This paper proposes a dual-core quad-mode millimeter-wave (mm-wave) voltage-controlled oscillator (VCO) using a compact multi-mode LC network with a modeindependent switched transformer technique. On top of the dualmode main LC tank, the mode-independent switched transformer technique introduces two additional oscillation modes, further extending the frequency tuning range with a small chip area overhead, while the mode-independent feature reduces the cost of switch off-capacitance compared with the conventional switched transformers. Implemented in 65nm CMOS process, the proposed VCO achieves a measured octave frequency tuning range from 20.65 to 40.55 GHz. The measured best phase noise is -131.04 dBc/Hz at 10 MHz offset from 20.65 GHz. The measured best figure-of-merit (FoM) is 187.25 dBc/Hz at 10 MHz offset from 26.66 GHz, corresponding to a figure-of-merit of tuning range and area (FoMTA) of 216.72 dBc/Hz thanks to the proposed compact multi-mode LC network and the mode-independent switched transformer technique. The VCO consumes 9.75-to-18.85 mW from a 0.65 V supply voltage. The core area is 0.048 mm2.
This paper presents a wideband dB-linear variable-gain amplifier (VGA) with a DC-offset cancellation network in a 90-nm CMOS technology for high-speed applications. The VGA consists of a four-stage Cherry-Hooper amplifier, which is based on a feedback resistor and negative Miller capacitance to obtain wide bandwidth without inductors in the main circuit. A unique method for this structure to generate pseudo-exponential function is analyzed in detail. Therefore, an accurate dB-linear characteristic is realized in this VGA without any exponential generator circuits. The linear control voltage is applied directly to the gate of the transistor and this simple control method exhibits good robustness to process and temperature variation. Measurement results show that the voltage gain varies from −28 dB to 27 dB continuously with more than 4.3 GHz bandwidth and a dB-linear range of 32 dB with less than ±0.6 dB gain error. Without the output buffer, it consumes 8.5 mW from a 1.2V supply and occupies a small die area of only 0.04 mm 2 .
This paper describes an N-path sub-GHz ultra-low power receiver exploiting an N-path notch filter topology in 90nm CMOS process. The receiver achieves the flexibility in the operating frequency due to an adjustable internal impedance matching network with an N-path notch filter. The receiver consists of two current-reused topologies, which greatly simplifies the structure and achieves ultra-low power consumption. Specifically, the receiver incorporates: 1) an amplifier with an N-path notch filter, which acts as the first stage of the receiver to provide an input impedance of 50 Ω without an inductor. This input matching network is frequency flexible and adjustable to suit different frequencies of the input signal. Meanwhile, the N-path notch filter can suppress out-of-band interference to cope with limited frequency bands. 2) N-path passive mixers are reused for simultaneous filtering and down-conversion. 3) Amplifiers are frequency-division multiplexed to amplify both RF and baseband signals simultaneously. Finally, the receiver is fabricated in 90 nm CMOS and operates at 0.6 V supply voltage with a power consumption of 780 μW. The receiver achieves a conversion gain of 41.2 ± 3.2 dB, a noise figure of 5.7 ± 0.3 dB and an OB-IIP3 of 14.6 ± 0.5 dBm. The chip area of the implemented receiver is 0.08 μm 2 .
In this article, we present an ultra-wideband, fully-differential quadrature signal generation network for 5G applications. The ultra-wideband network is composed of a passive balun and cascaded transformer-based quadrature hybrid. Passive balun converts a single-ended signal to differential with minimum insertion loss, and transformer-based quadrature hybrids are cascaded to suppress I/Q imbalance over an ultra-wide bandwidth. The coupling coefficient of the transformer-based quadrature hybrid is enhanced by adopting vertically stacked multiturn transformer topology to extend operation bandwidth and reduce passive loss and chip area. A novel layout and signal routings are proposed to reduce passive loss, undesired magnetic coupling and I/Q imbalance, making meander lines for phase matching unnecessary. The proposed ultra-wideband quadrature signal generation network is designed in GlobalFoundries 45 nm CMOS SOI process with a core area of 845 μm 495 μm. The output I/Q magnitude mismatch is less than 0.5 dB from 16 to 60 GHz, and phase mismatch is less than 2° from 16.5 to 54.7 GHz. The input return loss is lower than −10 dB from 22 to 45 GHz, and signal loss varies from 5.74 to 7.4 dB (including 1:2 power splitting and loss from passive balun). The effective image rejection ratio (IRR) is calculated based on I/Q mismatch and is higher than 40 dB from 21.5 to 53.5 GHz.
This paper presents a multi-band ultra-low power (ULP) receiver with N-Path Switched-Capacitor (NPSC) networks in 90 nm CMOS process. The NPSC is integrated into the feedback loop of the low noise amplifier (LNA) to flexibly provide narrowband input matching at multiple sub-GHz Industrial, Scientific, and Medical (ISM) bands by adjusting the switching frequency. Moreover, the LNA with an NPSC network is utilized to suppress the out-of-band signal at the input and output of the LNA, simultaneously. In order to achieve an ultra-low power consumption, a sub-threshold LNA and four passive NPSC mixers are implemented in this receiver. The ULP receiver achieves a measured gain of dB in ISM bands (430/860/915/960 MHz). The measured noise figure and out-of-band IIP3 are dB and dBm, respectively. The ULP receiver chip consumes 320 W at 0.4 V power supply and occupies a chip area of 0.31 mm.
This paper presents a multi-band low-noise amplifier (LNA) in the 45-nm CMOS silicon-on-insulator (SOI) process. The LNA consists of three stages, with the differential cascode amplifier as the core structure. The first stage is mainly responsible for input matching to ensure favourable noise characteristics and bandwidth, while the subsequent stages increase the gain. Moreover, the LNA utilizes baluns for input/output and interstage impedance matching. Switch capacitances are added to switch the three operating bands of the LNA, which cover 17–38 GHz overall. Measurement results show that the proposed LNA achieves a gain (S21) of 23.0 dB and a noise figure (NF) of 4.0 dB.