Seong Daehee

Dr. Seong Daehee

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 October 2025 in Metals
Verified
Journal Article
Open access
PDF file
JPJungGoo Park
JungGoo Park
GAGyubaek AN
Gyubaek AN
JPJeongung Park
Jeongung Park
Seong DaeheeSeong Daehee
Seong Daehee
WJWonJun Jo
WonJun Jo
This study investigates the effect of hydrogen embrittlement on the fracture toughness of 9% Ni steel and STS 316L stainless steel under cryogenic conditions ranging from −80 °C to −253 °C. Hydrogen charging was performed using electrochemical methods, and hydrogen uptake was quantitatively analyzed using thermal desorption spectroscopy (TDS). Fracture toughness was evaluated using crack tip opening displacement (CTOD) testing per ISO 12135, both without hydrogen (WO-H) and with hydrogen (W-H). The results showed a gradual decrease in CTOD values with decreasing temperature in both steels under hydrogen-free conditions, with ductile fracture maintained even at −253 °C. In contrast, hydrogen-charged specimens exhibited significant toughness degradation at intermediate subzero temperatures (−80 °C to −130 °C), particularly in 9% Ni steel due to its BCC crystal structure. However, at −160 °C and below, the effect of hydrogen embrittlement was suppressed mainly owing to the reduced hydrogen diffusivity. Scanning electron microscopy (SEM) analysis confirmed the transition from ductile to brittle fracture with decreasing temperature and hydrogen influences. At −253 °C, fully brittle fracture surfaces were observed in all specimens, confirming that at ultra-low temperatures, fracture behavior is dominated by temperature effects rather than hydrogen. These findings identify a practical temperature limit (approximately −160 °C) below which hydrogen embrittlement becomes negligible, providing critical insights for the design and application of structural materials in hydrogen cryogenic environments.

22 December 2022 in Metals
Verified
Journal Article
Open access
PDF file
Seong DaeheeSeong Daehee
Seong Daehee
GAGyubaek AN
Gyubaek AN
JPJeongung Park
Jeongung Park
WWWanchuck Woo
Wanchuck Woo
Using high-strength steel for offshore structures with a yield stress of 500 MPa, this study evaluated the distribution characteristics of welding residual stress in the thickness direction under the influence of constrained conditions during welding using cutting, neutron diffraction, and contour methods. Welding residual stress inevitably occurs during welding and impacts fracture stability in structures. As high-strength steel better reflects the effects of phase transformation, the behavior of welding residual stress is known to differ from that of general steel. This study fabricated fully constrained and unconstrained specimens and evaluated them under identical conditions to evaluate welding residual stress according to the influence of constraints on high-strength steel welds. The results indicated that the maximum tensile residual stress of the fully constrained specimen occurred in the first layer of the weld joint, while the maximum tensile residual stress of the fully unconstrained specimen occurred in the last layer of the weld joint. Additionally, the welding residual stress of the fully constrained specimen was larger. Although some errors occurred in the residual stress values in the thickness direction depending on the measurement method, both methods applied in this study exhibited nearly identical distributions. Meanwhile, a maximum angular deformation of about 6° occurred in the fully unconstrained specimen, and we considered that the residual stress decreased owing to the occurrence of angular deformation. The maximum welding residual stress is generally the degree of yield stress. When residual stress greater than the yield stress occurs, it changes to the plastic range and appears in the form of angular, longitudinal, and lateral deformation. Under the fully unconstrained condition, reduced residual stress is considered to appear in the form of angular deformation. The welding tensile residual stress decreased to around 42% in the unconstrained specimen compared to the constrained specimen, and at that time, angular deformation of approximately 6° occurred. Therefore, it is estimated that an angular distortion of about 2.4° occurs as the stress of 100 MPa decreases.

31 August 2024 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
Seong DaeheeSeong Daehee
Seong Daehee
WJWonJun Jo
WonJun Jo
JRJisun Roh
Jisun Roh
JPJungGoo Park
JungGoo Park
JPJeongung Park
Jeongung Park
GAGyubaek AN
Gyubaek AN
In this study, fracture toughness with the base metal of 9% Ni steel, a cryogenic steel, was evaluated under conditions without hydrogen charging (WO-H) and with hydrogen charging (W-H). Hydrogen charging was performed using an electrochemical cathodic charging method in a electrolyte of 3% NaCl + 0.3% NH4SCN at 19℃ with a current density of 50 A/m². Fracture toughness was assessed at -80℃, -100℃, -130℃, and -160℃ using CTOD (Crack Tip Opening Displacement) tests. The results for WO-H indicated a decrease in fracture toughness values with decreasing temperature, while the results for W-H showed an increase in fracture toughness values as the temperature decreased. In addition, the fracture surfaces and fracture toughness of WO-H and W-H became increasingly similar as the temperature decreased, as observed through scanning electron microscopy (SEM). At -80℃, there was a significant difference in fracture toughness between the WO-H and W-H conditions. WO-H was influenced only by the low temperature, whereas W-H was affected by both low temperature and hydrogen, showing combined effects that led to a decrease in fracture toughness due to hydrogen embrittlement. However, at -160℃, the fracture toughness values for both WO-H and W-H conditions were nearly identical. This suggests that the temperature effect on fracture toughness reduction is greater than hydrogen embrittlement at very low temperatures.

28 February 2022 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
Seong DaeheeSeong Daehee
Seong Daehee
GAGyubaek AN
Gyubaek AN
JPJong-Ung Park
Jong-Ung Park
The characteristics of welding residual stress distribution in high-strength steel for offshore structures were evaluated based on the effect of constraint. It is well known that high-strength steel exhibits a high welding residual stress, and the welding residual stress is a significant factor for evaluating unstable fractures. Test specimens were manufactured by applying different constraint conditions. The constrainted and unconstrainted specimens were welded with the same welding consumables and conditions to evaluate the welding residual stress distribution characteristics. The cutting method was applied to assess the welding residual stresses of both specimens. The results showed that the welding residual stress at the heat-affected zone of the unconstrainted specimen decreased compared with that of the constrainted specimen. However, angular distortion occurred in the unconstrainted specimen instead of reduced welding residual stress.

29 December 2023 in Metals
Verified
Journal Article
Open access
PDF file
GAGyubaek AN
Gyubaek AN
JPJeongung Park
Jeongung Park
Seong DaeheeSeong Daehee
Seong Daehee
JSJunseok Seo
Junseok Seo
As the shipbuilding industry has emerged from an extended recession, orders for high-value-added ships, such as LNG and ultra-large container ships, are increasing. For ultra-large container ships, high-strength, thick materials are applied. Because the possibility of brittle fracture increases owing to the application of thick steel plates, the related regulations of the International Association of Classification Societies have been strengthened to prevent brittle fracture. To secure brittle fracture stability, it is necessary to secure crack arrest toughness (Kca) through large ESSO experiments or to secure a crack arrest temperature (CAT) value. Because large-scale experiments require considerable costs and efforts, efforts have increased to examine brittle fracture stability through small-scale tests. In the present study, a technology was developed to predict CAT with small specimens. The CAT prediction formula developed with small specimens makes it possible to accurately predict CAT using data obtained through large-scale experiments.

17 July 2026 in Engineering Fracture Mechanics
Verified
Journal Article
Closed access
WJWonjun Jo
Wonjun Jo
JLJiseung Lee
Jiseung Lee
Seong DaeheeSeong Daehee
Seong Daehee
GAGyubaek An
Gyubaek An