Upon the higher requirement on high-performance structures of large-scale supporting structures of offshore wind turbines, the systematic analysis on the compressive-flexural behavior and ultimate bearing capacity of tapered concrete-filled double skin steel tubular (CFDST) members designed by over-ranging parameters was performed. Investigating the entire-process mechanism, e.g., the moment–deformation response, stress development, interaction stress, and subassembly contribution, was based on the finite element (FE) analysis, where the moment–deformation curve can be distinguished by four characteristic points, and the transverse local buckling of outer tube partly weakens distribution height of interface pressure in compression zone compared to that in tension zone. Influences of material strengths and geometric parameters were examined by the parametric study, e.g., increasing tapered angle (ψ) slightly reduces the bearing capacity; the higher axial compression ratio (n) contributes a noteworthy action on the post-peak behavior and carrying capacity, e.g., the bearing capacities at n = 0.9 and n = 0.5 reduce by 64.14% and 18.44% compared to capacity at n = 0.1, respectively; influence of Do/to ratio is more significant than Di/ti ratio. Subsequently, the modified cross-sectional stress integration (CSI) method was proposed to predict the moment–strain (M-ε) curves of tapered CFDST members; meanwhile, a confined concrete model with transverse confinement stress as an explicit parameter was modified, and influences of different confined concrete models on predicting M-ε curves were compared. Finally, design methods based on the modified CSI method and limit state method were proposed as a simplified calculation method to determine the correlative relationship of axial compressive strength and moment-resisting capacity (N-M curve).
Using high-strength steel (yield strength fy ≥ 460 MPa) in concrete-filled steel tubes is expected to provide a superior bearing capacity by achieving light weight and efficient construction, but the existing design limitation on diameter-to-thickness (D/t) ratios for concrete-filled high-strength steel tubular (CFHST) members inevitably obstructs its wide application. In this study, aiming at the application of circular CFHST members using Q690 steel (fy ≥ 690 MPa), a total of 15 CFHST beams were examined using a three-point loading test to investigate the failure mode, bearing capacity and plasticity evolution. Subsequently, finite element models (FEMs) were established to analyze the full-range curves, composite effect, failure mechanism and influences of key parameters including material strengths, D/t ratios, and shear-span ratios. A simplified calculation method for bearing capacity was finally proposed and verified. The results indicate that the full-range performance of tested CFHST members with out-of-code D/t ratios have ductile behavior, though they fail through the mode of steel fracture and concrete cracks in the tension zone as well as through local buckling in the compression zone; out-of-code CFHST members (e.g., D/t = 120) can perform reasonable composite behavior because of contact pressure larger than 2.5 MPa, where a thin-walled steel tube experiences an arch failure mechanism similar to core concrete at a trussed angle of 45°; the simplified bearing capacity model achieves a mean value of 0.97, and can be accepted as a primary tool to perform structural design and performance evaluation.
The thin-wall high-strength (HS) steel tube can provide strong confinement ability for core concrete due to its high yield strength, so it can achieve the purpose of confining concrete lateral deformation. In order to make full use of the mechanical properties of HS steel tube and concrete, it is necessary to study the axial compressive properties of the concrete-filled HS steel tube (CFHST) with a large diameter-to-thickness ratio (D/t). In this study, the axial compressive capacity of 15 CFHST columns with a large diameter-to-thickness ratio was tested. Then, a series of finite element (FE) models were developed to study the interaction mechanism between steel tube and concrete, the load–strain curves of typical specimens, and the effect of the key parameters. Finally, a new design proposal for CFHST compressive capacity is proposed and compared with EC4, GB50936-2014, and AIJ-97 prediction results. The results showed that the CFHST has good compressive capacity and can effectively confine the lateral deformation of core concrete; the contact pressure appears a stable stage because with a steel tube is difficult to effectively restrain the lateral deformation after steel tube yielding and partial failure of concrete; the existing design code is conservative in predicting the axial compression capacity of the CFHST with large D/t ratio.
The new-type stainless steel–concrete–carbon steel double-skin tubular (SCCDST) members, characterized by their exceptional corrosion resistance and mechanical bearing capacity, have promising applications in ocean engineering, particularly in deep-water engineering. The external hydraulic pressure and interfacial action of various materials intensify the complexity of composite performance of SCCDST members. This paper describes an analytical investigation on the concentric compressive performance of SCCDST members under external hydraulic pressure. The full-range mechanism, including load–displacement response, bearing capacity contribution, and contact pressures, was investigated through the finite element (FE) model that was validated by the failure mode, bearing capacity, and response of axial load versus strain. Subsequently, influences of key geometric–physical parameters were analyzed, e.g., diameter-to-thickness ratios (Do/to, Di/ti), material strengths (fyo, fyi, and fc), hollow ratios (χ), and water depths (H). Typical results indicate that: the initial active confinement action derived from the hydraulic pressure can enhance the interfacial contact pressure and axial compression capacity of SCCDST members due to the tri-axial compression state; the enhancement of confinement effect is mainly from the interfacial interaction between outer stainless steel tube and concrete infill; influence of water depth on bearing capacity cannot be ignored, e.g., the bearing capacity of an SCCDST member with larger hollow ratio (χ = 0.849) is not enhanced under a higher hydraulic pressure (H = 900 m) because of the cross-sectional buckling failure risk. Finally, a modified method considering the effect of water depth was proposed and verified for SCCDST members under hydraulic pressure.
A tapered concrete-filled double-skin steel tubular (TCFDST) structure has been used as the main framework in transmission towers, offshore facility platforms, and turbine towers owing to its excellent mechanical properties. In order to solve the difficulties of calculating the axial compressive capacity of TCFDST members due to the variations in cross-section, this paper applied heuristic optimization algorithms such as Genetic Algorithms (GAs), Particle Swarm Optimization (PSO), Simulated Annealing (SA), and Ant Colony Optimization (ACO) to enhance a Backpropagation Neural Network (BPNN) model. A predictive model incorporating both global and local optimization strategies for the axial compressive capacity of a TCFDST structure is proposed. A comprehensive axial database for TCFDST members, comprising 1327 sets of experimental and finite element analysis results, was established, with ten types of component dimensions and material parameters selected as input variables and compressive bearing capacity as the output variable. This study developed and assessed four BPNN models, each optimized by a different heuristic algorithm, against various machine learning algorithms and standards. The heuristic-algorithm-optimized BPNN models demonstrated superior accuracy in predicting the axial compressive capacity of TCFDST members. Through parametric analysis, this study identified the relationship between the model’s bearing capacity predictions and each input parameter, confirming the model’s broad applicability. The optimized BPNN model, refined with heuristic algorithms, provides a significant reference for addressing the computational challenges associated with the load-bearing capacity of TCFDST structures and facilitating their application.