Silicon-based photovoltaic technology is helpful in reducing the cost of power generation; however, it suffers from economic losses and environmental pollution caused by silicon cutting waste. Herein, a hydrothermal method accompanied by heat treatment is proposed to take full advantage of the photovoltaic silicon cutting waste and biomass excrementum bombycis to fabricate flake-like porous Si@C (FP-Si@C) composite anodes for lithium-ion batteries (LIBs). The resulting FP-Si@C composite with a meso-macroporous structure can buffer the severe volume changes and facilitate electrolyte penetration. Meanwhile, the slightly graphitic carbon with high electrical conductivity and mechanical strength tightly surrounds the Si nanoflakes, which not only contributes to the ion/electron transport but also maintains the electrode structural integrity during the repeated lithiation/delithiation process. Accordingly, the synergistic effect of the unique structure of FP-Si@C composite contributes to a high discharge specific capacity of 1322 mAh g−1 at 0.1 A g−1, superior cycle stability with a capacity retention of 70.8% after 100 cycles, and excellent rate performance with a reversible capacity of 406 mAh g−1 at 1.0 A g−1. This work provides an easy and cost-effective approach to achieving the high-value application of photovoltaic silicon cutting waste, as well as obtaining high-performance Si-based anodes for LIBs.
Silicon is considered to have significant potential for anode materials in lithium–ion batteries (LIBs) with a theoretical specific capacity of 4200 mAh g−1. However, the development of commercial applications is impacted by the volume shift that happens in silicon when charging and discharging. In this paper, a yolk–shell–structured Si@void@C anode material has been developed to address this problem. The silicon nanoparticle yolk material is obtained by recycling kerf loss (KL) Si waste from the process of slicing silicon block casts into wafers in the photovoltaic industry; the carbon shell is prepared by a hydrothermal method with glucose, and the sacrificial interlayer is Al2O3. The produced material is employed in the production of anodes, exhibiting a reversible capacity of 836 mAh g−1 at 0.1 A g−1 after 100 cycles, accompanied by a Coulomb efficiency of 71.4%. This study demonstrates an economical way of transforming KL Si waste into materials with an enhanced value for LIBs.
To break the inherent mirror symmetry and promote the atomization for the traditional jet–jet impingement, the present paper proposed an improvement by the impingement between two spinning jets and numerically verified the enhancement of liquid sheet breakup and atomization by jet spinning effects. First, an appropriate jet spin velocity was selected based on the deformation and flow instability for a single spinning jet. Then, the impingement between two non-spinning jets and spinning jets with different spin directions at either small or large jet injection Weber numbers were studied. The results verified that the identical spinning jet–jet impingement could promote the liquid sheet breakup and atomization for the small jet injection inertia, which is especially useful for the variable thrust engines at small mass flow rate conditions; and the jet spin motion plays insignificant roles because the liquid sheet breakup is dominated by the sufficient large jet injection inertia. In addition, too large jet spin angular velocity causes the premature Rayleigh–Taylor instability and reduces the effective jet–jet impingement mass. Finally, the enhancement of liquid sheet breakup and atomization is also applicative for the spinning jet–jet impingement of high-viscous liquids usually used in practical applications.
Silicon-based photovoltaic (PV) technology is helpful in reducing the cost of power generation, however, suffers from economic losses and environmental pollution caused by silicon scraps. Herein, a facile and low-cost method is proposed to take full advantage of the PV silicon scraps and biomass excrementum bombycis fabricating the flake-like porous Si@C (FP-Si@C) composite anodes for lithium-ion batteries (LIBs). The resulting FP-Si@C composite with meso-macropores structure can buffer the severe volume changes and facilitate the electrolyte penetration. Meanwhile, the slightly graphitic carbon with high electrical conductivity and mechanical strength tightly surrounds the Si nanoflakes that not only contributes to the ion/electron transport but also maintains the electrode structural integrity during the repeated lithiation/delithiation process. Accordingly, synergistic effect of the unique structure of FP-Si@C composite contributes a high discharge specific capacity of 1322 mAh g −1 at 0.1 A g −1 , superior cycle stability with capacity retention of 70.8% after 100 cycles, and excellent rate performance with a reversible capacity of 406 mAh g −1 at 1.0 A g −1 . This work provides an easy and cost-effective approach to achieve high value application of PV silicon scraps, as well as obtain high-performance Si-based anodes for LIBs.
We conducted molecular dynamics (MD) simulations to investigate the structural evolution of molten slag composed of wheat straw (WS) and Shenhua (SH) coal. The content of wheat straw in the slag was varied from 0 to 100 wt%. The MD results indicated a slight reduction in the sharpness of the radial-distribution-function curve of each ion–oxygen pair and a decrease in bonding strength with increasing WS content. WS introduced many metal ions to the ash system, increasing its overall activity. The number of bridging and non-bridging oxygen atoms changed upon straw addition, which affected the stability of the system. There were relatively few highly coordinated Si ions. The number of low-coordination Si was highest for a WS content of 30%, at which the density reached a minimum value. The degree of ash polymerization was analyzed by counting the number (Q) of tetrahedra with the number (n) of the bridging oxygen atoms. With increasing WS content, Q4 (tetrahedral Si) decreased, whereas Q3, Q2, Q1, and Q0 increased. Q4 reached a minimum value for a WS content of 30%, at which point the degree of ion aggregation was the weakest and the degree of disorder was the strongest.