Fiber materials as an asphalt mixture additive and stabilizer can effectively improve the performance index of asphalt pavement. In this study, lignin and carbon fiber were used as modifiers to study their effects on the road performance of asphalt mastic. Based on the frequency sweep, linear amplitude sweep (LAS) and multi-stress creep recovery (MSCR) experiments were conducted to test the high-temperature rutting and medium-temperature fatigue resistance of asphalt mastic with different fiber incorporation and low-temperature performance tests based on bending beam rheometer (BBR). The results indicate that adding fibers increased the stiffness of the asphalt mastic, and the modification effect of lignin fibers was better than that of carbon fibers. Meanwhile, the characteristic flow index of the asphalt mastic gradually increased with the increase in temperature, indicating that it gradually became a near-Newtonian fluid at higher temperatures. The addition of fibers also improved the high temperature rutting resistance of the asphalt mastic but did not have an advantageous effect on fatigue and low temperature cracking resistance. Additionally, the fitting results of the four-parameter Burgers model show that the use of fiber modification decreases the proportion of elasticity and viscous creep compliance but increases the delayed elasticity part.
This paper introduces a new phase-variable switch control for the parallel synchronized triple bias-flip (P-S3BF) interface circuit, towards the broadband and high-capability piezoelectric energy harvesting (PEH) systems. By using the phase-variable P-S3BF (PV-P-S3BF), both the electrically induced damping and electrically induced mass/stiffness can be tuned to a certain extent in operation, such that to simultaneously make the dual tasks of broadband and high-capability in PEH. The joint dynamics and harvested power of the PEH systems using the PV-P-S3BF circuits are thoroughly discussed based on the harmonic analysis and impedance modeling. The available range of PV-P-S3BF is rationally shown in the complex impedance plane. The experimental results obtained with a PCB-level prototyped circuit show agreement with the analytical results. The new PV-P-S3BF circuit opens a promising future towards the electrically in-situ tunable broadband and high-capability PEH systems.
Asphalt pavement presents diverse dynamic responses to vehicle loading in dry and saturated conditions, which can be systematically explored by numerical simulation. Building a numerical model based on the actual conditions of asphalt pavement is necessary, and relevant field tests should be subsequently conducted to monitor dynamic responses to calibrate and validate the numerical model. On the basis of strictly controlling the paths of vehicle wheels during field tests, this study numerically analyzed the dynamic responses of asphalt pavement in dry and saturated conditions under full-scale accelerated loading. The trends of the modeling results were consistent with those of field measurements. The increase in vehicle load significantly increased the magnitudes of stress, strain, and pore water pressure, while vehicle speed showed an obvious impact on pore water pressure. The dynamic responses decreased with pavement depths. Water made the dynamic responses more complex, and pore water pressure significantly decreased with depth within the upper layer of saturated asphalt pavement. Transverse distributions of indicators presented obvious compressive states in the regions in direct contact with vehicle wheels, while tensile states were found in the range of the middle vehicle axle. The numerical results provided a basis for field measurements in future studies, especially for the exploration of factors of temperature and layer depth.
The wave velocity of acoustic emission (AE) can reflect the properties of materials, the types of AE sources and the propagation characteristics of AE in materials. At the same time, the wave velocity of AE is also an important parameter in source location calculation by the time-difference method. In this paper, a new AE wave velocity measurement method, the arbitrary wave (AW) method, is proposed and designed to measure the AE wave velocity of an asphalt mixture. This method is compared with the pencil lead break (PLB) method and the automatic sensor test (AST) method. Through comparison and analysis, as a new wave velocity measurement method of AE, the AW method shows the following advantages: A continuous AE signal with small attenuation, no crosstalk and a fixed waveform can be obtained by the AW method, which is more advantageous to distinguish the first arrival time of the acoustic wave and calculate the wave velocity of AE more accurately; the AE signal measured by the AW method has the characteristics of a high frequency and large amplitude, which is easy to distinguish from the noise signal with the characteristics of a low frequency and small amplitude; and the dispersion of the AE wave velocity measured by the AW method is smaller, which is more suitable for the measurement of the AE wave velocity of an asphalt mixture.
Asphalt binder plays an important role in the overall resistance of asphalt mixture to the moisture damage induced by a dynamic pore water pressure environment. This study evaluates the moisture sensitivity of asphalt binder from the perspective of rheological behaviors using the dynamic shear rheometer (DSR) and the bending beam rheometer (BBR) methods at high, medium, and low temperatures. The damage mechanism is further discussed quantitatively based on the Fourier transform infrared spectroscopy (FTIR) method. The results indicate that a longer conditioning duration is beneficial for asphalt binder to recover its adhesion at 60 °C in multiple stress creep recover (MSCR) tests, but the increasing pore water pressure magnitude of 60 psi held an opposite effect in this study. The asphalt binder’s fatigue life at 20 °C in linear amplitude sweep (LAS) tests decreased obviously with conditioning duration and environmental severity, but the reducing rate gradually slowed down, while the groups of 50 psi—4000 cycles and 60 psi—4000 cycles held a comparable erosion effect. Both the stiffness and relaxation moduli at −12 °C in the BBR tests exhibited an obvious decreasing trend with conditioning duration and environmental severity. The erosion effect on the asphalt binder was gradually enhanced, but it also exhibited a slightly more viscous performance. Water conditioning induced several obvious characteristic peaks in the FTIR absorbance spectra of the asphalt binder. The functional group indexes presented a trend of non-monotonic change with conditioning duration and environmental severity, which made the asphalt binder show complicated rheological behaviors, such as non-monotonic variations in performance and the abnormal improving effect induced by dynamic pore water pressure conditioning.
In the process of the rutting test, the air-void characteristics in asphalt mixture specimens are a dynamic change process. It is of great significance to systematically study the correlation between the change of air-void characteristics and the depth of the rutting slab and establish a relationship with damage. In this paper, the air-void information of rutting specimen sections with different loading cycles (500, 1000, 1500, 2000, 2500, and 3000 times) is obtained by two-dimensional image technology. The dynamic change process of the micro characteristics of internal air voids of two graded asphalt mixtures (AC-13 and AC-16) under cyclic wheel load is analyzed, and it is used as an index to characterize the microstructure damage of the asphalt mixture. The results show that the variation of air-void distribution, air-void shape characteristics, and air-void fractal dimension with the loading process can well characterize the permanent deformation law of the rutting slab. The fractal dimension of the air void increases with the increase in load. It is a dynamic process in which the air-void content changes with crack initiation and propagation. After rutting deformation, the total air-void area and average air-void size of the sample increase, and the total air-void number decreases. Because microcracks are formed in the specimen after rutting damage, the aspect ratio of the air void increases, and the roundness value decreases.