This work studies a near-surface layer microstructure in Ti-6Al-4V alloy samples subjected to plasma electrolytic polishing (PEP) and subsequent high-energy ion implantation with nitrogen (II). Samples with a conventional coarse-grained (CG) structure with an average α-phase size of 8 μm and an ultrafine-grained (UFG) structure (α-phase size up to 0.35 μm) produced by equal channel angular pressing were used in the studies. Features of phase composition and substructure in the thin surface layers are shown after sequential processing by PEP and II of both substrates with CG and UFG structures. Irrespective of a substrate structure, the so-called “long-range effect” was observed, which manifested itself in enhanced microhardness to a depth of surface layer up to 40 μm, exceeding the penetration distance of an implanted ion he. The effect of a UFG structure on depth and degree of surface hardening after PEP and ion-implantation is discussed.

Vit105 (Zr_52.5Cu_17.9Ni_14.6Al₁₀Ti₅ at. %) bulk metallic glass samples were processed by high-pressure torsion and accumulative high-pressure torsion. By DSC, XRD and SANS methods it was shown that accumulative high-pressure torsion allows for achieving high real strains and leads to an increase in the free volume and significant transformation of the structure. Minor crystallization was detected after high-pressure torsion processing.

It is known that zinc biodegradable alloys are a promising material for producing biomedical implants for orthopedics and vascular stents. Among them, the Zn-Ag-Cu zinc alloy is of special interest due to the antibacterial and antimicrobial properties of Ag and Cu. To improve the mechanical properties of the Zn-4Ag-1Cu zinc alloy, the effect of equal-channel angular pressing (ECAP) on the microstructure and strength has been investigated. The ECAP conditions for the Zn-4Ag-1Cu alloy were chosen by modeling in the Deform 3 D program (temperature and strain rate). The microstructure was analyzed using transmission electron microscopy, scanning electron microscopy and X-ray diffraction analysis. The study of strength was carried out by measuring the microhardness and tensile tests of small samples with a gauge dimension of 0.8 × 1 × 4 mm³. The microstructure after ECAP was characterized by equiaxed grains ranging in a size from 1.5 µm to 4 µm with particles in a size from 200 nm to 1 µm uniformly distributed along the boundaries. The ECAP samples showed a high strength of 348 MPa and good ductility of up to 30%, demonstrating their great potential as promising materials for producing medical stents.

Grade 91 (9Cr-1Mo) steel was subjected to various heat treatments and then to high-pressure torsion (HPT) at different temperatures. Its microstructure was studied using transmission electron microscopy (TEM) and X-ray diffraction (XRD). Effects of the tempering temperature and the HPT temperature on the microstructural features and microhardness in the ultrafine-grained (UFG) Grade 91 steel were researched. The study of the UFG structure formation takes into account two different microstructures observed: before HPT in both samples containing martensite and in fully ferritic samples.

In this paper, the authors consider the mechanisms of formation of high-strength states in the Zn–1%Li–2%Mg alloy as a result of its processing by the high pressure torsion (HPT) method. For the first time, the study showed that using HPT treatment, as a result of varying the degree of deformation at room temperature, it is possible to increase the ultimate strength of a zinc alloy from 155 to 383 MPa (with an increase in the yield stress from 149 to 306 MPa) without losing its ductility. To explain the reasons for the increase in the zinc alloy mechanical properties, its microstructure was analyzed by scanning electron microscopy (SEM), X-ray phase analysis (XPA), X-ray diffraction analysis (XRD), and small-angle X-ray scattering (SAXS). Using XPA, the authors established for the first time that Zn(eutectic)+β-LiZn4(eutectic)→~LiZn3+Zn(phase)+Zn(precipitation) and MgZn2→Mg2Zn11 phase transformations occur in the zinc alloy during HPT treatment. SEM analysis showed that at the initial stages of HPT treatment, cylindrical Zn particles with a diameter of 330 nm and a length of up to 950 nm precipitate in β-LiZn3 phase. At the same time, the SAXS method showed that needle-like LiZn4 particles with a diameter of 9 nm and a length of 28 nm precipitate in the Zn phase. The study established that, only spherical Zn and LiZn4 particles precipitate at high degrees of HPT treatment. Precision analysis of the zinc alloy microstructure showed that HPT treatment leads to grain refinement, an increase in the magnitude of crystal lattice microdistortion, a growth of the density of dislocations, which are predominantly of the edge type. As a result of the analysis of hardening mechanisms, the authors concluded that the increase in the zinc alloy strength characteristics mainly occurs due to grain-boundary, dislocation, and dispersion hardening.