The use of biogas has currently two disadvantages. First, processing biogas to natural gas quality for feeding into the natural gas grid is a rather energy-consuming process. Second, the conversion into electricity directly in biogas plants produces waste heat, which largely cannot be used. Therefore, a feed-in of the desulfurized and dry biogas to local biogas grids would be preferable. Thus, the biogas could be used directly at the end consumer for heat and power production. As biogas varies in its methane (CH4) and carbon dioxide (CO2) content, respectively, this paper studies the influence of different biogas mixtures compared to natural gas on the combustion in a flameless oxidation (FLOX®)-based six nozzle combustor. The single staged combustor is suitable for use in a micro gas turbine (MGT) based combined heat and power (CHP) system with an electrical power output of 3 kW. The combustor is studied in an optically accessible atmospheric test rig, as well as integrated into the MGT system. This paper focuses on the influence of the admixture of CO2 to natural gas on the NOx and CO emissions. Furthermore, at atmospheric conditions, the shape and location of the heat release zone are investigated using OH* chemiluminescence (OH* CL). The combustor could be stably operated in the MGT within the complete stationary operating range with all fuel mixtures.
20 December 2023 in Journal of Engineering for Gas Turbines and Power
The effect of superheated liquid fuel injection on the performance and emissions of a single nozzle combustor was investigated. Combustion of the lean premixed flames was achieved using a combination of jet and swirl as a stabilization method. In a nonreactive setup, the optimum transition temperature of Jet A-1 fuel from liquid to superheated vaporized state was analyzed. In a subsequent reactive setup, a series of tests were conducted with the liquid fuel at low and elevated temperatures. The experiments were conducted at ambient pressure and various air and fuel preheat temperatures, axial swirlers, thermal powers, adiabatic flame temperatures, and flame tube diameters. Concentrations of nitric oxide (NOx) and carbon monoxide (CO) in the flue gas were measured. The operating conditions were systematically selected according to the design of experiments (DOE) method. The results showed that the adiabatic flame temperature caused the most significant change in combustion emissions and the position and shape of the reaction zone, while the superheated fuel injection had only a minor effect because the liquid fuel droplets were largely vaporized before entering the reaction zone through the integration of a swirler and a prefilmer. The use of the axial swirler and prefilmer allowed the combustor to operate in both spray and fully vaporized fuel conditions. As a result, very low emission concentrations of NOx (≈5 ppm) and CO (≈6 ppm) were achieved. The median flame length and height above the burner of the characterized flames showed competitive values of 32 mm and 50 mm, respectively. Lean blowout limits of less than 1500 K were achieved. Two different flame modes were observed during the experiments. By increasing the bulk velocity of the combustor, its hysteresis was resolved, resulting in stable and reliable flames with a wide low-NOx operating range.
6 September 2024 in Journal of Engineering for Gas Turbines and Power
A newly developed gas turbine combustor system based on the swirl-assisted jet-stabilized concept using Jet A-1 and natural gas as reference fuel is tested under wet conditions to evaluate its combustion characteristics in the presence of steam. The effect of steam injection into the gas turbine combustor under both spray and superheated liquid fuel injection conditions is studied experimentally on an atmospheric test rig. To evaluate the effect of steam injection on combustion performance, the water-to-gas ratio (WGR) is varied from 0 to 32%. With increasing WGR = 0 to 16% and at stoichiometric condition, NOx reductions of -82% to -100% were observed during Jet A-1 and natural gas combustion, respectively. It is shown that the reduction of the combustion zone temperature due to the steam acting as a heat sink is the main cause of the NOx decrease. The operating range of the burner remained fairly constant for Jet A-1 until WGR = 20%, while it decreased significantly with increasing WGR for natural gas combustion. While the effect of the WGR on CO was modest, the greatest effect of the WGR was on the heat release zone intensity at a constant air to fuel ratio. In reducing the NOx levels of Jet A-1 and natural gas combustion, both thermal and chemical effects of steam injection were observed. However, steam acting as a heat sink and lowering the flame temperature, thereby reducing the thermal NO formation rate, was the dominant factor in NOx reduction.
Renewable energy sources such as wind turbines and photovoltaics are the key to an environmentally friendly energy supply. However, their volatile power output is challenging in regard to supply security. Therefore, flexible energy systems with storage capabilities are crucial for the expansion of renewable energy sources since they allow storing off-demand produced power and reconverting and supplying it on-demand. For this purpose, a novel power plant concept is presented where high-temperature energy storage (HTES) is integrated between the recuperator and the combustor of a conventional micro gas turbine (MGT). It is used to store renewable energy in times of oversupply, which is later used to reduce fuel demand during MGT operation. Hereby, pollutant emissions are reduced significantly, while the power grid is stabilized. This paper presents a numerical process simulation study, aiming to examine the influence of different storage temperatures and load profiles of HTES on the MGT performance (e.g., fuel consumption, efficiency). Furthermore, relevant operating points and their process parameters such as pressures, temperatures, and mass-flow rates are derived. As operation conditions for the combustor are strongly influenced by the HTES, the paper contains a detailed theoretical analysis of the impact on combustor operability and includes an experimental investigation of the first combustor design adapted for the compound and tested under higher inlet temperatures conditions.
In the course of the German energy revolution, the proportion of wind and solar power has increased significantly over the last decade. Since both are volatile energy sources, an alternative renewable solution is needed to compensate for fluctuations in energy and to provide demand responsive power. A promising approach is the use of biogas via the fermentation process which
6 September 2024 in Journal of Engineering for Gas Turbines and Power
A major challenge for gas turbine combustor technology is the emission of NOx and CO. Achieving an optimal premixed, prevaporized, dry low-NOx condition is a critical issue for liquid fuel combustors. To accomplish this, the relationship between combustor configuration and the performance of a newly developed swirl-assisted jet-stabilized combustor is investigated in an atmospheric combustion facility. The influence of each combustor component on combustion performance and fuel evaporation behavior is evaluated independently using optical combustion diagnostics. In addition, the effect of air and liquid fuel temperature on fuel evaporation is characterized. Jet A-1 was injected coaxially into the air stream under both spray and superheated conditions. During the experiments, five critical combustor components were varied to understand their individual effect on fuel vaporization and thus combustion performance. Exhaust gas emissions of NOx, CO as well as OH* chemiluminescence images were used to evaluate combustor performance. Mie scattering technique was used to analyze the degree of liquid fuel evaporation for different test cases. It was found that the combustion performance indicators CO, height above burner and flame length were well controlled by the degree of fuel evaporation, while NOx emissions showed little change with different combustor configurations. While the main factor influencing the level of NOx emissions was the adiabatic flame temperature, the quality of fuel evaporation played a minor role. It was found that the operating range of the combustor and the geometric shape of the flame are significantly influenced by the components of the combustor.