Xin Jiang

Prof. Dr. Xin Jiang

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 July 2021
Verified
Conference Paper
Open access
SYSheng Yue
Sheng Yue
JRJu Ren
Ju Ren
XJXin Jiang
Xin Jiang
SLSen Lin
Sen Lin
JZJunshan Zhang
Junshan Zhang
In order to meet the requirements for performance, safety, and latency in many IoT applications, intelligent decisions must be made right here right now at the network edge. However, the constrained resources and limited local data amount pose significant challenges to the development of edge AI. To overcome these challenges, we explore continual edge learning capable of leveraging the knowledge transfer from previous tasks. Aiming to achieve fast and continual edge learning, we propose a platform-aided federated meta-learning architecture where edge nodes collaboratively learn a meta-model, aided by the knowledge transfer from prior tasks. The edge learning problem is cast as a regularized optimization problem, where the valuable knowledge learned from previous tasks is extracted as regularization. Then, we devise an ADMM based federated meta-learning algorithm, namely ADMM-FedMeta, where ADMM offers a natural mechanism to decompose the original problem into many subproblems which can be solved in parallel across edge nodes and the platform. Further, a variant of inexact-ADMM method is employed where the subproblems are 'solved' via linear approximation as well as Hessian estimation to reduce the computational cost per round to O(n). We provide a comprehensive analysis of ADMM-FedMeta, in terms of the convergence properties, the rapid adaptation performance, and the forgetting effect of prior knowledge transfer, for the general non-convex case. Extensive experimental studies demonstrate the effectiveness and efficiency of ADMM-FedMeta, and showcase that it substantially outperforms the existing baselines.

5 April 2020 in Environmental Science and Pollution Research
Verified
Journal Article
Closed access
PDF file
XCXiaoyue Chen
Xiaoyue Chen
ZXZhonghui Xu
Zhonghui Xu
ZYZhengzhen Yao
Zhengzhen Yao
QSQin Shuai
Qin Shuai
ZJZao Jiang
Zao Jiang
HLHan Li
Han Li

30 July 2023 in Buildings
Verified
Journal Article
Open access
PDF file
XJXin Jiang
Xin Jiang
HCHaoxuan Chen
Haoxuan Chen
YZYongjun Zhou
Yongjun Zhou
LMLin Ma
Lin Ma
JDJianqun Du
Jianqun Du
YLYunli Li
Yunli Li
Despite the potential advantages of 18 mm strands, the limited research on the behavior of girders with larger-diameter strands hinders the application in bridges. Transfer length and prestress losses are two important indicators. In this research, a 32.6 m long prestressed concrete box girder with 18 mm straight strands and 15 mm harped strands was produced, and the transfer length and the prestress losses were studied. The transfer length was calculated based on the existing equations in codes and previous research. Three beam specimens were fabricated, and strain gauges were pasted on the concrete surface to measure the transfer length of 18 mm strands. It indicated that the average measured transfer length was 700 mm. This value was smaller than the transfer lengths predicted by AASHTO LRFD 2017 and ACI 318-19, while Mitchell’s equation offered the closest prediction to the average measured transfer length. Additionally, the prestress losses at different stages were evaluated. A one-end stressing test was conducted to analyze the effect of strand harping on the loss of tensile force. In comparison with the actual measured loss based on the concrete strain and the longitudinal shortening, the instantaneous prestress loss calculated using the AASTHO LRFD 2017 alternative equation was appropriate. The time-dependent prestress losses due to shrinkage, creep, and relaxation were predicted using two different methods addressed in AASHTO LRFD 2017. The time-dependent predicted losses of 69.2 MPa at 28 d using the refined method were 37% higher than the measured losses 47.4 MPa at 28 d, indicating an overestimation of AASHTO LRFD 2017. The accumulation of the total losses over time revealed that the prestress losses developed in the first two months occupied the majority of the total losses in the long term. The research may provide guidelines for the design of a pretensioned concrete box girder with 18 mm strands.

28 June 2022 in Buildings
Verified
Journal Article
Open access
PDF file
XJXin Jiang
Xin Jiang
XBXinlin Ban
Xinlin Ban
LMLin Ma
Lin Ma
YSYonghua Su
Yonghua Su
Qi CaoQi Cao
Qi Cao
JGJichao Guo
Jichao Guo
Despite the attractive merits of high-capacity strands, the application in bridge girders is limited due to concerns, including concrete cracking, excessive stress, and cambers. An efficient and defect-free production is the first step to wide application. The objective of this research was to alleviate the production concerns of prestressed concrete bridge girders using high-capacity strands. A gigantic prestressed concrete box girder using 18-mm strands was produced; its entire fabrication process (from strand stressing to detension) was introduced. Sixteen temperature gauges were embedded in the girder to monitor the hydration of the large volume of concrete and the adjacent environmental temperature. Moreover, displacement transducers were used to measure the camber at detension; load cells were installed to monitor the variations of the prestressing strand tensile forces during fabrication. Monitoring and analysis showed that the timing of the detension is determined by the hydration of the concrete, the compressive strength of the concrete, and its modulus of elasticity or age. Since the tensile forces in strands are affected by the concrete’s internal temperature, the detension is conducted after the concrete temperature falls back (close to its initial value); otherwise, unfavorable and considerable prestress losses are caused. Finally, a 4-d detension was suggested since the hydration was not a concern at the time; the predicted prestress loss and camber were acceptable and the concrete material properties at 4 d satisfied the requirements.

17 March 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
WYWang Yelu
Wang Yelu
YZYongjun Zhou
Yongjun Zhou
XJXin Jiang
Xin Jiang
YZYu Zhao
Yu Zhao
HZHuantao Zhang
Huantao Zhang
The deflection dynamic load allowance (DLA) of stiff bridges with high piers requires sub-millimeter accuracy. New technologies such as the vision-based optical method and GNSS are not yet recognized for use in DLA measurements due to their smaller SNR. Presently, the scaffolding method is widely utilized for dynamic deflection measurements in dynamic load tests owing to the reliability of employing rigid contact. When scaffolding is not available, engineers have to resort to a suspension hammer system. However, the mass eccentricity of the hammer, stretched-wire length, and wind will decrease the measurement accuracy. To overcome these drawbacks of the suspension hammer method (SHM), a preloaded spring method (PSM) and the related stretched-wire-spring system (SWSS) are proposed in this paper. The dynamic deflection of the coupled vehicle-bridge-SWSS was obtained by vehicle-bridge interaction (VBI) analysis. The sensitivity parameters of the PSM were analyzed and optimized to minimize the measurement error. Indoor experiments and field dynamic load tests were conducted to validate the feasibility and accuracy of the PSM. Additionally, the differences in dynamic deflection measurements between the PSM and SHM in windy environments were compared. The results show that, in a windless environment, the DLAs of the PSM are affected by the spring stiffness, stretched-wire length, and stretched-wire section stiffness, independently of the preload force. When the wind speed is less than or equal to 8 m/s and the pier height is less than 30 m, the maximum deflection measurement error of the PSM is −2.53%, while that of the SHM is −15.87%. Due to its low cost and high accuracy, the proposed method has broad application prospects in the dynamic deflection measurement of stiff bridges with high piers.

8 September 2022
Verified
Book Chapter
Closed access
PDF file
XJXin Jiang
Xin Jiang
ZZZhouyu Zhang
Zhouyu Zhang
PWPeng Wang
Peng Wang
XBXinlin Ban
Xinlin Ban
MHMin Huang
Min Huang
JGJichao Guo
Jichao Guo