The navigation and positioning subsystem offers important position information for an autonomous underwater vehicle (AUV) system. It plays a crucial role during the underwater exploration and operations of AUV. Many scholars research underwater navigation and positioning. Various improved methods and systems were presented. However, as the diversity of the ocean environment, the random drift of the gyroscope, error accumulation, the variety of tasks, and other negative factors, the navigation and positioning results are uncertain and incredible. The accuracy, stability, and robustness are not guaranteed, which cannot meet the increasing application requirement. Therefore, we put forward a SINS/DVL/USBL integrated navigation and positioning IoT system with multiple resource fusion and a federated Kalman filter. In this method, we first present an improved SINS/DVL combined subsystem with a filtering gain compensation strategy. So we can enhance the accuracy and stability of the navigation and position system. Secondly, we proposed a USBL positioning subsystem with the Kalman filtering acoustic signals to improve USBL positioning performance. Lastly, we present a federated Kalman filter to fuse the positioning information from the SINS/DVL combined positioning subsystem and the USBL positioning subsystem. Through the three methods, we can enhance the positioning accuracy and robustness. Comprehensive simulation results indicated the feasibility and effectiveness of the proposed SINS/DVL/USBL integrated navigation and positioning system, which provides critical reference for other positioning method, and it also offers crucial position information for AUV to achieve high accuracy and efficiency tasks.
7 March 2022 in International Journal of Pavement Research and Technology
The wave velocity of acoustic emission (AE) can reflect the properties of materials, the types of AE sources and the propagation characteristics of AE in materials. At the same time, the wave velocity of AE is also an important parameter in source location calculation by the time-difference method. In this paper, a new AE wave velocity measurement method, the arbitrary wave (AW) method, is proposed and designed to measure the AE wave velocity of an asphalt mixture. This method is compared with the pencil lead break (PLB) method and the automatic sensor test (AST) method. Through comparison and analysis, as a new wave velocity measurement method of AE, the AW method shows the following advantages: A continuous AE signal with small attenuation, no crosstalk and a fixed waveform can be obtained by the AW method, which is more advantageous to distinguish the first arrival time of the acoustic wave and calculate the wave velocity of AE more accurately; the AE signal measured by the AW method has the characteristics of a high frequency and large amplitude, which is easy to distinguish from the noise signal with the characteristics of a low frequency and small amplitude; and the dispersion of the AE wave velocity measured by the AW method is smaller, which is more suitable for the measurement of the AE wave velocity of an asphalt mixture.
Acoustic emission (AE) and digital image correlation (DIC) technology were used in this study to monitor the behavior of reinforced concrete pipe (RCP) in the optimized three-edge bearing test (TEBT). At the same time, the AE source location of different pipe sections was simulated. The results show that the whole compressive loading process for RCP could be divided into 3 to 4 stages. Both the AE counts and AE energy could well characterize the cracking of concrete, and AE energy was more sensitive to the breaking of steel bar. The amplitude and duration of AE signal produced by the breaking of steel bar were larger than those produced by the cracking of concrete. The AE frequency for concrete cracking was relatively scattered. The AE frequency for steel bar breaking was small and concentrated, and this frequency distribution showed an exponential decreasing trend. The results of optimized AE source location showed that the generation and development of cracks occur in the initial loading stage. The results of multi-index analysis showed that the cracks in the top (loading position) and the bottom (bearing position) of the RCP show that the cracks extend from the inner wall to the outer wall, while the cracks on the left and right sides perpendicular to the loading direction show that the cracks extend from the outer wall to the inner wall.
To improve the low-temperature crack resistance of asphalt pavement, this paper investigates the effects of fiber length, content, and type on the flexural and tensile properties of asphalt mastic. Firstly, a numerical program was developed in MATLAB to establish a three-dimensional finite element model of asphalt mastic with an uneven fiber distribution in ABAQUS. Then, the Burgers model selected for simulation was obtained through the asphalt low-temperature bending beam rheological test (BBR). Constructing a three-point bending virtual test of asphalt mastic using a three-dimensional fiber model and systematically analyzing the influence of fiber parameters on bending and tensile properties. The accuracy of the three-dimensional fiber model was verified through BBR experiments. The finite element simulation results show that the addition of fibers can significantly improve the tensile performance of asphalt mastic; increasing the fiber content or length can reduce the peak stress at the bottom of the mid-span and delay cracking. The higher the fiber elastic modulus, the smaller the vertical displacement of the specimen. The model established in this article can effectively elucidate the mechanism of fiber reinforcement, providing a theoretical basis for optimizing fiber parameters and improving the crack-resistance performance of asphalt pavement.