The dynamic response of a prestressed concrete box girder bridge under the impact of an over-height vehicle is studied using the numerical simulation method. The finite element analysis software LS-DYNA is used to simulate the collision between the bridge superstructure and an over-height truck. Further, a parametric analysis is carried out to investigate the influence of six factors, i.e., girder configuration, vehicle speed, vehicle mass, impact angle, concrete strength and strand prestress, on both local damage and overall performance of the bridge. The numerical analysis results show that the girder configuration, vehicle speed, vehicle mass and impact angle have obvious effects on both local damage and the overall behavior of the PC box girder bridge. Whereas, the concrete strength and strand prestress only have a certain effect on the local damage at the impact area with very limited influence on the overall behavior of the bridge. In addition, based on the results obtained from the numerical simulation and parametric analysis, a formula for predicting the peak and average impact force of the prestressed concrete box girder bridge under the over-height vehicle impact is developed. The proposed impact force formula comprehensively accounts for the influence of the vehicle speed, vehicle mass and impact angle and can accurately predict the impact force generated under different working conditions, which confirms the promising prospect of the proposed formula in practical applications.
U-shaped girder has been extensively used for its excellent adaptability in the urban railway transit system. As an open thin-walled structure, significant difference of working mechanism exists between U-shaped girder and conventional section girder (e.g., T section or box section). The thin-walled web plays significant role in the flexural performance of U type girder particularly. Moreover, severe collision may occur between the moving train and the girder, and subsequently results in the decrease of the structural bearing capacity. In this paper, a full-scale test was carried out to examine the ultimate bearing capacity and the failure mechanism of the U-shaped girder, and a refined numerical model was developed to simulate the damage evolution and the failure process. It was shown that the flexural failure occurred on the U-shaped girder under vertical loads. In addition, the ultimate bearing capacity of the structure under different web damage conditions (e.g., web damaged region or damaged range) was studied by applying the displacement based lateral load on the flange of the U-shaped girder to simulate the damage caused by accidental train collision. The numerical results have shown that the damaged web greatly affects the ultimate bearing capacity of U-shaped girder, more severe bearing capacity descending occurs around the middle span rather than the beam ends. The damaged range (length) of the web has less influence on the falling amplitude of bearing capacity. It can be concluded that the major reason accounting for the bearing capacity decrease is that the original section is weakened by the web damage, and consequently results in the buckling of the damaged web and lead to the total failure of the structure. It is recommended that the lateral resistant design for the web should be taken into consideration to ensure the operation safety of the urban railway transportation.
A new fracture model is developed to predict the ductile fracture of structural steel under multiaxial stress states. First, the Lee–Mear void growth theory is used to establish the quantitative relationship between the stress triaxiality and material’s ductility. A stress triaxiality dependence function, which accounts for the material’s strain hardening, is derived from modifying the dilatation rate of a spherical void in a typical unit cell. Subsequently, the Tresca failure model is used in conjunction with the Swift hardening law to establish a Lode dependence of fracture strain. Then, the theoretical formula of the new fracture model is obtained by combining both stress triaxiality and Lode angle dependence functions. The proposed fracture model has a unique advantage: i.e., this model has only two material parameters. These two parameters can be easily calibrated through a simple standard coupon test, which significantly reduces the difficulty of model calibration work and facilitates its application in practical engineering. In order to verify the new fracture model, the test results of five types of Q460 steel specimens were used to calibrate the model parameters. The prediction accuracy of the new model is then checked by calculating the average error between the test results and the predicted fracture strain envelope. Finally, the new fracture model was applied in the numerical analysis of two types of steel connections. The validation of the proposed fracture model is verified by comparing the load–displacement curve and failure modes of the steel connections obtained from both test and numerical analysis.
Suspension bridges are the most common type of bridge used to cross the ocean. The cable clamps in suspension bridges clamp the main cables by bolt preload, but the elastic interaction of the bolts reduces the preload, which is detrimental to the force in suspension bridges. However, research on the factors influencing the elastic interaction of cable clamp bolts in suspension bridges is currently limited. This paper aims to explore the law of influence of external factors on the elastic interaction of bolts through a combined approach of theoretical analysis, full-scale experiment, and finite element simulation. The results indicate that the average preload loss was reduced by about 27% when the elastic modulus was increased by about 110%. The average preload loss was reduced by about 45% when the bolt center distance was increased by 75%. The number of bolts has a small effect on the elastic interaction, which can be ignored. When the preload of bolt installation was increased by 133%, the average preload loss was reduced by approximately 125%, which was almost a linear relationship. Tightening the bolt from the center bolt creates greater elastic interaction. The conclusions can provide suggestions for reducing the elastic interaction of bolts in the design and construction of suspension bridge cable clamps.
The pull-out method is a simple and effective method for detecting the preload of suspension bridge cable clamp bolts. However, research on the pull-out method is currently limited. The force principles governing the bolt during the pulling process are unclear, and the relationship between tension force and the desired preload remains uncertain. This paper aims to explore the force principles of bolts during the pull-out method detection process through a combined approach of theoretical analysis, full-scale test, and finite element simulation. The results indicate that the bolt preload increases during the pulling process. The preload detected by the pull-out method is not the initial preload of the bolt, but rather it exceeds the initial preload. The force relationships among various components are determined as follows: the preload subtracts the change value of the force exerted by the nut at the tension end, which equals the change value of tension force. Additionally, an analysis of the impact of the length of the bolt clamping section and the bolt area on the preload was conducted. Under the same bolt area, a shorter clamping section length corresponds to a greater increase in preload. With the same clamping section length, the increment of preload increases with the bolt area. These findings can serve as references for detecting and specifying the preload of the bolts.