTRFC), and the FOC algorithm. The main aim of the control law is to launch the drive system by selecting DTSFC or DTRFC during the transient state while FOC is switched smoothly to the steady-state. The proposed method had several advantages, including the ability to produce torque beyond the pull-out torque range at 340%, high torque dynamics during transient state within 0.5 ms, low chattering up to 0.05 N.m, and fixed frequency at steady-state operation. Furthermore, a comprehensive comparison study has been conducted, including the most recent research, to verify the effectiveness and superiority of the proposed technique. Results were obtained using both MATLAB/Simulink environment and also were experimentally performed by using a dSPACE DS1103 digital signal processing board to verify the concept of the proposed control scheme.

This paper proposes a design of Sliding Mode Control (SMC) for Load Frequency Control (LFC) in a two-area electrical power system. The mathematical model design of the SMC is derived based on the parameters of the investigated system. In order to achieve the optimal use of the proposed controller, an optimisation tool called the Bees Algorithm (BA) is suggested in this work to tune the parameters of the SMC. The dynamic performance of the power system with SMC employed for LFC is studied by applying a load disturbance of 0.2 pu in area one. To validate the supremacy of the proposed controller, the results are compared with those of recently published works based on Fuzzy Logic Control (FLC) tuned by Teaching–Learning-Based Optimisation (TLBO) algorithm and the traditional PID optimised by Lozi map-based Chaotic Optimisation Algorithm (LCOA). Furthermore, the robustness of SMC-based BA is examined against parametric uncertainties of the electrical power system by simultaneous changes in certain parameters of the testbed system with 40% of their nominal values. Simulation results prove the superiority and the robustness of the proposed SMC as an LFC system for the investigated power system.

Fault diagnosis of induction motor anomalies is vital for achieving industry safety. This paper proposes a new hybrid Machine Learning methodology for induction-motor fault detection. Some of the motor parameters such as the stator currents and vibration signals provide a great deal of information about the motor’s conditions. Therefore, these signals of the motor were selected to test the proposed model. The induction motor was assessed in a laboratory under healthy, mechanical, and electrical faults with different loadings. In this study a new hybrid model was developed using the collected signals, an optimal features selection mechanism is proposed, and machine learning classifiers were trained for fault classification. The procedure is to extract some statistical features from the raw signal using Matching Pursuit (MP) and Discrete Wavelet Transform (DWT). Then, the Invasive Weed Optimization algorithm (IWO)-based optimal subset was selected to reduce the data dimension and increase the average accuracy of the model. The optimal subset of features was fed into three classification algorithms: k-Nearest Neighbor (KNN), Support Vector Machine (SVM), and Random Forest (RF), which were trained using k-fold cross-validation to distinguish between the induction motor faults. A similar strategy was performed by applying the Genetic Algorithm (GA) to compare with the performance of the proposed method. The suggested fault detection model’s performance was evaluated by calculating the Receiver Operation Characteristic (ROC) curve, Specificity, Accuracy, Precision, Recall, and F1 score. The experimental results have proved the superiority of IWO for selecting the discriminant features, which has achieved more than 99.7% accuracy. The proposed hybrid model has successfully proved its robustness for diagnosing the faults under different load conditions.