The initial experimental results of asymmetric mode competition in an X -band dual-mode relativistic backward wave oscillator (RBWO) operating at the low magnetic field are presented. In the experiment, the use of receiving antennas with different polarization directions allows direct determination of asymmetric mode, and the asymmetric mode with a frequency of 10.27 GHz is excited, which is in good agreement with the particle-in-cell (PIC) simulation results. Judging from that, the competition mode is asymmetric EH $_{\text{21}}$ mode. The asymmetric mode competition mechanism in the device is investigated theoretically. It is shown that the drift length plays a key role in the suppression and excitation of the asymmetric mode, validated by the experiment and the PIC simulation.
1 September 2022 in IEEE Transactions on Electron Devices
This article introduced a multipactor threshold criterion based on collision and emission currents, and the simulation results were compared using a traditional method. The impact of macroparticle weight on multipactor saturation was studied using electromagnetic particle-in-cell (EM-PIC) simulations of CST Particle Studio. It was found that the simulation results converged when the macroparticle weight was less than 106. A model calculating accumulated charge on the dielectric surface was proposed and validated against theoretical calculations. The dynamic evolution of multipactor in dielectric-loaded parallel-plate waveguide was analyzed, and predictions were validated against results from the existing model. Finally, the effect of surface charge fields and space charge effect on the multipactor mechanism was studied. The results showed that the multipactor could be suppressed when the ratio of the number of accumulated electrons on the dielectric surface to the saturation electron population was greater than 3.96.
The aim of this paper is to establish a numerical simulation model for the multipactor effect in a partially dielectric-loaded parallel-plate waveguide, with a focus on the investigation of multipactor saturation mechanisms for different dielectric materials with different secondary emission yield (SEY) properties. An electrostatic method involving the radio-frequency fields, space charge fields, and the dynamics of charge accumulation on the dielectric surface and solutions for electrostatic fields are proposed. The evolution of the electron number, accumulated charge, and secondary electron multiplication rate for different input voltages and SEY properties of the dielectric materials are studied using numerical calculations. The results show that two physical multipactor phenomena occur in a dielectric-loaded parallel-plate waveguide: a self-sustaining phenomenon, which means that the electron population reaches a saturation level, and a self-extinguishing phenomenon. The latter can be divided into two cases: in one, the number of electrons undergoes a process of multiplication, saturation, and reduction, and in the other, the number of electrons disappears after their population reaches a maximum. Furthermore, a multipactor susceptibility diagram for SEY curves of different dielectric materials is constructed. The results show that the multipactor effect is suppressed when the maximum of the SEY curve is less than 1.3.
12 December 2022 in IEEE Transactions on Electron Devices
This article presents a study of the multipactor effect in a double-sided dielectric-loaded parallel-plate waveguide. To this end, a 1-D electrostatic particle-in-cell model is established, which considers the radio frequency electric fields, space charge fields, and surface charge fields generated by the accumulated charge on the dielectric surface. The dynamic evolution of multipactor breakdown for different operating voltages and dielectric materials with different secondary electron yield (SEY) properties is investigated by numerical calculation. The results obtained show that multipactor does occur self-extinguishing phenomenon due to the presence of the surface charge fields under certain circumstances in the double-sided dielectric-loaded parallel-plate waveguide. Moreover, a comparative study of multipactor between metal, single-sided, and double-sided dielectric-loaded parallel-plate waveguides is carried out. The simulation results show that the self-extinguishing time of the multipactor in the double-sided dielectric-loaded model is less than that in the single-sided dielectric-loaded model. Finally, a multipactor susceptibility diagram for the SEY curve of different bottom dielectric materials in the parallel-plate waveguide is constructed. The results show that the single-sided dielectric-loaded microwave components are more beneficial to suppress the multipactor effect. The results reported in this study can be used to guide the design of space high-power microwave components.
Multipactor occurrence essentially depends on the secondary emission property of the surface material, which is, thus, the requisite input for multipactor threshold prediction using the numerical and theoretical approaches. However, secondary emission yield (SEY) deviation in experimental measurements inevitably leads to uncertainty error in multipactor threshold prediction. Therefore, this paper presents a thorough quantitative analysis of multipactor threshold sensitivity to SEY including the effect of the device geometry, the multipactor mode, and the material type. Based on the statistical modeling, multipactor threshold voltages with respect to the SEY variation in critical SEY regions are calculated for both the parallel plates and coaxial lines with different multipactor orders and typical materials. Furthermore, the distribution of electron impact energy is also obtained to elucidate the underlying mechanism for the relevant sensitivity discrepancy. The result reveals that multipactor threshold is generally most sensitive to the energy region below the first crossover energy (E1), and this is changed to higher energies below the corresponding energy to the SEY maximum (Em) with a change in the device geometry, multipactor mode, or coating material. It is also found that the magnitude relation of the threshold sensitivity between different regions is radically determined with the distribution of electron impact energy, and the SEY variation close to Em merely affects the threshold result with a high multipactor order. This research provides useful reference for properly determining the threshold margin from the measurement error of SEY, thus promoting the performance optimization with multipactor prevention in the practical application of microwave devices.
To accelerate the design of a high-power microwave device, a deep learning assisted multi-objective optimization method is used to optimize a Ka-band relativistic backward-wave oscillator (RBWO) operating with a low magnetic field. Particle-in-cell simulation results show that the optimized RBWO with a tooth-shaped slow wave structure (SWS) can generate microwave pulses with an output power of 1.24 GW and an operating frequency of 26.8 GHz under a diode voltage of 623.3 kV, and the diode current is 6.56 kA at a guiding magnetic field of 0.8 T. Compared with the original RBWO, the output power of the optimized RBWO has been increased by 201.2%, and the beam-to-microwave conversion efficiency has increased from 10.0% to 30.3%. The detailed analysis reveals that in an overmoded RBWO with low guiding magnetic fields, the introduction of a tooth-shaped SWS is beneficial to mode competition, improves output power, and decreases microwave starting time.